Premier Mounts PSD-TTS/B User manual

9532-002-001-11 PSD-TTS-B Installation Guide
INSTALLATION MANUAL
TABLETOP STAND
PSD-TTS-B
1321 S State College Blvd. Fullerton, CA 92831 Phone: [phone] Fax: [phone]

9532-002-001-11 PSD-TTS-B Installation Guide
2
www.mounts.com
oSafety & precautions
oStand diagrams
oParts list (1)
oFlat panel list
oParts list (2)
oChecking the thread depth on your flat panel
oBuilding the stand
oSecuring the mounting brackets
oSecuring the flat panel to the stand
o(Optional) fixed installation
The entire installation instructions should be fully read and understood, including all of the safety symbols and safety precautions before
beginning installation. The installation instructions should be read, understood and followed to prevent personal injury or property damage.
Keep these installation instructions in an easily accessible location for future reference.
Do not install near heater, fireplace, direct sunlight or air conditioning or any other source of direct heat energy. Failure to do so may
result in damage to the flat panel display and could cause a risk of fire.
At least two qualified people should always perform the installation work. Injury and damage can result from dropping or mishandling
the flat panel display.
Contents
Safety & Precautions
WARNING: Safety precaution measures must be practiced at all times during the installation of this product. Use proper safety gear and tools for the
installations procedure to prevent personal injury or damage to the flat panel display mount.
The tabletop should be capable of supporting a max weight of 160 Lbs., the weight of the flat panel. More than 160 Lbs the tabletop must
be reinforced. Proper installation procedure by qualified personnel as outlined in the installations instructions must be adhered to. Failure to
do so could result in serious personal injury.

9532-002-001-11 PSD-TTS-B Installation Guide
3
32.000
(812)
30.590
(776.9)
30.00
(762)
27.746
(704.7)
1.500
(38.1)
Ø1.500
(38.1)
8.271
(210.0)
1.000
(25.4)
PART#:
PSD-TTS-B
COLOR:
Silver
A. Back cover
B. Vertical brackets
C. Mounting brackets
D. Griplates™ & mounting hardware
E. Aluminum block
F. Base
Stand diagrams
Dimensions are in Inches and (mm)
A
B
D
C
E
F
Base dimensions:
1.00”(25.4) Hx 30.00”(762) W x 13.0”(330) D

9532-002-001-11 PSD-TTS-B Installation Guide
4
Parts list (1)
All of these parts are used to install the mounting bracket. Make sure that none of these parts are missing before beginning installation. If there
are parts missing stop the installation and contact Premier Mounts.
Griplates™ (8)
Thread depth
indicator (1)
Parts list (2)
Aluminum block (1)
Mounting brackets (2)
Base (1)
Tubes (2)
Allen key (1)
M5 x 10 Phillips
screws (2)
M5 x 30 Phillips flat
head screws (5)
Socket head
Screws (6)
Tube caps (2)
Wood screws (2)
(Optional use)
Rubber vinyl (4)
(used on the PSD-TTS/C only)
Rubber feet (4)
(used on the PSD-TTS only)
M6 Phillips
screws (4)
Back cover (1)

9532-002-001-11 PSD-TTS-B Installation Guide
5
NOTE: This wall mount is shipped with all proper installation hardware and components. Make sure that none of these parts are missing before
beginning installation. If there are parts missing stop the installation and contact Premier Mounts.

9532-002-001-11 PSD-TTS-B Installation Guide
6
Checking the thread depth on your flat panel
Inverted flat panel
display
Thread insert
Thread depth
indicator
Figure 2
Figure 3
Figure 1
Marking the depth
1. Insert the thread depth
indicator (supplied) through
the thread inserts found on
the back of the flat panel to
make sure the inserts
measure the same full depth
and mark it.
(see figure 1)
2. Locate the correct diameter
screw for the thread insert.
Compare your marking to the
screws (supplied). If your
selected screw is longer than
the marking on the thread
depth indicator DO NOT USE
this screw.
The screw length must not
bypass the marking. Select
another screw size
(see figure 2 and 3). Until you
find one that comes closest to
your mark without going past.
Marking
Screw
Marking

9532-002-001-11 PSD-TTS-B Installation Guide
7
Building the stand
Step 1
Unpack the components from the box and set them on the floor. Invert and secure the rubber vinyl or rubber feet depending on model to
the bottom of the base. Secure the aluminum block to the base as shown in (figure 1) to the base by using the five (5) M5 x 30 (mm) Phillip
flat head screws (supplied).
CAUTION: Do not over tighten the screws. Find a suitable location for the stand.
Aluminum
block
Base
(5) M5 x 30 (mm)
Phillips flat head
screws

9532-002-001-11 PSD-TTS-B Installation Guide
8
Step 2
Insert the tubes into the secured aluminum block. See diagram to set the cable access openings before tightening the set screws.
See figure A. Once the poles are fully inserted into the block and set to their proper positions lock the tubes by tightening the two
(2) M8 socket head screws. Do not over tighten the set screws. Install the plastic caps to the top of the tubes. See figure 2.
Plastic caps
Allen wrench
(2) M8 x 10 socket
head screws
Base
Tubes
2 O’clock
10 O’clock
Tube location for cable
access

9532-002-001-11 PSD-TTS-B Installation Guide
9
Ω
Step 3
Invert the flat panel display and lay it on a soft and flat surface. Apply the vertical brackets and center the mounting brackets from left to
right on the display. Secure the mounting brackets with the hardware and griplates™ (supplied). NOTE: The griplates™ come with an
M4,M5,M6 and M8 access holes. Find out what your proper hardware for your flat panel will be and use accordingly.
Do not over tighten the hardware.
See figure 3.
(2) Mounting
brackets
Mounting hardware
(see charts) on
page 5,6
(8) Griplates™
(supplied)
NOTE: All Griplates™
tips must be facing up
prior to installation.
(4) M8x10 Socket
head screws
Allen key
Soft and flat
surface

9532-002-001-11 PSD-TTS-B Installation Guide
10
Securing the flat panel to the stand
Step 4
Raise the display (see warning on this page) and slide the mounting brackets over the tubes, set the height required and using the Allen
wrench secure the height by tightening the four (4) M8 socket head screws. Do not over tighten the screws. Make all proper connections
at this time. Install the back cover plate and secure it using two (2) M5 x 10 phillips screws (supplied). See figure 4.
Allen wrench
Back cover
(2) M5 x 10
phillips screws
WARNING: AT LEAST (2) QUALIFIED
PERSONNEL ARE STRONGLY
RECOMMENDED FOR INSTALLATION OF
THIS PRODUCT. FAILURE TO DO SO
COULD RESULT IN SERIOUS INJURY AND
POSSIBLE DAMAGE TO THE FLAT PANEL.
Cable routing access
points

9532-002-001-11 PSD-TTS-B Installation Guide
11
(Optional) fixed installation
Step 5
If securing to a wood table, secure the stand with the two (2) #10 x 1-3/4" wood screws (supplied).
NOTE: Longer or shorter wood screws and or mounting hardware depending on your installation environment are
(commercially available). See figure 5.
Wood screw
access holes
#10 x 1-1/4”
wood screws
Flat wood surface
Base