Powr-Flite PF56 User manual

OPERATOR’S MANUAL
PF56
Wet/Dry Vacuum
WARNING: OPERATOR MUST READ AND UNDERSTAND THIS MANUAL
COMPLETELY BEFORE OPERATING THIS EQUIPMENT.
PF56-Man 3/2009
©Tacony, Inc., All rights reserved
Equipment must be operated, serviced and maintained in accordance with the manufacturer’s instructions.

– 2 –
IMPORTANT SAFETY ADVICE
When using electrical equipment basic safety precautions should be fol-
lowed including the following:
You must have training in the operation of this machine before using it.
Read all instructions carefully before use.
●Keep children and unauthorized persons away from the machine
when in use.
●Do not leave the machine plugged in when not in use.
●Switch the machine off before removing the plug from the outlet.
●When unplugging, pull the plug, not the cord.
●The machine must be unplugged prior to cleaning or servicing
the machine
●Keep the power cord clear of moving parts.
●Do not run the machine over the power cord.
●Do not operate the machine with a damaged power cord or plug,
or if the machine malfunctions or is damaged in any way.
●Do not use where hazardous dust is present.
●Do not use in an explosive atmosphere.
●Do not use where flammable liquids or gasses are present.
●Do not use or pick up flammable chemicals or liquids with
this machine.
●Take care when using the machine near the top of stairs to avoid
overbalancing.
●Maintenance and repair must be done by authorized personnel only.
●Wear suitable footwear to avoid slipping.
●Do not operate this machine in bare feet or with open-toed shoes
or sandals.
●Do not smoke when using the machine.
●CAUTION:-This machine is for indoor use only and should not be
used or stored outdoors or in wet conditions.
DRY OPERATION OF VACUUM
The wet/dry vacuums are equipped with bypass motors. Install the cloth
filter, place the motor head on the canister and snap down the hold-down
clamps.
WET OPERATION OF VACUUM
The wet/dry vacuums are equipped with a bypass motor so that the work-
ing vacuum is separated from the cooling air flow. To pick up water, the
dry filters must be removed. The safety float assembly, located in the
vacuum head, stops the vacuum motor when water in the tank exceeds
the safety level.
After picking up aggressive or caustic liquids (floor stripper, oils, lubri-
cants, degreasers, etc.), thoroughly rinse the tank, hose, wand and tools.
Failure to properly clean these items will void the manufacturer’s war-
ranty.
WAND AND ATTACHMENT INSTRUCTIONS
To assemble the two piece wand:
1. Match the alignment ridges of the upper and lower wand sections.
2. Push the upper wand into the lower wand.
To assemble tools:
1. Slide the swivel cuff of the tool onto the tapered lower wand.
2. Turn swivel cuff 1/4 turn to tighten.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
*When using a wet/dry vacuum, basic precautions should be followed.
*Read all instructions before using your vacuum.

– 3 –
DRAINING
When the tank is full.
1. Release drain hose from hose clamp.
2. Remove plug from hose end to start draining process.
3. When draining is complete, replace hose plug and snap hose back
into clips on side of tank.
NOTE: When the water level in the tank exceeds the safety level, the
safety device will automatically block the inlet, and the motor turning
sound will be changed, but power will remain ON. The power must be
turned OFF before emptying the tank.
REMOVE THE PAPER FILTER
The paper filter must be removed for wet recovery.
Push the metal ping counterclockwise to release the filter.
Remove the paper filter.
HOSE ATTACHMENT INSTRUCTIONS
The hose and swivel connector are pre-assembled at the factory.
To attach the swivel connector to the intake fitting of the canister:
1. Push the grooved cuff straight into the intake fitting.
2. To remove, press the release button on top of the intake fitting
while pulling the grooved cuff out.
MAINTENANCE AND SERVICING
1. To dismantle, unclip both latches and remove top housing and filter
with frame.
2. Wash the filter with water and allow it to dry.
3. After washing, remove excess water with a gentle squeegee.
4. Replace the filter and top housing and fasten the latches.
NOTE: This cleaner is designed with a powerful suction. Do not be
alarmed if the motor noise increases when performing tougher
cleaning work.
Model PF56 drain hose.
Model PF56 shown with optional front mounted squeegee.

– 4 –
ref # item # description
1 WD20 HANDLE
2 WD66C POWER CORD
3 WD66 EXTENSION CORD
5 WD34 CORD PROTECTOR
6 WD65 TOP COVER
7 WD15W MOTOR CONNECTION WIRE
9 WD17 WIRE PLATE
10 WD16 MIDDLE SEAT
12 WD82 LOWER BASE BLOCK
13 WD83 TOP BLOCK
15 WD14B MOTOR SEAT
17 WD84 BLOCKER
19 WD53 GASKET
22 WD67 POWER SWITCH
23 WD206 CAPACITOR
24 WD207 TERMINAL BLOCK
27 WD15 MOTOR
ref # item # description
29 WD68 MOTOR GASKET
30 WD70 SPONGE
31 WD69 SQUARE SPONGE
32 WD85 REAR WHEEL PLATE
34 WD166 PLATE B
37 WD87 HOUSING BASE
38 WD201 GASKET
39 WD10 BASE COVER
41 WD165 GASKET
43 WD9 FLOAT
44 WD8 FRAME
46 WD37 SPRING
47 WD35 HOOK
48 WD36 PAPER FILTER
49 WD7 FILTER FRAME
50 WD3 FILTER ASSY
51 WD148 FABRIC
Model PF56 Parts
1
2
3
5
6
7
9
10
11
12
13
15
17
17
19
20
22
23
24
19
27
29
30
31
32
34
12
12
37
38
39
41
19
43
44
46
45
48
49
50
51
52
78
79
70
80
81
77
76
75
74
73
72
71
107
67
68
69
91
101
102
103
104
99
98
118
117
119
116
115
115
114
113
112
111
110
109
97
96
100
95
94
93
92
66
64
62
61
60
59
82
83
84
85
86
87
88
89
90
106
105

– 5 –
Model PF56 Parts
ref # item # description
1 WD219 TANK
2 WD220 NUT
3 WD221 NUT
4 WD132 HANDLE
5 WD133 COVER
6 WD222 WASHER
7 WD223 HOLDER
8 WD224 WASHER
9 WD121 HOLDER
10 WD128 CLIP BASE
11 WD44 NUT
12 WD63 CLIP
13 WD127 CLIP HOLDER
14 WD52 SPRING
15 WD129 PIN (SHORT)
16 WD131 PIN (LONG)
17 WD50 WASHER
18 WD45 SUCTION COUPLER
19 WD86 BUTTON FIXER
20 WD46 BUTTON
21 WD225 HOLDER
ref # item # description
22 WD226 HANDLE
23 WD227 AXEL
24 WD228 BUSHING
25 WD123M REAR WHEEL
26 WD229 WASHER
27 WD230 C-RING
28 WD167 FRAME
29 WD231M FRONT WHEEL
30 WD232 CLAMP
31 WD233 HOLDER
32 WD236 CAP
33 WD237 CONNECTOR B
34 WD146 HOOK
35 WD238 CLAMP
36 WD239 HOSE
37 WD240 PROTECTOR
38 WD241 CLAMP-2
39 WD242 SEAL HOLDER
40 WD188 INNER SEAL
41 WD243 OUTER SEAL
42 WD244 CONNECTOR A

1
2
3
5
6
7
9
10
11
12
13
15
17
17
19
20
22
23
24
19
27
29
30
31
32
34
12
12
37
38
39
41
19
43
44
46
45
48
49
50
51
52
78
79
70
80
81
77
76
75
74
73
72
71
107
67
68
69
91
101
102
103
104
99
98
118
117
119
116
115
115
114
113
112
111
110
109
97
96
100
95
94
93
92
66
64
62
61
60
59
82
83
84
85
86
87
88
89
90
106
105
Model PF56 Parts
ref # item # description
91 WD168 U-SHAFT
92 WD169 BUTTON
93 WD170 FIXED NUT
94 WD171 ADJUSTED WHEEL
95 WD172 BUTTON
96 WD173 WHEEL
97 WD174 SQUEEGEE BODY
98 WD175 BLADE BRACKET
99 WD176 BLADE
100 WD177 FIXED PLATE 2
101 WD179 PEDAL BRACKET
102 WD180 CONNECTOR
103 WD181 HOSE
104 WD182 BEND CONNECTOR
105 WD183 SEAL
ref # item # description
106 WD184 ADJUSTER LEVER
107 WD186 ADJUSTER LEVER KNOB
109 WD191 GASKET
110 WD24 CONNECTOR
111 WD25 HOSE
112 WD26 CONNECTOR
113 WD27 FIXER
114 WD28 BEND CONNECTOR
115 WD29 EXTENSION WAND
116 WD112 BRUSH NOZZLE ASS’Y
117 WD32 CREVICE TOOL
118 WD33 ROUND BRUSH
119 WD30A SQUEEGEE NOZZLE ASS’Y
WD157 DRAIN HOSE ASS’Y
FM100H FRONT MOUNTED SQUEEGEE ASS’Y
– 6 –

– 7 –
Model PF56 Parts - Optional Squeegee Assembly
Installing Instructions - FM100H
FRONT MOUNT SQUEEGEE INSTRUCTIONS
1. Remove vacuum head and filters from the vacuum.
2. Install axle mounting plate to bottom of unit. See fig 1
3. Attach handle bracket to squeegee bracket.
4. Attach squeegee bracket to the axle bracket. See fig 2
5. Attach handle to handle bracket. See fig 3
6. Attach handle holder to machine handle. See fig 4
7. Attach squeegee to squeegee bracket. See fig 5
8. Adjust compensating wheel as necessary.
1
2
3
4
5

3101 Wichita Court
Fort Worth, TX 76140
800.880.2913
www.Powr-Flite.com
The Powr-Flite Limited Warranty
The manufacturer warrants to the original purchaser that products manufactured are free from defects, provided such goods are
installed, operated and maintained in accordance with written manuals or other instructions for a period of 1 year from date of pur-
chase on workmanship, motor, and parts. In case you, as our customer, meet any trouble with your machine, contact a Powr-Flite
representative, who will be happy to be of service to you and will take care of any warranty issues.
Loss of Suction
CAUSE: SOLUTION:
1) Tank full. 1) Empty Tank
2) Dry filter assembly clogged. 2) Clean cloth filter.
3) Clogged hose or wand. 3) Remove obstruction.
4) Tank rim is dented. 4) Replace tank.
5) Loose or broken fan. 5) Contact manufacturer or service center.
6) Motor not working. 6) Contact manufacturer or service center.
7) Float not functioning. 7) Check to see if float moves freely or tank is full.
8) Seal worn. 8) Replace seal.
Motor is not running
CAUSE: SOLUTION:
1) Broken switch. 1) Contact manufacturer or service center.
2) Defective power cord. 2) Contact manufacturer or service center.
3) Defective motor. 3) Contact manufacturer or service center.
Dust blowing from unit when running
CAUSE: SOLUTION:
1) Cloth filter dirty. 1) Clean cloth filter.
2) Cloth filter is torn. 2) Replace filter.
3) Cloth filter is not installed. 3) Install cloth filter, when vacuuming very fine dust,
Water blowing from unit when running
CAUSE: SOLUTION:
1) Tank is full of liquid. 1) Empty tank.
2) Sudsy or foamy liquid is being picked up. 2) Add defoamer to tank.
TROUBLE SHOOTING GUIDE