Powersolve Hseuireg07201 series User manual

HSEUiREG07201(R2) MANUAL

HSEUiREG07201

0W Lab Power Supply

DIN

Rail

Features

•Real time voltage programming

•Real time & value C/V-monitoring

•Reference voltage f. autonomous programming

•Remote Shutdown

•Sense control 2V per load line

•Power Good Relay DC-ok

•Quick down programming option PS

•Precise dynamics on load change

•Series & parallel operation N+1

•Natural convection

•Electronic Inrush Limiter 13,8Arms

•Up to 90% efficiency

•EMI/EMS EN61000-6-2,3, EN55032 class B

•EN61010-1, EN61010-2-201, EN62368-1

Model

Voltage

programmable

Current

programmable

HSEUiREG0

.018

–

18Vdc

–

HSEUiREG0

–

30Vdc

–

HSEUiREG0

–

0Vdc

–

HSEUiREG0

–

60Vdc

–

15,0A

HSEUiREG0

–

90Vdc

–

HSEUiREG0

130

–

0Vdc

–

7,0

HSEUiREG0

.18

–

180Vdc

–

HSEUiREG0

240

–

240Vdc

–

[email protected]

www.powersolve.co.uk

020321

HSEUiREG07201(R2) MANUAL

Technical description

The Camtec HSEUiREG models are high-precision lab power supplies „Made in Germany“. These

power supplies are designed for power systems in the testing automation.

For more than 25 years the Camtec Power Supplies manufactures high-end switch mode power supplies in

Germany. A field breakdown of below 0,004% over a 10-year period under review approves our ambitious

quality concept. Each manufactured Camtec product passes several 100% tests for each detailed function and

a full-load Burn-In test.

Although it is not required from the safety norms our production applies a routine safety test to each

manufactured device, even if it is an extra low-voltage model. The components in the assembled device pass

stress aging to achieve an even level and to prevent from delayed failures. Our internal product engineering

guidelines provide a clear target: Camtec product reputation must say „mount and forget“. Quality is never a

mere promise for our team.

The HSEUiREG laboratory power supplies provide low noise and ripple, a very quick programming, and a

precise setting at high load changes. With an efficiency up to 90% the devices are highly energy efficient.

Equipped with high-end capacitors of outstanding lifetime our power supplies guarantee a very long and

reliable operation time. The circuit design of the HSEUiREG Series allows cope playing with complex loads.

The internal protection circuits protect the power supply and the connected system, even in exceptional

situations. The HSEUiREG series is protected from high transients by strong filters with high energy efficiency.

All inputs and outputs are electrically isolated. The design specifications call for the highest standards of safety

and interference suppression. The unit is designed in accordance with the EN61010-1, EN61010-2-201,

EN62368-1, EN60950-1, and the EMC-compatibility with EN55032.

The special heat emission design supports easy baseplate cooling with the help of an optional wall mount

plate.

[email protected]

www.powersolve.co.uk

020321

HSEUiREG07201(R2) MANUAL

Features

Idling behavior

The HSEUiREG Series is permanently open-circuit proof.

When an output voltage is preset it comes stable. If a load is

switched suddenly, the unit stabilized within <1ms. An

overshoot of the output voltage is irrelevant.

Start behavior

The power supply has a start delay of 420ms to stabilize all

measuring circuits for the interface messages accurately.

The power supply starts with a ramp (soft start) of 100ms.

The output voltage does not overshoot - regardless of

whether a load is connected or not.

Galvanic isolation and insulation

The switching power supply is galvanically isolated between

the input and the output. The sensing, Ureg, Ireg, Umon,

Imon and Iref are connected to the DC power output.

Voltage programming (Ureg)

The output voltage of the HSEUiREG power supply can be

adjusted by a control signal. The setting is linear to the input

signal.

Current programming (Ireg)

The output current of the HSEUiREG power supply can be

adjusted by a control signal. The setting is linear to the input

signal.

Voltage Monitor (Umon)

The power supply provides real-time monitoring of the output

voltage. It is the exact and real value at the output terminals.

If the sense line is used, the real value is measured directly

at the load. The latency signal preset to the measured value

is negligible since the control circuit is constructed

completely analogously.

Current Monitor (Imon)

The power supply provides real-time monitoring of the output

current. It is the exact and real value at the output terminals.

The latency signal preset to the measured value is negligible

since the control circuit is constructed completely

analogously.

Constant Voltage or Constant Current Mode (CV/CC)

The device can optionally be operated as a DC voltage

source or a constant current source. The operating mode is

signaled via LED.

Reference Voltage (Uref)

The devices feature an auxiliary reference voltage to operate

external potentiometers. The Uref voltage can be set to 5,2V

or 10,4V 5mA via the DIP-switch.

Sense Mode

The power supply has a sense mode to compensate for

voltage drops of 2V per load line.

External Shutdown (SD)

All the models are featured with an external shutdown

(switch/open collector)

Digitale Interface

The standard equipment of the power supply is an analog

interface.

Optionally, the unit can be equipped upon request with a

digital USB 2.0 interface. Options include a software and a

DOM interface for easy control over standard software like

LabView or others.

DC Power Good Relay

The power good relay connection indicates over device

temperature and low AC supply voltage.

Over Temperature Thermal Shutdown (OT)

The device has a thermal monitoring: shutdown with

automatic restart.

Fast Down Programming & PowerSink (PS)

For fast down programming an internal PowerSink is offered

as an option. The current sink discharges the output

electrolytic capacitors and eleminates back feed energy.

A further output allows to control external PowerSink

modules. The internal current sink for quick programming

must be installed at the factory.

ST-HD (ST Heat Dissipation)

Our aligned and controlled heat dissipation design opens

possibilities that are formerly being reserved to custom

design power supplies: Hard mount of the HSEUiREG power

supply modules on a wall allows easy access to base plate

cooling.

In practice that means that one can mount the modules onto

a thermal conducting wall to unsure that a sigificat part of the

losses wil be transported directly out of the power supply

unit.

[email protected]

www.powersolve.co.uk

020321

HSEUiREG07201(R2) MANUAL

Technical Data Table

AC Input Range

132Vac, 184

264Vac

(115/230Vac input

selector, factory setting is 230Vac)

AC I

put Frequency

63Hz

DC Input Range

250

375Vdc

(input selector set to 230Vac)

AC Input Rated

115Vac <

12,7

A, 230Vac <

7,2

Input Rated

250Vdc

3,6

375

Vdc

2,4

DC V

oltage

programmable

18Vdc

30Vdc

50Vdc

60Vdc

90Vdc

130Vdc

180Vdc

240Vdc

DC C

urren

t programmable

40A

30A

18A

15A

10A

Over Voltage Protection

22Vdc

35Vdc

59Vdc

70Vdc

105Vdc

150Vdc

210Vdc

280Vdc

Over Current Protection

44A

33A

19,8A

16,5A

11A

7,7A

5,5A

4,2A

Ripple Noise 230Vac 20MHz

40mVpp

100mVpp

120mVpp

150mVpp

200mVpp

300mVpp

400mVpp

Load Regulation 0

100%

< ±0,05%

Power Maximum

, 90

132Vac, 184

264Vac

Cooling

Natural convection

Efficiency

Up to

230Vac

at full load

Short Circuit Resistance

yes

Open Circuit Protected

yes

Base Load (OCP)

Non required

(

open circuit protected

)

Load

Regulation Time

<1ms on load switch 10

100%

Accuracy

Ureg:

≤

± 0,

Ireg:

≤

± 1

Umon:

≤

± 0,5%

Imon:

≤

± 1

, Uref:

≤

±1

Temperatur

e Control

, therm

al shutdown

& autorecovery

0°C,

outside

measuring point distance

0mm)

Hold Up Time

0ms 230Vac

ins buffering at full load

Inrush Current

9,8

rms

13,8

Apeak 230Vac

tive

electronic

inrush protection

(

simple

NTC)

MCB (Circuit Breaker)

16A curve

@ 230Vac

/ 25A curve B @ 115Vac

Start

up Delay

yp.

420m

230Vac, 590ms

115Vac

Softstart

yp. 100ms

Start

up from Shutdown

Typ.

Ambient Temperature

0°C…+

°C

operating, derating 2,5%/°C >

0°C

Storage Temperature

40°C…+85°C

mbient Conditions

Humidity 95

non

condensing

25°C

, climate class 3K3,

pollution degree 2

ROHS

2011/65/EU, (EU)2015/863

REACH

EG No. 1907/2006

EMI

EN55032 class B, EN61000

EMS

EN61000

afety

EN61010

1, EN61010

201, EN62368

EN60950

EN60204

Protection

Class

PE connection

required

Isolation

Input to

Output

3000Vac

Isolation

Input to

Case

2500Vac

Isolation

Output to

Case

500Vdc,

≥

0Vdc

00Vdc

MTBF (IEC61709)

400

000h

(Meantime Between Failure

statistic

time

between failures

after

repairs

)

MTTF

(IEC61709)

212

(Meantime To Failure: statistic time to ever fails

)

Dimensions (HxWxD)

0x1

Weight

3,1

lbs

AC Terminals

Input Screw Terminal 3x 0,5

–

16mm²

AWG26

–

AWG6

(L,N,PE)

, technical data see “connections”

DC Terminals

Output Screw Terminal 4x 0,5

–

16mm²

AWG26

–

AWG6

(+ + /

)

technical data see “connections”

[email protected]

www.powersolve.co.uk

020321

HSEUiREG07201(R2) MANUAL

Manual

nd Techni

cal Details

Programming Time Vout [ms]

Model

18V

30V

50V

60V

90V

130V

180V

240V

Rise Time

100%, 10/100% load, [ms] typ.

15/15

Slew Rate 90

10%, 10/100% load, [ms] typ.

37/3,7

104/10,4

51/5,1

74/7,4

57/5,7

53/5,3

100/10

83/8,3

Slew Rate PS

Option 100

0%, 0% load, [ms] typ.

100

Output Capacity, [mF] typ.

10,4

1,85

0,64

0,28

0,13

Analog

Interface

CON

(

Connector Model

Weidmue

ller

159746

0000

included

)

Name

Typ

Func

tion

Signal

Remarks

Ureg +

Input

Voltage Programming Select 0-5V, 0-10V,

0-20mA, 4-20mA

1 MΩworking resistance with Vprog

500 Ωworking resistance with Iprog

Ureg

Input

Ireg +

Input

Current Programming Select 0-5V, 0-10V,

0-20mA, 4-20mA

1 MΩworking resistance with Vprog

500 Ωworking resistance with Iprog

Ireg

Input

Umon +

Output

Voltage Monitor Select 0-5Vdc/5mA,

0-10Vdc/5mA

Umon

Output

Imon +

Output

Current Monitor Select 0-5Vdc/5mA,

0-10Vdc/5mA

Imon

Output

SD +

Input

Control Signal Shutdown

Switch / Open Collector

Input

Uref +

Output

Reference Voltage Select 5,2Vdc or 10,4Vdc

5mA

Uref

Output

Analog Interface

CON

(Connector Model Weidmueller 1

597

0000 = included)

Name

Type

Function

Signal

Remarks

Output

Closers, Signal DC OK Relay Potential-free break contact

Output

AUX +

Output

Sense +

Input

Sense

Input

AUX

Output

Analog Interface CON

(Connector Model Weidmueller

1597360000

= not included)

PS +

Output

External Power-Sink Trigger This connection is without function

for the standard HSEUiREG1500

Output

Configuration of the Analog Interface via Dip

Switch

Mode

S10

10V

20mA

LED Signal Indication

LED Over Temp. Shut Down Constant [V] Constant [C]

CV OFF OFF ON OFF

CC OFF OFF OFF ON

OT ON OFF OFF OFF

SD OFF ON OFF OFF

[email protected]

www.powersolve.co.uk

020321

HSEUiREG07201(R2) MANUAL

Monitor Outputs

Monitor Connections

Potentiometer Programming

Programming Inputs

Shutdown

Power OK Relay

LED Indication

GRN

Constant

voltage

YEL

Constant current

YEL

hutdown

RED

Over temperature

[email protected]

www.powersolve.co.uk

020321

HSEUiREG07201(R2) MANUAL

Programmi

Monitoring V/C

nalog

Interface

(Ureg

/Ireg)

(Umon/Imon)

The standard programming of the HSEUiREG Series is an analog interface. The output voltage is linearly

proportional to the adjusted analog control signal. If the control signal 0V and/or 0A applies the power supply

delivers 0V at the output. The power supply is already working from 0V output voltage and low load with high

precision.

The monitor signal is analog linear to the output voltage. The monitor signal for current and voltage is the real

value that is measured directly at the output of the power supply. If a sense line is connected to compensate for

the voltage drop across the load lines, the monitor signal is exactly the value that is measured at the connection

point of the sense line. The description of the power supply in the sense operation is carried out in a separate

section.

The analog inputs and outputs are non-floating. The mass is connected to the DC negative output.

The adapter provides the ability to select the desired input / output via a DIP switch. The burden of the control

voltages is 1MΩ. The burden of the current interface is 500Ω. The latency to full compensation of V/C on the

interface from 0-100% is 15ms for all HSEUiREG models.

If the power supply is operated with a low load, the down-programming time up to the desired set point may be

very long. The power supply has large built-in capacitors and an enormous energy reserve. A similar effect

occurs by skidding input energy, which is not easily removed from the power supply. A PowerSink (PS) modul

can be ordered as an option for each HSEUiREG power supply unit. The PS option is used for fast down

programming and the degradation of skidding energy fed. The option must be equipped in the factory.

For further information about the PS option, please refer to the technical details in a section PS-option.

ompensation

of Load

Line Drop Voltage

(Sense +/

)

standard operation mode

The HSEUiREG power supply has a Sense Mode to compensate for the voltage drop over long load lines. The

compensation amounts to a maximum of 2V per load line. Under certain circumstances, it can be expected to

apply more complicated external interference suppression. If sense is not used, Sense + and Sense - shall

necessarily be connected by short bridges to AUX + and AUX - (factory setup). Make sure that +/- connections

are matching! WARNING! Reverse polarity of the sense lines can cause damages to the power supply unit.

Sense operation: Remove the bridges between Sense +, Sense -. Connect the sense lines directly to the load.

Pay attention to the polarity of plus and minus of the load to prevent damage to the power supply. To avoid

interference, twist the sense lines. To reduce inductive effects, we recommend that the load lines position is

close to each other. To supply a pulsating load, the use of an electrolytic capacitor and a cermic capacitor has

proved. The internal Over Voltage Protection (OVP) of the power supply controls the DC power directly to the

DC output terminals. In case of an error the OVP acts automatically (see OVP values corresponding table).

The sense terminals are directly connected to the power outputs.

Lokal Sensing Remote Sensing

(factory setup) (twisted sense lines)

[email protected]

www.powersolve.co.uk

020321

HSEUiREG07201(R2) MANUAL

Compensation Load Line Voltage

Drop

(Sense ++/

)

battery

harger

operation mode

Remote Sensing as a battery charger

If the HSEUiREG power supply unit is used as a battery charger, it is recommended to refrain from sensing. It

can lead to severe damage to the power supply, if the polarity of the sense line is confused (field experience:

such error often occurs when system service is required, e.g., when the batteries are changed). If it is

necessary to use sensing, proceed as described in the figure below. Proven approaches are 250mA for the

fuses and 3...5A load capacity of diodes.

WARNING! Reverse polarity of the sense lines can cause damages to the power supply unit.

External Shutdown (

)

The power supply is set to the Shutdown mode, when the

control input is either shorted via a relay contact, a switch

contact or an NPN transistor with open collector (voltage drop

<1V, current typ. 2mA).

If the shutdown repeals the power supply starts again.

Using the soft-start, the current and the voltage rises within

continuously to the default set values.

Power

OK Relay (DC Power Good)

The alarm signal DC OK has potential-free relay contacts. The contacts are closed (relay

coil is energized) when the power output is active. In shut dwon mode (SD) the contacts

are closed.

The contacts are open when the power output is inhibited by OT or low AC supply voltage

at the AC inputs. Contact load (resistive load): 30Vdc/1A, 60Vdc/0.3A, 30Vac/0.5A.

Over Voltage Protection

(OVP)

If an over-voltage occurs to the output (for example, defective components, external feed voltage), it is followed

by the shutdown of the power output. A periodic restart attempts (ticker operation period 400ms).

Over Temperature Shutdown

(OT)

The alarm LED OT lits when the temperature of the power supply is higher than the over-temperature

protection threshold.

[email protected]

www.powersolve.co.uk

020321

HSEUiREG07201(R2) MANUAL

V Chart and Operating Point

The output voltage set Vout is always linear proportional to the control signal Ureg.

The desired control signal is selected via the DIP switcher:

0-5V, 0-10V, 0-20mA oder 4-20mA.

Model Value UA1 (V) Value IA1 (A) Value UA2 (V) Value IA2 (A) Pmax (IA1/IA2)

HSEUiREG07201.018 18Vdc 40,0A

18Vdc

40,0A

720/720W

HSEUiREG07201.030 30Vdc 24,0A

24Vdc

30,0A

720/720W

HSEUiREG07201.050 50Vdc 14,4A

40Vdc

18,0A

720/720W

HSEUiREG07201.060 60Vdc 12,0A

48Vdc

15,0A

720/720W

HSEUiREG07201.090 90Vdc 8,0A

72Vdc

10,0A

720/720W

HSEUiREG07201.130 130Vdc 5,5A

103Vdc

7,0A

715/721W

HSEUiREG07201.180

180Vdc 4,0A 144Vdc 5,0A 720/720W

HSEUiREG07201.240

240Vdc 3,0A 190Vdc 3,8A 720/722W

Inrush Current Protection (electronic)

The power supply unit has an electronic current limiter

(230Vac=9,8Arms/13,8Apeak).

It is a precisely working circuit instead of a usual simple NTC

solution. The accuracy is ±10%, regardless of the operating

temperature and the duty cycles (interval ≥10s). We

recommend the smallest circuit breaker a characteristic B

with 25A for 115Vac and with 16A for 230Vac.

Temperatur

Derating

The maximum ambient temperature during operation is + 60°C. If the

overtemperature protection is activated, the power supply is switched off.

The measuring point is 50mm outside the power supply. The power supply unit

starts automatically when it has cooled down.

Series Operation

Two or more units of the same model and output voltage can be operated up to a total voltage of 300Vdc in

series. Due to the dielectric strength of the internal components used, only the models with an output voltage of

90Vdc and later are approved for series operation. Other power supplies are not approved for series operation

above 60Vdc.

If the units are remotely controlled via the analog interface it is compulsory to use a potential-free control

voltage!

[email protected]

www.powersolve.co.uk

020321

HSEUiREG07201(R2) MANUAL

Parallel

Operation

N+1 Decoupling

To increase the overall power of the power supply, two or

more devices of the same model with the same output

voltage may be operated in parallel. We recommend

using a busbar for the DC power connector. Make sure

that the cable lengths and cable cross-sections of all

power supplies to the busbar or to the star point are

identical. Allow proper connection for low contact

resistance. If you want to use the sensing function,

connect it also to the star point or busbar. To avoid

measurement errors, select the line length from the

neutral point or from the busbar to the load as short as

possible and use the maximum possible conductor cross-

section.

Up to 5 pcs HSEUiREG can be paralleled.

The HSEUiREG models have no internal O-ring diode, to

operate the devices redundant N+1. We recommend

using our RED00202 DIN-rail redundant device.

Electrical Safety (Factory

Test / Field

est Owner)

¹) ≥60Vdc= 2500Vdc

Type and factory test are the manufacturer. While repeating damage can

happen to the power supply unit. For the field test (owner) follow the below instruction:

a) Use suitable test equipment, raising the voltage slowly

b) Short circuit L1 and N, and all the DC output terminals.

c) Use only test voltages of 50/60Hz. The outputs are unearthed and

therefore they have no resistance to GND/PE.

d) If the residual voltage is ≥60Vdc, observe the safety standards.

Use only specially insulated screwdriver to trim the Ua/Ia.

)

Type Test

60s

2500Vac

3000Vac

500Vdc

Factory Test

2000Vac

500Vdc

Field Test

2000Vac

500Vdc

Cut

off

current setting

>20mA

>1mA

[email protected]

www.powersolve.co.uk

020321

HSEUiREG07201(R2) MANUAL

Available Options

PS Option

for Quick Downward Programming

(PSOPT)

Quick Down Programming:

The input capacitance of a power supply can be discharged only slowly at low load. A quick downward

programming of the output voltage of an almost non-loaded power supply is not possible. This fact leads to

undesirably long cycle times on a test bench. The PS option works as an electronic circuit. It communicates

with the control circuit of the power supply and therefore permits a much higher dynamics of the system, as an

external passive base load.

Maximum continuous power capability is 5W. Maximum switching frequency is 1Hz. The switching frequency

must be reduced if external electrolytic capacitors are used.

Back-Feed Energy:

In the back-feed power by a consumer a regenerative current is charging the output capacitors. The output

voltage will increase. The following formula shows dv/dt=i/C.

When an electronic current sink is used, the output voltage remains constant at the set value. The current sink

provides a quick dynamic response.

Fig 1 Fig 2 Fig 3

A Power Sink (see Fig. 1) enables fast down programming at low load conditions or without a load. For

comparison, see Figure 2 (without) and Figure 3 (with PS option).

The PS-option must be installed in the plant because it is not accessible from the outside. It is necessary to

match the power supply after installation and perform electrical safety testing. We therefore recommend a

required a necessary PowerSink option to be purchased with the power supply unit.

Retrofit PS option:

Individual trained HSEUiREG dealer are pre-retrofit able. Alternatively, a HSEUiREG power supply may also be

sent to the factory. Please apply for this an RMA number from our service.

Test Certificate and Calibration

Optionally we offer with the delivery of a HSEUiREG power supply a Manufacturer's Inspection Certificate of

electrical setpoint / actual values. The power supply then is "calibrated". Such Manufacturers Calibration

Certificate for each power supply can uniquely be assigned via the device serial number.

A manufacturer calibration of a HSEUiREG can frequently be done via controlled recirculation on a regular

basis. Please request the help of your local HSEUiREG dealer or contact us directly:

service@camtec-gmbh.com

[email protected]

www.powersolve.co.uk

020321

HSEUiREG07201(R2) MANUAL

Mechanics

HD Baseplate

Cooling & Temperature Management

The temperature management of the HSEUiREG series provides a direct dissipation of the main energy losses.

The internal coolers of the output diodes and the power FETs connect to the back-plate cooler. It is possible to

dissipate about 40 – 50% of the energy losses out of a system while using the Baseplate cooling bundle

2201002001 to hard mount the unit to a plane and heat conductive surface.

[email protected]

www.powersolve.co.uk

020321

HSEUiREG07201(R2) MANUAL

Mechanics & Installation Instruction of the

HSEUiREG

Stable metal/aluminium housing IP20. To allow adequate convection, a free air space of 50mm (top/bottom)

and 10mm (sidewalls) is required; and for active devices 15mm space from the sidewalls. For proper air

convection it is necessary to install the HSEUiREG. One can use the DIN-Rail installation (equiped standard)

with our patented 35mm DIN-Rail bracket according to EN60715. It is easy to mount/dismount while snaping it

onto the 35mm DIN-Rail - no tools necessary. A wallmount back plate (option) is availble, too.

It is not allowed to install the

HSEUiREG

in other mounting direction then

as shown

in the

drawings.

Back Plate Option / DIN-Rail Standard

(The HSEUiREG is always delivered for DIN-rail mount, the back-plate is an optional part that shall be mounted from the

customer. The threads from the DIN-rail mounting brackets shall be used. All screws are included into the Back-Plate Kit.)

[email protected]

www.powersolve.co.uk

020321

HSEUiREG07201(R2) MANUAL

Connections

Clamping Yoke Connector Specifications

Input / Output connections Signal connections plugs

Tightening torque min. – max. 1,2 – 2,2Nm (blade 1,0x5,5 DIN5264 ) 0,2 – 0,25Nm (blade 0,4x2,2 DIN5264)

Touch-safe protection acc. to DIN VDE 0470 IP20 plugged/ IP10 unplugged Not applicable

Clamping range, min. – max. 0,5 – 16mm² / AWG26 – AWG6 0,2 – 1,5mm² / AWG28 – AWG14

Solid, H05(07) V-U min. – max. 0,5 – 16mm² 0,2 – 1,5mm²

Stranded, H05(07) V-U min. – max. 6 – 16mm² 0,2 – 1,5mm²

Flexible, H05(07) V-U min. – max. 0,5 – 16mm² 0,2 – 1,5mm²

w. plastic collar ferrule, DIN 46228 pt 4 min. – max. 2,5 – 10mm² 0,2 – 1,5mm²

w. wire end ferrule, DIN 46228 pt 1, min. – max. 2,5 – 10mm² 0,2 – 1,5mm²

Plug gauge in accordance with EN 60999 a x b; ø 5,4 x 5,1mm; 5,3mm 2,4 x 1,5mm; 2,3mm

Pitch (P) 10,16mm 3,5mm

Wire Stripping Length (fine wired)

Nominal Cross Section Wire End Ferrule Stripping Length Wire End Ferrule Stripping Length

0,25mm² H0,25/5 5mm H0,25/10 HBL 8mm

0,5mm² H0,5/6 6mm H0,5/12 OR 8mm

1,0mm² H1,0/6 6mm H1,0/12 GE 8mm

2,5mm² H2,5/12 12mm H2,5/19D BL 14mm

4,0mm² H4,0/12 12mm H4,0/20 GDR 14mm

6,0mm² H6,0/20 12mm H6,0/20 SW 14mm

10,0mm² H10,0/12 12mm H10,0/22 EB 15mm

The length of ferrules is to be chosen depending on the rated voltage. The outside diameter of the plastic collar should not be larger than

the pitch (P)

Ordering Information

Ordering Codes

Product Code

Info

rmation

Article Number

HSEUiREG

.018

(R2)

18Vdc

304108

1CA

HSEUiREG0

01.030(R2)

30Vdc

304108

002CA

HSEUiREG0

01.050(R2)

0Vdc

304108

003CA

HSEUiREG

7201.060(R2)

60Vdc

3041084021CA

HSEUiREG0

01.090(R2)

90Vdc

304108

004CA

HSEUiREG0

01.130(R2)

130Vdc

304108

005CA

HSEUiREG0

01.180(R2)

180Vdc

304108

006CA

HSEUiREG0

01.240(R2)

240Vdc

304108

007CA

HSEUiREG

7201

.018PS(R2)