Premier Mounts LPWS100 User manual

LPWS100/LPWS200
Installation Instructions Page 1
9533-100-001-00
Step 1. Determine where the shelf will
be installed on the wall.
Step 2. Useastudfindertolocatethewallstud.
Step 3. Use a pencil to mark where the
stud is located.
Wood Stud Installation
LPWS100/LPWS200 Shelf Installation Instructions
Installation Tools (not supplied)
Screwdriver
1/8” Drill Bit Electronic
Stud Finder Drill LevelHammer Pencil
1/4” Drill Bit
Mounting Column
Glass Shelf Wall Anchors
Wood Screws
Flat Head
Screws (Qty 2)
Phillips Head Screw (Qty2)
Flat Washers (Qty 2) M3 Allen Wrench
Step 4. Place the mounting column over the
located wall stud.
Step 5. Level the mounting column.
Step 6. Use a pencil to mark the mounting
locations(twomarksfortheLPWS100
and four marks for the LPWS200
mounting locations).
Step 7. Use a 1/8” drill bit and drill to
pre-drill the mounting holes at the
marked locations.
Step 8. Place the mounting column against
the wall and align the mounting points
on the shelf mount with the pre-drilled
mounting holes.
Step 9. Insert and tighten the screws and
re-level the mounting column to
verify the position.
Stud Finder
Mounting
Column
Mounting
Location Mark
Drill
Step 6. Place the mounting column against
the wall and align the mounting points
on the shelf mount with the wall
anchor holes.
Step 7. Level the mounting column.
Step 8. Insert and tighten the screws and
re-level the mounting column to
verify the position.
Mounting
Column
Mounting
Location Mark
Drill
Step 5. Once the mounting holes have been
drilled, insert the wall anchors by
gently pressing the wall anchors into
place.
Level
Mounting
Column
Mounting
Location Mark
Step 1. Determine where the shelf mount will
be installed on the wall.
Step 2. Place the mounting column flat
against the wall. Make sure the
mounting column is level.
Step 3. Use a pencil to mark the holes where
the mounting column will be located.
Solid Surface Installation
Shelf Mounting Bracket
Glass Shelf
Cap Screw (Qty 1)
Column End Caps
(Qty 2)
Inserting Wall
Anchor
Gently Press
into Place
Wall Anchor
LPWS100
LPWS200
LPWS100 -
(Qty 1)
LPWS200 -
(Qty 2)
LPWS100 -
(Qty 1)
LPWS200 -
(Qty 2)
LPWS100 -
(Qty 2)
LPWS200 -
(Qty 4)
LPWS100 -
(Qty 2)
LPWS200 -
(Qty 4)
Level
Mounting
Column
Mounting
Location Mark
Neck Knuckle (Qty 1)
Step 4. Use a 1/4” drill bit and drill to
pre-drill the mounting holes.
Wall Anchor

Page 2 Installation Instructions
LPWS100/LPWS200
Neck Knuckle Assembly
Shelf Installation
Step 1. Align the neck knuckle on the glass
shelf with the slide channel on the
mounting column.
Step 2. Once aligned, slide the glass shelf
down (doing so while holding the
glass shelf at a 45° angle).
Step 3. When the desired height setting has
been achieved, slowly let the glass
shelf rest forward to a level position
and “click” into place.
Step 4. Use an M3 Allen wrench (supplied)
to tighten the locking screw. Do not
over-tighten this screw.
Locking Screw
Slide
Channel
Neck
Knuckle
Glass
Shelf
M3 Allen
Wrench
Shelf Installation Cable Management
Step 1. Place the end caps over the upper and
lower ends of the mounting column
and press these end caps firmly into
place.
Mounting
Column
End
Cap
Mounting
Points
Shelf Mounting
Bracket
Step 1. Place the glass shelf on a soft, flat surface
(reflective-side down).
Step 2. Place the shelf mounting bracket on the
three mounting points (see above).
Threaded Stud
Glass Shelf
Cap Screw
Step 4. Turn the glass shelf over (reflective-side
up).
Inthecenterofthemountingpointthereisa
threaded shaft. In order to attach the glass
shelf cap screw, the threaded shaft must
be inthe exact center position of the
mounting point.
Glass Shelf
(Reflective-side up)
Glass Shelf
(Reflective-side down)
Step 5. Slowly turn and tighten the glass shelf
cap screw onto the threaded shaft. Do not
over-tighten the glass shelf cap screw.
Step 1. Align the cables on either side of
the mounting column.
Mounting
Column
Cables
Plastic
Tabs
Cables
Shelf Assembly
Step 1. Place the mounting shelf bracket and the
neck knuckle together and align the
mounting holes to the mounting points.
Step 3. Using a screwdriver, insert and tighten
two (2) screws and two (2) flat washers
(supplied). Do not over-tighten these
screws.
Step 2. Insert and tighten two (2) Phillips flat
head screws.
Screwdriver
Screw and
Flat Washer
Step 2. Once the cables have been
aligned, gently tuck the cables
into the mounting column.
The plastic tabs will hold the cables
in place once they have been tucked
completely into the mounting
column.
Shelf Mounting
Bracket
Neck Knuckle
Mounting
Points
Mounting Holes
Screwdriver
Phillips Flat
Head Screw