Clean the exterior of the appliance with a damp cloth. The appliance may NOT be
immersed in water. Wash the Nozzles r with water & detergent with a non-abrasive sponge
if you wish. DO NOT use metal scouring pads. Dry the Nozzles thoroughly before attaching
it onto the appliance.
Ensure that the ON/OFF & Speed Switch is set to 0 (OFF). Insert the plug of the power cable
to the electric mains and switch it ON. Holding the appliance by the Handle, select the
desired speed (3 for drying hair or 2 for styling hair) or Cool function.
Make sure to remove any label or protective sheet which may prevent its proper functioning.
cover the appliance during functioning;
use while you are tired or sleepy;
cover or block the Air Inlet or Air Outlet of the appliance during operation or place it on a
soft surface, such as a bed or couch, where the Air Inlet or Air Outlet may be blocked;
insert metal objects into the air grilles to avoid electric shock or body parts inside the
protection cover of the appliance;
allow hands, hair, clothing, curtains, and any other objects to come into contact with the
appliance’s motor and accessories to avoid personal injury or damage to the appliance
when the appliance is in operation;
use the appliance if blades are bent, chipped, cracked, broken or in any way damaged;
tamper with the appliance’s components as this appliance contains no user-serviceable
parts and doing so may cause unnecessary damage;
attachments (Nozzles, Air Inlet Cover) may be hot during use. Allow them to cool before
handling;
use the appliance on artificial hair;
wind the power cable round the appliance;
operate the appliance for more than 5 minutes without interruption. Let the appliance rest
for 10 minutes between processing cycles. After 3 processing cycles, allow an interval of 15
minutes to let the appliance cool down before the next use so as to prolong its service life.
DO NOT allow the appliance to idle while in operation;
press the ON/OFF & Speed Switch too hard so as to avoid any damage;
leave the appliance unsupervised during operation.
14.
15.
16.
17.
18.
19.
20.
DO NOT use or store the appliance outdoors. Store and use the appliance only indoors, or in
any case, protected from weathering such as rain, direct radiation of the sun and dust.
Operation
If you are using the appliance for the first time, you should:
a.
b.
c.
DO NOT:
•
•
•
•
•
•
•
•
•
•
•
•
•
During operation, DO NOT touch the appliance with wet body parts, and it is recommended
to have between you and the standing surface, an isolating element (for example, wearing
shoes with rubber soles).
DO NOT use this appliance while bathing or showering. DO NOT use, place or store this
appliance near bathtubs, showers, toilets, basins or other vessels containing water. When the
appliance is used in a bathroom, unplug it after use since the proximity of water presents a risk,
even when the appliance is switched off. DO NOT operate this appliance if it has a damaged
plug or power cable, if it is not working properly, or if it has been damaged or dropped,
especially into water. Return the appliance to a service centre for examination and repair.
DO NOT soak the appliance in water or other liquids, wash it under the tap, or let any liquid
flow into the internal casing of the appliance to prevent electric shock. In case of accidental
fall in water, DO NOT try to take it out, but first of all unplug immediately the power cable
from the socket.
DO NOT direct hot air toward any person or animal, especially the eyes or other heat sensitive
areas to prevent possible burns or scalding.
Note: USING HUMAN HAIR DRYERS CAN ACTUALLY HARM YOUR PET. Animals such as
dogs and cats have thinner skins (especially domestic cats) than humans and run the risk of
being burned if the temperature is set too high. When blow drying your pet’s coat, it is
recommended to use a hair dryer specifically designed for that particular animal.
Switch off the appliance by turning the ON/OFF & Speed Switch to ‘0’ (OFF) and unplug the
socket from the electric mains and wait until the appliance has cooled down before changing
accessories, storing, cleaning or performing any maintenance operation.
3
