Precision Digital Corporation PDW30-RNA User manual

PDW30 & PDW90 Repeater Field Unit
Instruction Manual
PRECISION DIGITAL CORPORATION
233 South Street • Hopkinton MA 01748 USA
Tel [phone] • Fax [phone]
www.predig.com
•Wireless Repeater Unit in a Rugged, Industrial Housing
•Simple to Order, Configure, & Install
•Increase Range an Additional 1 Mile Line-of-Sight, 500 Ft Indoor
•Remote or Attached Antenna
•Flanges for Wall or Pipe Mounting
•Software Available for Even Easier Setup
•Rugged, IP68, NEMA 4X Enclosure
•3-Year Warranty

PDW30 & PDW90 Repeater Field Unit Instruction Manual
2
Disclaimer
The information contained in this document is
subject to change without notice. Precision Digital
Corporation makes no representations or
warranties with respect to the contents hereof;
and specifically disclaims any implied warranties
of merchantability or fitness for a particular
purpose.
•Read complete instructions prior to installation
and operation of the device.
•Risk of electric shock or personal injury.
•This product is not recommended for life support
applications or applications where malfunctioning
could result in personal injury or property loss.
Anyone using this product for such applications
does so at their own risk. Precision Digital
Corporation shall not be held liable for damages
resulting from such improper use.
•Failure to follow installation guidelines could
result in death or serious injury. Make sure only
qualified personnel perform the installation.
WARNING
Cancer and Reproductive Harm - www.P65Warnings.ca.gov
Limited Warranty
Precision Digital Corporation warrants this
product against defects in material or
workmanship for the specified period under
“Specifications” from the date of shipment from
the factory. Precision Digital’s liability under this
limited warranty shall not exceed the purchase
value, repair, or replacement of the defective unit.
See Warranty Information and Terms &
Conditions on www.predig.com for complete
details.
Registered Trademarks
Modbus®is a registered trademark of Schneider
Electric. All other trademarks mentioned in this
document are the property of their respective
owners.
© 2020 Precision Digital Corporation.
All rights reserved.
Introduction
Precision Digital PDW30-RNA wireless signal repeat-
ers are used to retransmit wireless signals when con-
nectivity between PDW30 or PDW90 wireless units is
an issue. They are incredibly simple to install as they
only require power and a network ID. Any units in
range of the repeater with the same network ID will
retransmit through it, thus increasing signal strength.
Use repeaters to broadcast over very long distances
or around permanent obstacles.
Ordering Information
Model Description
PDW30-RNA PDW30 & PDW90 Repeater Field Unit
Accessories
Model
Description
PDA10 PDW Wireless Signal Strength Survey
Tool
PDA3120-S RP-SMA M/F Antenna Cable 20ft
PDA3140-S RP-SMA M/F Antenna Cable 40ft
PDA3120-N RP-SMA F to N Male Antenna Cable
20ft
PDA3140-N RP-SMA F to N Male Antenna Cable
40ft
PDA3900-12-N PDW 900 MHz Antenna, 1/2" NPT
PDA3900-6Y-N Yagi Antenna 6dB
PDA3900-9Y-N Yagi Antenna 9dB
PDA6963-SS Stainless Steel PDW30 Mounting Kit

PDW30 & PDW90 Repeater Field Unit Instruction Manual
3
Table of Contents
Introduction......................................................................................................... 2
Ordering Information.......................................................................................... 2
Specifications ..................................................................................................... 4
General............................................................................................................ 4
Wireless Radio ............................................................................................... 4
PDW Manager Software ................................................................................. 4
Safety Information .............................................................................................. 5
Installation........................................................................................................... 5
Unpacking....................................................................................................... 5
Pre-Installed Conduit Plug ............................................................................ 5
Mounting Instructions.................................................................................... 5
Cover Jam Screw ........................................................................................... 5
FCC Notice...................................................................................................... 5
Canada (IC) Notice ...................................................................................... 6
PDA6963-SS Stainless Steel Pipe Mounting Kit .......................................... 6
Mounting Dimensions ........................................................................................ 6
Connections........................................................................................................ 7
Wiring Diagram............................................................................................... 7
Power Connector ......................................................................................... 7
Setup and Programming.................................................................................... 8
Overview ......................................................................................................... 8
Buttons & Display .......................................................................................... 8
Programming Buttons ................................................................................... 8
PDW Manager Software ................................................................................. 9
Setup Menu..................................................................................................... 9
Entering Numeric Values ............................................................................. 9
Network ID ................................................................................................... 9
Password Setup......................................................................................... 10
Restore Defaults ........................................................................................ 10
Programming with PDW Manager............................................................... 11
Table of Figures
Figure 1. PDA6963-SS Stainless Steel Pipe Mounting Kit ................................ 6
Figure 2. Enclosure Dimensions – Front View................................................... 6
Figure 3. Enclosure Dimensions – Side Cross Section View ........................... 6
Figure 4. PDW30-RNA Device Assembly, Rear View......................................... 7
Figure 5. Power Connections .............................................................................. 7

PDW30 & PDW90 Repeater Field Unit Instruction Manual
4
Specifications
Except where noted all specifications apply to operation at +25°C.
General
Display 32-character dual-line alphanumeric dot
matrix LCD display with backlight
(4.68mm x 2.21mm characters)
Display
Orientation
Display may be mounted at 180° from
default orientation
Network ID
Field selectable: 0 - 99
Programming
Methods
Four programming buttons (behind glass) or
PC with PDW Manager software.
Password A programmable password restricts
modification of programmed settings.
Power 12-28 VDC, 5 W max
Non-Volatile
Memory
All programmed settings are stored in non-
volatile memory for a minimum of ten
years if power is lost.
Isolation 500 V
Environmental Operating temperature range: -40 to 65°C;
(display inoperable < -20 °C);
Storage temperature range: -40 to 85°C;
Relative humidity: 0 to 90% non-
condensing
Connections Removable screw terminal blocks accept
16 to 30 AWG wire.
Enclosure Cast aluminum with glass window, 0.30%
max copper content, corrosion resistant
powder coating, color: blue. NEMA
4X/IP68. Two ½" NPT threaded conduit
openings. One ½" NPT stainless steel
conduit plug with 10 mm hex key fitting
installed.
Mounting May be mounted directly to conduit. Two
mounting holes for 1.5" pipe or wall
mounting. See Mounting Dimensions on
page 6for mounting space requirements.
Tightening
Torque
2.5 lb-in (0.28 Nm)
Shipping
Dimensions
17" x 14" x 9" (43.2 cm x 35.6 cm x 22.9 cm)
(L x W X H)
Shipping
Weight
5 lbs. (2.27 kg)
Warranty 3 year parts and labor. See Warranty
Information and Terms & Conditions on
www.predig.com for complete details.
Wireless Radio
Frequency
900 MHz
Range
500 ft (152.4 m) indoor, 1 mi (1.61 km)
outdoor (line-of-sight)
Encryption
AES 128-bit encryption available using
PDW Manager software
Interference
Reduction
Frequency Hopping Spread Spectrum
(FHSS)
Power Output
24 dBm (250 mW)
Sensitivity -101 dBm
PDW Manager Software
System
Requirements
Microsoft®Windows®XP/Vista/7/8/10
Communications
USB 2.0 (Standard USB A to Micro
USB B)
Configuration
Configure devices one at a time

PDW30 & PDW90 Repeater Field Unit Instruction Manual
5
Safety Information
•Read complete instructions prior to installation
and operation of the device.
•Read all product labels completely and follow all
instructions and requirements listed on the labels
for installation or service.
•Installation and service should be performed only
by trained service personnel. Service requiring
replacement of internal components must be
performed at the factory.
Installation
All pushbuttons and wiring connectors are accessed
by opening the enclosure. To access electrical con-
nectors, remove the 2 captive screws and remove the
display assembly. Pushbuttons may also be accessed
using the magnet assembly if reed switches are in-
stalled.
Unpacking
Remove both units from box. Inspect the packaging
and contents for damage. Report damages, if any, to
the carrier. If any part is missing or the units malfunc-
tion, please contact your supplier or the factory for as-
sistance.
Pre-Installed Conduit Plug
The PDW30-RNA is supplied with one pre-installed
optional conduit plug for installations that do not re-
quire the use of both conduit entries. The conduit plug
includes an internal hexagonal socket recess for re-
moval.
Mounting Instructions
The PDW30-RNA has two mounting holes that may
be used for a 1.5" pipe mounting or wall mounting.
Alternatively, the unit may be supported by the con-
duit using the conduit holes provided. The antenna is
threaded into one of the three conduit holes and may
be moved as appropriate for the installation.
It can also be mounted by using the PDA6963 mount-
ing bracket in order to orient the device antenna away
from the pipe. Refer to Mounting Dimensions on page
6for details on wall or panel space requirements.
Cover Jam Screw
The cover jam screw should be properly installed
once the wireless units have been wired and tested in
a safe environment. The cover jam screw is intended
to prevent the removal of the units’ cover while in op-
eration without the use of tools. Using a M2 hex
wrench, turn the screw clockwise until the screw con-
tacts the unit. Turn the screw an additional 1/4 to 1/2
turn to secure the cover.
•Excess torque may damage the threads and/or
wrench.
FCC Notice
Contains FCC ID: MCQ-XB900HP
The enclosed device complies with Part 15 of the
FCC Rules. Operation is subject to the following two
conditions: (i.) this device may not cause harmful in-
terference and (ii.) this device must accept any inter-
ference received, including interference that may
cause undesired operation.

PDW30 & PDW90 Repeater Field Unit Instruction Manual
6
•The RF module has been certified for remote and
base radio applications. If the module will be used
for portable applications, the device must undergo
SAR testing. This equipment has been tested and
found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment generates,
uses and can radiate radio frequency energy and,
if not installed and used in accordance with the
instructions, may cause harmful interference to
radio communications. However, there is no
guarantee that interference will not occur in a
particular installation.
•If this equipment does cause harmful interference
to radio or television reception, which can be
determined by turning the equipment off and on,
the user is encouraged to try to correct the
interference by one or more of the following
measures: Re-orient or relocate the receiving
antenna, Increase the separation between the
equipment and receiver. Connect equipment and
receiver to outlets on different circuits or consult
the dealer or an experienced radio/TV technician
for help.
Canada (IC) Notice
Contains Model: XB900HP, IC: 1846A-XB900HP
Integrator is responsible for its product to comply with
IC ICES-003 & FCC Part 15, Sub. B - Unintentional
Radiators. ICES-003 is the same as FCC Part 15
Sub. B and Industry Canada accepts FCC test
report or CISPR 22 test report for compliance with
ICES-003.
PDA6963-SS Stainless Steel
Pipe Mounting Kit
Figure 1. PDA6963-SS Stainless Steel Pipe Mounting Kit
Mounting Dimensions
All units: inches [mm]
Figure 2. Enclosure Dimensions – Front View
Figure 3. Enclosure Dimensions –
Side Cross Section View
Note: The supplied conduit plug may extend up to
0.6 in [15 mm] from the conduit opening when installed.

PDW30 & PDW90 Repeater Field Unit Instruction Manual
7
Connections
To access the power connector, remove the enclo-
sure cover and unscrew the two captive stainless
steel screws. Remove the electronics assembly from
the enclosure. The power connection is made to a two
terminal removable connector on the back of the as-
sembly. Grounding connections are made to the two
ground screws provided on the base – one internal
and one external.
•Static electricity can damage sensitive
components.
•Observe safe handling precautions for static-
sensitive components.
•Use proper grounding procedures/codes.
•Observe all safety regulations. Electrical wiring
should be performed in accordance with all
agency requirements and applicable national,
state, and local codes to prevent damage to the
device and ensure personnel safety.
Figure 4below shows the locations of screw terminal
blocks on the rear of the wireless unit assembly.
Note: Digital I/O, Modbus, and Signal connections are
not used with the repeater unit.
Figure 4. PDW30-RNA Device Assembly, Rear View
Wiring Diagram
Power Connector
Power connections are made to a two-terminal con-
nector labeled POWER in Figure 4. The PDW30-RNA
is reverse polarity protected; it will not be damaged if
wired backward.
Make sure that the power supply can provide between
12 and 28 VDC to the wireless device.
Figure 5. Power Connections

PDW30 & PDW90 Repeater Field Unit Instruction Manual
8
Setup and Programming
Overview
There are no jumpers to set for wireless device input
selection.
Setup and programming is done through the program-
ming buttons located underneath the enclosure cover
or using the PDW Manager software. After power and
input signal connections have been completed and
verified, apply power to the device.
Buttons & Display
Display for PDW30-RNA Repeater Unit
Programming Buttons
The units can be programmed using the buttons lo-
cated behind the enclosure cover. Use the Menu but-
ton to enter or exit programming mode, the Next but-
ton to cycle forward through menu options, the Previ-
ous button to cycle backward through menu options,
and the Enter button to select the menu item or option
you want.
During number entry, use the Next button to select a
digit and the Previous button to increment the se-
lected digit.
Button/Symbol
Description
Menu
Enter or exit the device menu
Enter
Select a menu item of option
Previous
Cycle backward through menus or
increment digit
Next
Cycle forward through menus or
select next digit
Display
Status
RSSI
Received Signal Strength
Indicator
Indicates the wireless signal
strength between wireless devices
on a scale of 1 to 10. If the repeater
is used in a PDW90 installation, this
value represents the signal strength
between the base station and the
repeater. If the repeater is used in a
PDW30 installation, this value
represents the signal strength
between the primary unit and the
repeater.
RT
Receiving/Transmitting
Flashes while the devices are
sending and/or receiving data
REP
Repeater
Indicates that the device is a
repeater unit. This distinction is
fixed and cannot be changed.

PDW30 & PDW90 Repeater Field Unit Instruction Manual
9
PDW Manager Software
The units can also be programmed using the PC
based PDW Manager. Units connect to a PC via the
micro USB connection on their face, underneath the
enclosure cover.
Use of PDW Manager is required for programming
advanced settings, such as wireless encryption.
Note: Units must be powered externally prior to
programming via USB.
PDW Manager is available on the included CD or
online at www.predig.com/pdwmanager.
Instructions on the use of PDW Manager to program
the PDW30-RNA wireless units can be found under
Programming with PDW Manager on page 11.
Setup Menu
The setup menu consists of network ID, password,
and factory defaults restoration.
Entering Numeric Values
Numeric values are set using the Next and Previous
buttons. Press Next to select next digit and Previous
to increment digit value.
The selected digit will flash.
Press the Enter button, at any time, to accept the
value or the Menu button to exit without saving.
Network ID
The network ID determines with which wireless de-
vices the repeater will connect. The repeater unit
must share the same network ID as the other wireless
devices in order to communicate with them.
NOW: 01
NETWORK ID
SET: 01
NETWORK ID
increments selected digit.
selects next digit to the right

PDW30 & PDW90 Repeater Field Unit Instruction Manual
10
Password Setup
The wireless repeater may be protected with a four
digit numeric password in order to prevent unauthor-
ized tampering. When a password has been set, you
will be prompted to enter that password in order to ac-
cess the device menu.
To disable password protection, simply enter 0000 as
the password.
Note: See Entering Numeric Values on page 9 for
instructions on how to enter numbers
Making Changes to a Password
Protected Repeater
Once a password has been set on the device, you will
be required to enter that password before being al-
lowed to access the device menu.
Note: Setting a password will require you to enter the password
to access the device settings via the PC software as well.
Did you forget the password?
The password may be disabled by entering a master
password. If you are authorized to make changes,
enter the master password 7300 to unlock the device.
Restore Defaults
If a mistake has been made while programming the
wireless repeater device, and it is unclear where the
error occurred, the best option may be to perform a
factory reset of the device and begin again.
SETUP
PASSWORD
NOW: 0000
PASSWORD (0=OFF)
SETUP MENU
BACK TO
SET: 0123
PASSWORD (0=OFF)
increments selected digit.
selects next digit to the right
0000 disables the password.

PDW30 & PDW90 Repeater Field Unit Instruction Manual
11
Programming with PDW Manager
PDW Manager allows you to program the PDW30-RNA wireless repeater unit from a PC with a USB connection. The
unit connects to a PC via the micro USB connection on its face, underneath the enclosure cover. Use of PDW Man-
ager is required for programming advanced settings such as wireless encryption.
PDW Manager can be found on the included CD or downloaded from www.predig.com/pdwmanager. Once the soft-
ware is running, power the unit using a 12-28 VDC power supply and connect the device to the PC using the provided
USB cable.
The PC will automatically install the appropriate device drivers. Once this has completed, the device will appear in the
Device list at the top of the PDW Manager window. Click Connect.
The image below shows the available options on the configuration tab while the repeater unit is connected.
Note: The two calibration tabs and the IO Testing tab are not applicable to the repeater unit.

PDW30 & PDW90 Repeater Field Unit Instruction Manual
12
Device communication can be secured by enabling 128-bit AES encryption. A channel mask may also be set for
interference immunity. The encryption key and channel mask may be entered on the Advanced tab.
Once you have entered the encryption information, click Save Settings. The wireless devices must share identical
encryption keys in order to communicate, so be sure to enter the same information for the second unit.

PDW30 & PDW90 Repeater Field Unit Instruction Manual
PRECISION DIGITAL CORPORATION
233 South Street • Hopkinton MA 01748 USA
Tel [phone] • Fax [phone]
www.predig.com
LIMW30R_C
SFT102 Ver 1.000 & up
06/20
Contact Precision Digital
Technical Support
Call: [phone] or [phone]
Fax: [phone]
Email: [email protected]
Sales Support
Call: [phone] or [phone]
Fax: [phone]
Email: [email protected]
Place Orders
Email: [email protected]
For the latest version of this manual please visit
www.predig.com