Precision Power SEDONA SN.10 User manual

2012 SEDONA
SUBWOOFERS
SN.8 SN.10 SN.12

Thank you for choosing PrecisionPower woofers. Designed and engi-
neered in the USA, this product combines innovative technology with
the finest materials to consistently deliver Absolutely State of the Art
performance, sound quality, reliability, and value. This PrecisionPower
product reflects our commitment to offer you unparalleled perfor-
mance and quality for years of dependable service and listening en-
joyment.
Polly Cone
Rubber Surround
2.0” 4-layer VC on Aluminum Former
Nickel Plated 8ga. Compression Terminals
Woven tinsle leads
Die-Cast Aluminum Frame
Vented T-Yoke Back-plate
Polly Conical Cone Dust-cap
Poly-Cotton Suspension Spiders
Features, Parameters, & Dimensions
www.PrecisionPower.com
Impedance 4ohm 4ohm 4ohm
Re4.0284 4.6348 4.0425
Fshz47.42 34.65 33.09
Qes 0.8296 0.9681 0.6732
Qms 4.6253 3.4605 5.0576
Qts 0.7034 0.7565 0.5941
Lemh 2.4861 2.4719 2.5442
dIameteR 8 10 12
sd50.2655 In^2 78.5398 In^2 113.0973 In^2
Vas L 91.4366 121.5395 214.9423
BL11.19 8.12 10.07
mms 86.5542 63.2911 81.3553
sen dB 85.7 88.9 92.3
Rms/max 240/600 360/900 500/1200
mountIng depth 4Inch 4.5Inch 5 3/8 Inch
cutout dIam. 7.7Inch 9.6Inch 11.6Inch
sn.8 sn.10 sn.12

Enclosure Construction
Enclosure Dimensions
Enclosure Recommendations
www.PrecisionPower.com
Included in this manual are a number of different enclosure sugges-
tions. These are by no means the only enclosures to use, but they
provide a starting point to determine the correct enclosure for your
needs many factors must be addressed (amount of power, vehicle,
placement, crossovers, etc) Therefore, as always, PrecisionPower
recommends that your subwoofer be installed by an authorized Pre-
cisionPower dealer.
All enclosures should be made of .75” (3/4”) material only. When pos-
sible, make the baffle 1.5” (1 ½) thick and add .75” (3/4”) to the depth
of the enclosure to compensate. All volumes INCLUDE vent/port and
subwoofer displacements. DO NOT change the volume unless you
plan on adding a substantial amount of bracing. For added per-
formance, applying a coat of fiberglass resin to the interior walls will
greatly improve sealing the enclosure. Adding a thin layer of poly-fill
will improve response by smoothing out reflections within the enclo-
sure.
seaLed sn.8 sn.10 sn.12
mInImum .45 cu Ft. .75 cu Ft. 1.0 cu Ft.
optImum .75 cu Ft. 1.0 cu Ft. 1.25 cu Ft.
poRted
mInImum .75 cu Ft. 1 cu Ft. 1.5 cu Ft.
poRt WxL 4Inch x7.5Inch 3Inch x4.5Inch 5Inch x4.5 Inch
F3 hz48 40 55
optImum 1.0 cu Ft. 1.5 cu Ft. 2.0 cu Ft.
poRt WxL 4Inch x6.35Inch 4Inch x8.5Inch 5Inch x4Inch
F3 hz42 38 45