Premier Mounts LMV User manual

9541-000-001-0X v6.1 publ. 11/12/18
INSTALLATION GUIDE
Press and Release ™ Pop Out Mount
LMV
premiermounts.com | p. 800.368.9700 | e. [email protected]
500 W Central Ave, Suite A, Brea, CA 92821 USA

5/16” x 3” Lag Bolts
(Qty 4)
Thread Depth Indicator
(Qty 1)
Universal Spacers
(Qty 8)
Finned Anchors
(Qty 4)
5/16” Flat Washers
(Qty 4)
Universal Washers
(Qty 4)
Pencil Protective Eyewear
Electronic Stud Finder M6 or 1/4” Drill Bit 3/8” Masonry Drill Bit
Portable DrillPhillips Head Screwdriver Socket Wrench
13mm or 1/2” Socket
Level
M5 Allen Driver
(Qty 1)
M4 x 12mm (Qty 4)
M4 x 16mm (Qty 4)
M4 x 25mm (Qty 4)
M6 x 12mm (Qty 4)
M6 x 16mm (Qty 4)
M6 x 25mm (Qty 4)
M8 x 12mm (Qty 4)
M8 x 16mm (Qty 4)
M8 x 25mm (Qty 4)
Wall Mount
(Qty 1)
Bracket
(Qty 1 Pair)
Included Components
Required for installation
Maximum Flat Panel Weight:
160 lb. / 72.57 kg.
Installation Guide
LMV
Page 2 premiermounts.com | p. 800.368.9700 | e. [email protected]

1
3
2
4
1.
the vicinity of the mount.
2. Use a pencil to mark each of the wall studs.
Wood Stud Installation
Use a pencil to mark the upper right mounting location
of the wall stud.
Drill a pilot hole using a M6 or 1/4” drill bit on the
stud that was marked on the upper right.
1. Place the mount against the wall and align it
with the pilot hole.
2. Insert one (1) 5/16” x 3” lag bolt one (1) 5/16”
washer into the upper right pilot hole.
3. Use a socket wrench and a 1/2” socket to
tighten the lag bolt.
4. Do not over tighten the lag bolt.
Installation Guide
LMV
Page 3
premiermounts.com | p. 800.368.9700 | e. [email protected]

5
7
6
1. Level the mount
2. Use a pencil to mark the remaining three (3)
mounting locations
1. Insert one (1) 5/16” x 3” lag bolt and one (1) 5/16”
washer into each pilot hole.
2. Tighten all lag bolts using a socket wrench and
1/2” socket.
3. Do not over tighten the lag bolts
Drill a pilot hole in each of the three (3) marks with a
power drill and a M6 or 1/4” drill bit.
2
3
1
2
3
1
Installation Guide
LMV
Page 4 premiermounts.com | p. 800.368.9700 | e. [email protected]

10
9
8
11
Two people recommended for this step; one person
to level the mount and another person to mark the
mounting locations.
Drill a pilot hole in each of the four (4) mark areas
with a 3/8” masonry drill bit.
Insert the Finned anchors into each pilot holes.
Lightly tap each Finned anchors into place with a
hammer.
1. Insert one (1) 5/16” x 3” Lag Bolt and one (1) 5/16”
washer into each pilot holes.
2. Tighten all lag bolts using a socket wrench and
1/2” socket.
Concrete Wall Installation
3
4
1
2
3
4
1
2
Installation Guide
LMV
Page 5
premiermounts.com | p. 800.368.9700 | e. [email protected]

Use commercially available hardware to secure the spacer.
Utilize the same spacer for multiple LMV installations.
For illustration only. LMV Spacer will vary.
Simply repeat step one when installing each of the surrounding
LMV mounts. Use one spacer for each 2x2 installation by mounting
it to the wall, or utilize the same spacer as many times needed to
complete an unlimited LMV large matrix video wall.
1. Plumb and level and mark each corner where the LMV will be
mounted (or secure to the wall).
2. Install the second mount working in a horizontal direction.
3. Square, Level, and Plumb.
4. Repeat this step for each mount horizontally
1) Mount the LMV to the desired location.
2) Align and Level the spacer to the corner register tabs
of the mount.
Level
For ease of installation
installation tim on large video wall array. Contact Customer
Installation Guide
LMV
Page 6
12
14
13
premiermounts.com | p. 800.368.9700 | e. [email protected]

1) Insert a small straw or toothpick into the threaded inserts found
2) Use a pencil to mark the depth of the threaded insert on the
small straw or toothpick.
3) Mark the straw or toothpick 1/8” above the depth of the
threaded insert, as shown in Figure 1.
4) Insert the small straw or toothpick into the remaining threaded
inserts to compare and verify their depth using the straw or
toothpick’s 1/8” allowance mark.
5) Locate the correct diameter screw for the threaded insert.
If the selected screw is longer than the 1/8” allowance mark
on the small straw or toothpick, as shown in Figure 2 and
Figure 3, do not use this screw. The screw length must not
bypass the mark.
6) Test each size of the screws provided.
The correct screws should thread easily into the mounting
point and not pull out when tension is applied.
Small Straw or Toothpick
Marking the 1/8”
Allowance
Small Straw
or Toothpick
Small Straw
or Toothpick Depth Plus 1/8” Allowance
Mark
Depth Plus 1/8” Allowance
Mark
Selecting the Mounting Hardware
Installation Guide
LMV
Page 7
15
premiermounts.com | p. 800.368.9700 | e. [email protected]

Universal Spacer Installation
Flat Panel
Universal Washer
Universal Spacer
Mounting Bracket
Mount Point
Mounting Screw
1)
2) Identify the number and location of the thread inserts on the
3) Aligning the holes on each mounting bracket with the thread
4)
minimum of two (2) screws per bracket.
Do not over tighten the mounting hardware.
Make sure the directional arrows on the mounting brackets
are facing up.
Universal Washer Installation
M8
M5, M6
M4
Universal Washers are designed to accommodate the various
17
Installation Guide
LMV
Page 8
Universal Spacers allow the user to attach the mounting bracket
Universal Spacer adds 1/4” to the distance between the mounting
The Universal Spacers must be stacked and oriented as
shown.
The Universal Spacers must only be installed between the
16
premiermounts.com | p. 800.368.9700 | e. [email protected]

Mounting bracket adjustments are factory pre-set (see Note).
This section requires two people.
bottom hooks of both mounting brackets are securely seated
on the upper and lower mounting rails of the wall panel.
1)
wall panel.
2)
3) Engage the top and bottom mounting brackets to the rails of the
mount.
Note: These registers must
align prior to installation.
They are factory set.
Check to determine proper
alignment
Attaching the Flat-Panel to the Mount
being accidently dislodged from the LMV.
1) Locate the pre-installed security locking safety screw at
the bottom of each of the mounting brackets.
2) Use the M5 Allen driver (supplied) to tighten the locking
safety screw.
Locking Safety Screw Installation
Do not overtighten the locking safety screws.
Note: Tighten screw to surface, then tighten 1/4” turn
Pre-installed
Locking Safety Screw
( 1 per Bracket )
18
19
ONLY TIGHTEN AFTER
FINAL ADJUSTMENT
Installation Guide
LMV
Page 9
premiermounts.com | p. 800.368.9700 | e. [email protected]

Left
Control
Right
Control
TOP
BOTTOM
Left
Control
TOP
BOTTOM
TOP
BOTTOM
TOP
BOTTOM
Right
Control
TILT DOWN
TILT UP
MOVE OUTWARD
MOVE INWARD
TOP
BOTTOM
TOP
BOTTOM
TOP
BOTTOM
TOP
BOTTOM
TOP TOP
BOTTOM BOTTOM
TOP TOP
BOTTOM BOTTOM
AND/
OR
AND/
OR
Installation Guide
LMV
Page 10 premiermounts.com | p. 800.368.9700 | e. [email protected]

LEVEL LEVEL
Left
Control
Right
Control
LEVEL
Left
Control
Right
Control
LEVEL
LEVEL
Left
Control
Right
Control
LEVEL
LEVEL
Left
Control
Right
Control
LEVEL
ROTATE RIGHT
ROTATE LEFT
LEVEL DOWN
LEVEL UP
Installation Guide
LMV
Page 11
premiermounts.com | p. 800.368.9700 | e. [email protected]

1. Swipe GAPit along vertical gap
2. Inspect for .050” gap & adjust if
needed
3. Swipe GAPit along horizontal gap
4. Inspect for .050” gap & adjust if
needed
Damage happens when weight is transferred to the ultra-thin bezels of video wall installations,
This results inimage distortion, and costly repairs and replacement
Use the GAPit GO/No Go Gauge (supplied with model specific spacer) as a final step in the process
to inspect and adjust the gap to prevent costly replacement and extend the lifespan of the displays.
20
Installation Guide
LMV
Page 12 premiermounts.com | p. 800.368.9700 | e. [email protected]

Installation Guide
LMV
Page 13
Servicing
1. Push evenly in the front of the LMV to release the
single latch spring lock (Figure 1).
2. Slowly pull the front of the LMV to extend the scissor
arms (Figure 2).
3. Loosen the locking safety screws on both mounting
brackets.
4.
kickstands against the bottom tubing of the mount
(Figures 2 & 3).
5. Perform any neccessary repairs. Close the latch
after servicing.
Figure 3
Figure 1
Figure 2
Single Latch Spring Lock
21
premiermounts.com | p. 800.368.9700 | e. [email protected]

Premier Mounts intends to make this manual accurate and complete. However, Premier Mounts makes no claim that the information
contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with
the installation or use of this product. The information contained in this document is subject to change without notice or obligation of
any kind. Premier Mounts makes no representation of warranty, expressed or implied, regarding the information contained herein.
PREMIER MOUNTS
LIMITED LIFETIME WARRANTY
What and Who is Covered by this Limited Lifetime Warranty
Premier Mounts warrants all mounting products to be free from defects in material and workmanship
for the lifetime of the original installation of the product.
What Premier Mounts Will Do
At the sole option of Premier Mounts, Premier Mounts will repair or replace any product or product
part that is defective. If Premier Mounts chooses to replace a defective product or part, a replacement
product or part will be shipped to you at no charge, but you must pay any related labor costs.
What is Not Covered: Limitations
Premier Mounts disclaims any liability for damage to mounts, adapters, displays, projectors, other
or misuse of its products.
NOTWITHSTANDING ANYTHING TO THE CONTRARY IN THIS WARRANTY, THIS WARRANTY
IS LIMITED TO FIVE YEARS FROM THE DATE OF PURCHASE IN THE EVENT THAT THE WAR-
RANTED PRODUCT IS COMMERCIALLY RENTED OUT.
and related electrical items, are backed by a 3-year warranty.
Premier Mounts disclaims all other warranties, express or implied, including warranties of merchant-
-
quential damages, including but not limited to, inability to use its products or labor costs for remov-
ing and replacing defective products or parts. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or exclusion may not apply to you.
What Customers Must Do for Warranty Service
If you discover a problem that you think may be covered by the warranty, you must report it in writ-
ing to the address below within thirty (30) days. Proof of purchase (an original sales receipt) from the
original consumer purchaser must accompany all warranty claims. Warranty claims must also include
a description of the problem, the purchaser’s name, address, and telephone number. General inqui-
ries can be addressed to Premier Mounts Customer Service at 1-800-368-9700. Warranty claims will
not be accepted over the phone or by fax.
How State Law Applies
state to state.
PREMIER MOUNTS
500 W Central Ave, Suite A
Brea, CA 92821
USA & CANADA
Phone: [phone]
Fax: [phone]
©
e. [email protected]
PREMIER MOUNTS
ATTN: Warrenty Claims
500 W Central Ave, Suite A
Brea, CA 92821