Powercore PLUS Desk User manual

Powercore
PLUS Desk
Resetting your desk
Powercore desks need to be reset after assembly and
prior to use. Follow these steps:
1. Press and hold down both the up arrows and down
arrows simultaneously for 7 full seconds until the
desk starts moving down.
2. Keep the buttons pressed all the way to the bottom.
(The screen will show E00 just before it reaches the
bottom).
3. When it reaches the bottom it will “beep” and reset.
When it “beeps” you can release the buttons and it
should show the height of the desk. The desk is
ready to go.
If the screen shows E00 and doesn’t beep, the reset
hasn’t been completed properly so you need to repeat
the process.
When the desk goes to it’s lowest level it is because the
sensors are telling the controller that the desk is possibly
uneven and needs to be leveled at it’s bottom height.
Manually adjusting the height
Simply press the “up” or “down” arrows to go to your
required height.
Setting automatic height adjustment
If you want to use the memory function to automatically
move to preset heights, follow these steps:
1. Move the desk to the height you want to assign
a preset memory number to.
2. Press “M” and hold it down until the screen starts
lashing. Release the “M’ button and select the
number you want to allocate that height to
(1, 2, 3 or 4).
3. When the P- (number allocated) shows on the
screen - you have successfully allocated that
preset (1, 2, 3 or 4) to the height.
4. Move the desk to another height level and repeat
the procedure to other preset numbers (1,2,3 or 4)
To move the desk to a preset height level just press
the number (1,2,3 or 4) and release. The desk will
move to that preset height.
You can overwrite these settings any time by
repeating the process and re-allocating the preset
number to a dierent height.
Error messages
If the handset on the desk shows an error message
(E - “number”) it is a good chance the desk just
needs a reset. Follow the instructions at the top of
this page.
If the error message persists (despite the reset):
email [e-mail] with the error
message and I’ll get in contact to help you. Most
solutions are pretty simple.
Here’s the low down on your desk and how to set it up.
Watch the assembly video: vimeo.com/371500187
Enjoy your desk
and your mobility
powercore.nz
Powercore_assembly instructions_Plus desk_A4.indd 1Powercore_assembly instructions_Plus desk_A4.indd 1 11/05/22 2:25 PM11/05/22 2:25 PM

Lifting system 1 set
2
16
Foot
M6*14 screw
2Bracket
M6*10 screw 8
Support beam 1
8
4mm hex spanner 1
M6*12 screw
Rubber cushion 6
2ST3. 5*19 screw
ST4 .8*19 screw 8
4mm hex spanner
4mm hex spanner
4mm hex spanner
4mm Hex Spanner
Loosen the 4 screws of beam using 4mm hex spanner,
adjust the beam to proper position to fit the desktop.
Attach legs to the beam using 8 of M6*14 screws and 4 of M6*12 screws.
M6*12 screw 4PCS
M6*14 screw 8PCS
Overturn frame and attach brackets to beam using 4 of M6*12
screws, and then fit the rubber cushions to the brackets and beams.
Screw the frame onto
the top using 6 of
ST4.8*19 self-tapping
screws. Then use 2 x
ST4.8*19 to screw the
control box in place.
Finally attach the
handset to the front
side of the desktop
using 2 x ST3.5*19
self-tapping screws.
Attach feet to the legs using 8 of M6*14 screws.
4mm hex spanner
Adjust the width of desk frame to fit the desktop by sliding the beam,
we recommend leaving at least 5-8cm of the desktop width (on each
end) protruding beyond the frame width and centering the side
brackets fore and aft.
Connect the control
box to the handset and
to the two motors
(doesn't matter which
motor goes in which
slot). Connect the
power cable, plug it in
and you’re ready to roll.
M6*14 screw 8PCS
M6*10 screw 8PCS
M6*12 screw 4PCS Rubber cushion 6PCS
Parts and tools list
7
8
6
5
4
1
9
10
11
Qty QtyName Name
3
2
Assembly instructions
12
3 4
56
789
10 11
1
2
3
4
56
7
By the way, we pack one extra screw (of each type) in case you lose one when unpacking. Don’t panic when you see you have an extra one.
Powercore_assembly instructions_Plus desk_A4.indd 2Powercore_assembly instructions_Plus desk_A4.indd 2 11/05/22 2:25 PM11/05/22 2:25 PM