POWERSHADES PSRMT MC 2022 User manual

REMOTE GUIDE
Multi-Channel
PSRMT_MC_2022
PSRMT_MCOW_2022
POWERSHADES

PSRMT_MC_2022
PSRMT_MCOW_2022
UP
DOWN
CH -
UP
DOWN
CH -
CH +
PROGRAM
BUTTON (P)
PROGRAM
BUTTON (P)
FAVORITE
FAVORITE
STOP
CH +
STOP
Multi-Channel Handheld Remote
Multi-Channel Wall Remote
POWERSHADES
1

POWERSHADES
Motor Buttons
Screen Indicators
Specifications
LOW BATTERY
INDICATOR
GROUP
INDICATOR
FAVORITE
BUTTON
(LEFT/RIGHT)
BUTTONS
(UP/DOWN)
BUTTONS
STOP
BUTTON
DIRECTIONAL
INDICATORS
18mm30mm15mm
25 mm 35 mm DC 35 mm AC
2

POWERSHADES
Adjusting Top Limit
If your limits are already set and you would like to adjust your top limit, follow the quick and
easy steps below.
1. Move your shade to the top limit using the Up/Down Buttons.
2. Hold the Up Button and the Stop Button for 5 seconds until the shade jogs twice
3. Jog the shade with your Up/Down Buttons to your new desired top limit.
4. Hold the Up Button and the Stop Button for 2-3 seconds. The shade will jog to indicate
that the new top limit is set.
Limit setting
Your shade(s) should have limits set when they arrive at your facility. If for any reason your limits
are not set, follow the quick and easy instructions below to set your desired shade limits.
Top Limit can be set by moving the shade to the desired top position using the Up/Down
Buttons, then hold the Up Button and the Stop Button for 2-3 seconds. The shade will jog to
indicate that the top limit is set.
Bottom Limit can be set by moving the shade to the desired bottom position using the
Up/Down Buttons, then hold the Down Button and the Stop Button for 2-3 seconds. The
shade will jog to indicate that the bottom limit is set.
Pairing Motors to Channels
1. Select Channel using (Left/Right) Buttons
2. Hold motor button for two seconds - motor jogs up and down
3. Hold Stop Button on remote for 3 seconds - motor jogs up and down. The motor is
now paired to the remote.
To unpair the remote from the motor, repeat the steps above.
To pair a back-up remote to the motor, press the (P) button 2 times on Remote A
(already paired existing remote) then press the (P) button once on Remote B (new
remote).
Direction Reversing
Can be done by holding the motor button for three jog cycles (this works even if limits have
been set)
If limits haven’t been set, you can hold the Favorite Button and the Stop Button for 2 seconds.
3

Slowing Motors Down
Press the (P) Button on the back of the remote once, then the Down Button twice. You
need to wait for the motor to respond between button presses.
Adjusting Bottom Limit
If your limits are already set and you would like to adjust your bottom limit, follow the quick
and easy steps below.
1. Move your shade to the bottom limit using the Up/Down Buttons.
2. Hold the Down Button and the Stop Button for 5 seconds until the shade jogs twice
3. Jog the shade with your Up/Down Buttons to your new desired bottom limit.
4. Hold the Down Button and the Stop Button for 2-3 seconds. The shade will jog to
indicate that the new bottom limit is set.
POWERSHADES
Setting Favorite Position
1. Move your shade to desired favorite position with the Up/Down Buttons then press
the (P) Button
2. After the shade responds, press the Stop Button
3. After the shade has responded again, press the Stop Button and the shade will jog
twice.
You can now navigate to the favorite position by using the Favorite Button:
You can remove it by moving the shade to the favorite position, then doing the exact same set
of commands.
Speeding Motors Up
Press the (P) Button on the back of the remote once, then the Up Button twice. You need to
wait for the motor to respond between button presses.
4

Setting Number of Channels (Optional)
1. Select Channel “01” using (Left/Right) Buttons
2. Press Favorite Button and Right Button for 3s - display will show
3. Remote will go to channel 16 with the directional indicators on the side
4. Select the final channel you want (cannot be higher than 16 or lower than 1) using
(Left/Right) Buttons
5. Short press (click/tap and immediately release) the Stop Button, display will show
POWERSHADES
Position Percent Setting (Accurate Positioning)
Limits MUST be set before using this feature
1. Press the Stop Button three times
2. Use the (Left/Right) Buttons to increase or decrease percent
3. After 2 seconds, the shade will move to that limit
Advanced Options
5

Setting Number of Groups (Optional)
1. Select Channel “00” using (Left/Right) Buttons
2. Press Favorite Button and Right Button for 3s - display will show
3. Remote will go to group 6 with the directional indicators on the side
4. Select the final group number you want (cannot be higher than 6)
5. Short press (click/tap and immediately release) the Stop Button, display will show
If you select Channel “00” as your final channel, you will have no groups on the
remote. They can be re-added following these steps and selecting the number of
groups desired.
POWERSHADES
6

POWERSHADES
Modifying (Adding + Deleting Channels from Groups)
1. Select Desired Group using (Left/Right) Buttons
2. Press Favorite Button and Right Button for 3s - display will show
3. Remote will go to channel 1 with the group and directional indicators.
4. Navigate to desired channel to add or remove by using (Left/Right) Buttons
5. Short press Favorite Button to add to the group.
If the channel has already been added, it’ll flash on and off. Press the favorite button
again to remove it from the group.
6. Once channels are added to the desired group, short press the stop button. Display will
show:
7
Removing Groups
1. Using the (Left/Right) Buttons , navigate to group “00” on the screen
2. Hold the
Favorite Button and the Right Button until the screen displays “06” and the
Group Indicator

Factory Reset
To remove all shade pairings and limits, hold the motor button until the shade jogs 4 times.
3. Using the (Left/Right) Buttons , navigate to group “00” on the screen again.
4. Short press the Stop Button
5. Using the (Left/Right) Buttons, confirm the Groups Indicator no longer appears on the
screen.
To add Groups back to your remote, repeat these steps, but instead of choosing “00” on Step 3.,
choose the number of groups to show before pushing the Stop Button.
POWERSHADES
Mounting Handheld Remote
1. Place the magnetic remote mount on a wall
where you’d like your remote to reside.
2. Using the two screws provided, screw the
mount into the wall through the designated
screw holes.
3. Make sure the mount is secure and place
your remote on the magnetic mount.
Locking Function
1. Hold the (P) Button on the back of the remote for 10 seconds. Your screen will display the
icon below when locking function is activated.
2. To
unlock , repeat Step 1.
When locked, these programming setting functions are not allowed
WALL
8
Mounting Instructions

POWERSHADES
Caution
1. The transmitter should not be exposed to moisture or impact.
2. During use, when the remote control distance is significantly shorter or less sensitive,
please check to see if the batter needs replaced.
3. When the battery voltage is too low, the LCD screen will show a low battery indicator
prompting to replace the battery.
4. Please properly dispose of the used batteries
9
Mounting Wall Remote
1. Remove magnetic mount from the back of the
remote and place on the wall in a desired
location where you’d like the wall remote to
reside.
2.
Using the two screws provided, screw the
mount into the wall through the designated
screw holes.
3. Make sure the mount is secure and place your
remote on the magnetic mount.
WALL