Premio CT-DWL01 User manual

USER’S
MANUAL
CT-DWL01
3.5" SBC Industrial Motherboard with 8th Gen. Intel®
Core™Processor i3/i5/i7 &
Intel® Celeron® Processor

CT-DWL01 l User’s Manual
Table of Contents
Prefaces …………………………………………………….…………………………………………….04
Revision …………………………………………………………………………………………..……………….………..04
Disclaimer ………………………………………………………..…….…….………………………….……………….. 04
Copyright Notice …………………………………….…………………….…………………………………………… 04
Trademarks Acknowledgment …………..……………………………………………………….................. 04
Environmental Protection Announcement …………………………….………………….…………..….. 04
Safety Precautions ………………………………………….……………………………….…………….……….... 05
Technical Support and Assistance …………………………………….…………….…………….………….. 06
Conventions Used in this Manual ………………………………………………………………….….………. 06
Chapter 1 Product Introductions ………………………………………………………..…07
1.1 Product Description ……….………………………………..………….………………..………. 08
1.2 Specifications ………………..………………………….....…………….…………..…..………… 09
1.3 Available Models …………………..……………………..…………………………………..…... 10
Chapter 2 Mechanical Specifications ….…………………..………………………..…. 11
2.1 Switch and Connector Locations ..…………………………………..…….…..……..….... 12
2.2 Connector / Switch Definition …..………………………….……….…….………............ 14
2.3 I/O Interface Descriptions .………..…............................................................. 15
2.3.1 Clear CMOS……....…………….…………………………………………....……………… 15
2.3.2 Panel PWR setting …….…….…………………………………………....……………… 15
2.3.3 Backlight PWR setting ...……….……………………………………....……………… 16
2.3.4 Front Panel Header……………………………………....………………………………. 17
2.3.5 AT/ATX setting ……..…..……………………………………………....………………..… 18
2.3.6 Panel control ………..…………..……………………………………....…………………. 19
2.3.7 USB3 …………………………………………………………….……………....……………… 20
2.3.8 USB …………………………………………………………….……………………………..…. 21
2.3.9 eDP ………………………………………..………………………..……………………..….… 22
2.3.10 COM Port COM1 ………...………………..……………………………………………. 23
2.3.11 COM Port COM2 ……………………………………………………………………….. 24
2.3.12 COM Port COM3 …….……………………………………....……………………..…… 25
2.3.13 COM Port COM4 ………….…………………....………………………………….…… 26
2.3.14 GPIO ………………………………....……………………………………………………..… 27
2.3.15 SATA1 ………………………………....………………………………………………………. 28
2.3.16 SATA2 …………………………………………....………………………………………….… 29
2.3.17 SATA1_PWR1 …………………………………...………………………………………… 30
2.3.18 SATA2_PWR1 ………………………………………….………………………..……….. 31
2.3.19 USB2.0 ………………………………………………………………………………………… 32
2.3.20 DC12_IN …………………………………………...………………………...……….…… 33
2.3.21 FAN PWR ……………………….…………….…………………………………………….. 34
2.3.22 HDMI ………………………………………………………..……………...………………… 35
2.3.23 DP ……………………………………………………………………………..……………….. 36
2.3.24 RJ45 ……………………………………………………………………………….……..…… 37
2.3.25 LVDS ……………………………………………………………….………...………….…… 38
2

CT-DWL01 l User’s Manual
3
Chapter 3 Features & Interfaces ………………………………………………………..…39
3.1 Processor ……………………….………………………………..………….………………..………. 40
3.2 BIOS ……………………………..………………………….....…………….…………..…..………… 40
3.3 System Memory ……….…………..……………………..…………………………………..…... 40
3.4 Graphics ………………………………………..…………………………..………..……….………. 40
3.5 USB ……………………………….………………………………..………….………………..………. 40
3.6 Ethernet ……..………………..………………………….....…………….…………..…..………… 40
3.7 SATA ………………..……….…………..……………………..…………………………………..…... 40
3.8 Audio ………………………………..…………..…………………………..………..……….………. 40
3.9 Expansion ……………………..………………………….....…………….…………..…..………… 41
3.10 General Purpose Input Output ……………………..…………………………………..…... 41
3.10.1 GPIO Configuration ……………………..……….………………………………..…... 41
3.11 Watchdog Timer ………………..…………..…………………………..………..……….………. 42
3.11.1 Board Design ……………..………………..……….………………..……………..…... 42
3.11.2 Psuedo Code ……………..………………..……….……………………..………..…... 42
Chapter 4 Driver Installation ….…………………..………………..……………..…..…. 43
Chapter 5 System BIOS ….…………………………..………………..……………..…..…. 45
5.1 BIOS Introduction ………….….…………………………………..……...…….…..……..….... 46
5.2 Main Setup ………….….…………………………………..……...…….……………..……..….... 47
5.3 Advanced Setup ………….….…………………………………..……...…………..……..….... 48
5.3.1 CPU Configuration …………….…………………………………………....…………… 49
5.3.2 PCH-FW Configuration ………..…….………………..…………..…………………… 50
5.3.3 SATA and RST Configuration ...……………………………………....……………… 51
5.3.4 RST (UEFI RAID) Configuration ……..……….……………....………………..…… 52
5.3.5 Trusted Computing ……..……………………………………………....…………..…… 54
5.3.6 ACPI Settings ………..…………..……………………………………....……………….… 55
5.3.7 Super IO Configuration …………….………………………....……………….……… 56
5.3.8 Hardware Monitor ………..…….………………..………………………………….….. 61
5.3.9 Serial Port Console Redirection …..……….…………………....………………… 63
5.3.10 Network Stack Configuration .………………………….………....……………… 64
5.3.11 CSM Configuration .……..………………………..…………………....……………… 65
5.3.12 USB Configuration …………..…………………..……………….…....……………… 66
5.4 Chipset ………….………………………………........................................................... 67
5.4.1 System Agent (SA) Configuration ...……………………………....……………… 67
5.4.2 PCH-IO Configuration …………..……………………………....………………......… 70
5.5 Security …….……………………..……………........................................................... 75
5.6 Boot ……………..………………………………........................................................... 78
5.7 Save and Exit …………………………………........................................................... 79
Appendix WDT & GPIO .…………………………..………………..……………..…..…. 80

CT-DWL01 l User’s Manual
4
Revision
Disclaimer
All specifications and information in this User’s Manual are believed to be accurate and up to date. Premio
Inc. does not guarantee that the contents herein are complete, true, accurate or non-misleading. The
information in this document is subject to change without notice and does not represent a commitment
on the part of Premio Inc.
Premio Inc. disclaims all warranties, express or implied, including, without limitation, those of
merchantability, fitness for a particular purpose with respect to contents of this User’s Manual. Users
must take full responsibility for the application of the product.
Copyright Notice
All rights reserved. No part of this manual may be reproduced or transmitted in any form or by any means,
electronic or mechanical, including photocopying, recording, or information storage and retrieval systems,
without the prior written permission of C&T Solution Inc. Copyright © C&T Solution Inc.
Trademarks Acknowledgment
Intel®, Celeron® and Pentium® are trademarks of Intel Corporation.
Windows® is registered trademark of Microsoft Corporation.
AMI is trademark of American Megatrend Inc.
IBM, XT, AT, PS/2 and Personal System/2 are trademarks of International Business Machines Corporation
All other products and trademarks mentioned in this manual are trademarks of their respective owners.
EnvironmentalProtection Announcement
Do not dispose this electronic device into the trash while discarding. Please recycle to minimize pollution
and ensure environment protection.
Prefaces
Revision Description Date
1.0 Initial release 2020/10/12
Preface

CT-DWL01 l User’s Manual
5
Safety Precautions
Before installing and using the equipment, please read the following precautions:
⚫Put this equipment on a reliable surface during installation. Dropping it or letting it fall could
cause damage.
⚫The power outlet shall be installed near the equipment and shall be easily accessible.
⚫Turn off the systempower and disconnect the power cord from its source before making any
installation. Be sure both the systemand the external devices are turned OFF. Sudden surge
⚫of power could ruin sensitive components. Make sure the equipment is properly grounded.
⚫When the power is connected, never open the equipment. The equipment should be opened
only by qualified service personnel.
⚫Make sure the voltage of the power source is correct before connecting the equipment to the
power outlet.
⚫Disconnect this equipment from the power before cleaning. Use a damp cloth. Do not use
liquid or spray detergents for cleaning.
⚫Avoid the dusty, humidity and temperature extremes.
⚫Do not place heavy objects on the equipment.
⚫If the equipment is not used for long time, disconnect it from the power to avoid being
damaged by transient over-voltage.
⚫The storage temperature shall be above -40°C and below 85°C.
⚫The computer is provided with a battery-powered real-time clock circuit. There is a danger of
explosion if incorrectly replaced. Replace only with the same or equivalent type
recommended by the manufacturer.
⚫If one of the following situation arises, get the equipment checked be service personnel:
•The power cord or plug is damaged.
•Liquid has penetrated into the equipment.
•The equipment has been exposed to moisture.
•The equipment does not work well or it cannot work according the user’s manual.
•The equipment has been dropped and damaged.
•The equipment has obvious signs of breakage.
Preface

CT-DWL01 l User’s Manual
6
Technical Support and Assistance
Contact your distributor, our technical support team or sales representative for technical support if you
need additional assistance. Please have following information ready before you call:
⚫Model name and serial number
⚫Description of your peripheral attachments
⚫Description of your software (operating system, version, application software, etc.)
⚫A complete description of the problem
⚫The exact wording of any error messages
Conventions Used in this Manual
Preface
This indication alerts operators to an operation that, if not strictly observed,
may result in severe injury.
WARNING
This indication alerts operators to an operation that, if not strictly observed,
may result in safety hazards to personnel or damage to equipment.
CAUTION
This indication provides additional information to complete a task easily.
NOTE

Chapter 1
Product Introductions

CT-DWL01 l User’s Manual
8
1.1 Product Description
The CT-DWL01 is a single board computer in 3.5" SBC Industrial Motherboard with 8th Gen. Intel®
Core™Processor i3/i5/i7 & Intel® Celeron® Processor
• 1x 260-pin DDR4 2400 SO-DIMM. Max. up to 32GB
• Triple independent display supported by:
1x DisplayPort support resolution 4096 x 1200
1x Dual-channel, up to 24-bit LVDS optional 1x eDP via internal connector
1x HDMI support resolution 1920 x 1200 (Optional)
• 1x Front Panel with Audio support by internal header
• 2x 4bit GPIO header
• 2x Mini PCI-e (Gen3) w/ SIM slot support
• 4x USB 3.2 Gen 2 (10Gbps), 4x RS-232/422/485 internal headers,
2x USB 2.0 internal header
• 2x SATA 6.0Gb/s
• Watchdog timer 1~225sec. system reset
• TPM 2.0 Supported
Chapter 1: Product Introductions

CT-DWL01 l User’s Manual
9
Chapter 1: Product Introductions
1.2 Specifications
System
Processor
Support 8th Gen. Intel® WL-UE Processor (15W TDP)
•Intel® Core™i7-8665UE Processor 8M Cache, up to
4.40 GHz
•Intel® Core™i5-8365UE Processor 6M Cache, up to
4.10 GHz
•Intel® Core™i3-8145UE Processor 4M Cache, up to
3.90 GHz
•Intel® Celeron® Processor 4305UE2M Cache, 2.00
GHz
System Memory : SoC
LAN Chipset :
•GbE1: Intel® I219LM (Support Wake-on-LAN and
PXE)
•GbE2: Intel® I210-IT (Support Wake-on-LAN and PXE)
Audio Codec : Realtek ALC888S HD Audio Codec
Memory : 1x 260-Pin DDR4 2400MHz SO-DIMM slot
Max. Size : 32GB
BIOS : AMI uEFI 256MB SPI flash
Watchdog : Software Programmable Supports 1~255
sec. System Reset
TPM : TPM 2.0 Through Infineon® SLB9665TT2.0 or
Equivalent
Display
Chipset :
•Intel® UHD Graphics 620 for Core series
•Intel® UHD Graphics 610 for Celeron series
Interface :
•1x DisplayPort support resolution 4096 x 1200
•1x LVDS & 1x EDP internal connector
•1x HDMI support resolution 1920 x 1200
(Optional)
Multiple Display : TripleDisplay (HDMI Optional)
Expansion
Mini PCI Express : 2x Mini PCI-e x1 (Gen3)
Rear I/O
LED : 1x Power LED, 1x HDD LED indicator
LAN : 2x RJ45
Display :
•1x HDMI 1.4, 4096x2160 @30/24Hz
•1x DisplayPort DP 1.2, 4096x2304 @60Hz
USB : 4x USB 3.2 Gen 2 (10 Gbps)
Internal I/O
Display :
•1x LVDS Dual -channel, up to 24-bit (1920x1200)
•1x eDP1.4 (4096x2306 @60Hz) (Optional )
COM : 4x RS-232/422/485 internal 2.0PH headers
USB : 2x USB 2.0 internal via a PH2.0 2x 10pin header
SATA : 2x SATA Gen3, w/2x 4pin SATA Power connector
Audio : 1x Front panel audio
DIO : 2x 4-bit DIO (4-in/4-out) via a PH2.0 2x 10pin
header, (PIN1_VCC, PIN2_GND)
Others :
1x Front panel
1x 4-pin PWM smart fan
1x Debug Port
1x RTC battery by cable
Operating System
Windows : Microsoft® Windows® 10 64-bit(RS5 or
above)
Linux : Linux Kernel 5.x (Fedora 30 or above / Ubuntu
19.04 or above)
Power
Power Connector : 4-pin CPU P4 connector
Power Input : AT/ATX 12V DC Input
Management : ACPI
Mechanical & Environment
Form Factor : 3.5" Embedded SBC
Dimension : 146 x 102mm
Operating Temp :
-40°C ~ 85°C, 95% (non-condensing), operating
Storage Temp :
-40°C ~ 85°C, 95% (non-condensing), Non-operating
Relative Humidity :
10% ~ 90% relativehumidity, non-condensing
ORDERING INFORMATION
Packing List
•1 x Heat Sink
•1 x SATA Power Cable
•1 x Driver DVD
Ordering Information
CT-DWL01-8365UE :
3.5" SBC with Intel® Core™i5-8365UE, DP, HDMI, 2x
LAN, 4x USB
CT-DWL01-4305UE :
3.5" SBC with Intel® Celeron® 4305UE, DP, HDMI, 2x
LAN, 4x USB
CT-DWL01-8665UE : (Optional)
CT-DWL01-8145UE : (Optional)

CT-DWL01 l User’s Manual
10
1.3 Available Models
Chapter 1: Product Introductions
Ordering Information Part Number
CT
-DWL01-8365UE
3.5" SBC with Intel® Core
™i5-8365UE, DP, HDMI, 2x LAN, 4x USB
CT
-DWL01-4305UE
3.5" SBC with Intel® Celeron® 4305UE, DP, HDMI, 2x LAN, 4x USB
CT
-DWL01-8665UE
(Optional)
CT
-DWL01-8145UE
(Optional)

Chapter 2
Mechanical Specifications

CT-DWL01 l User’s Manual
12
2.1 Switch and Connector Locations
Chapter 2: Mechanical Specifications
2.1.1 Top View
USB_2
SATA1_PWR
SATA2_PWR
SATA1
BAT2
COM1
COM2
COM3
COM4
LVDS1
RJ1
DP1
MINI_PCIE2
BZ1
MINI_PCIE1
SODIMM1
CN4
CN3
HDMI
FAN1 JP1
CN2JP4GPIO1JP5JP6DC_IN2 JP3
SATA2

CT-DWL01 l User’s Manual
13
Chapter 2: Mechanical Specifications
2.1.2 Bottom View
CN31

CT-DWL01 l User’s Manual
14
2.2 Connector / Switch Definition
Chapter 2: Mechanical Specifications
Connector Location Definition
JP1 Clear CMOS header
JP3 Panel PWR setting header
JP4 Backlight PWR setting header
JP5 Front Panel header
JP6 AT/ATX setting header
CN2 Panel Control
CN3 USB3.1 port
CN4 USB3.1 port
COM1 COM1 Serial Port header
COM2 COM2 Serial Port header
COM3 COM3 Serial Port header
COM4 COM4 Serial Port header
GPIO 4IN/4OUT GPIO header
SATA1 SATA Port 1 signal connector
SATA2 SATA Port 2 signal connector
SATA1_PWR SATA Port 1 power connector
SATA2_PWR SATA Port 2 power connector
LVDS1 LVDS connector
USB_2 USB 2.0 headers
MINI_PCIE1 Mini PCI Express slot 1 with SIM
MINI_PCIE2 Mini PCI Express slot 2 with mSATA
DC_IN2 4 PIN Power connector
FAN1 FAN Power connector
RJ45 LAN1/2 ports
HDMI HDMI signal connector
DP1 DP signal connector
BAT2 Battery connector

CT-DWL01 l User’s Manual
15
2.3 I/O Interface Descriptions
Chapter 2: Mechanical Specifications
2.3.1 Clear CMOS
JP1
Pin Signal
1NC
2 RTCRST#
3 GND
1
2
3
JP3
2.3.2 Panel PWR setting
Pin Signal
1 +V3.3A
2 P3P5V
3 +V5A
1
2
3

CT-DWL01 l User’s Manual
16
2.3 I/O Interface Descriptions
Chapter 2: Mechanical Specifications
2.3.3 Backlight PWR setting
JP4
Pin Signal
1 +V12A
2 P5P12V
3 +V5A
1
2
3

CT-DWL01 l User’s Manual
17
2.3 I/O Interface Descriptions
Chapter 2: Mechanical Specifications
2.3.4 Front Panel Header
JP5
Pin Signal Pin Signal
1 Power(3.3V) 2 SATA_LED#
3 Power(3.3V) 4 GND
5 LOUT_R 6 RESET_BUTTON_N
7 LOUT_L 8 PS_ON_BUTTON_N
9 MICIN1_R 10 GND
11 MICIN1_L 12 AGND_HD
1 2
11 12

CT-DWL01 l User’s Manual
18
2.3 I/O Interface Descriptions
Chapter 2: Mechanical Specifications
2.3.5 AT/ATX setting
JP6
1
2
3
Pin Signal
1NC
2 AT MODE
3 PS_ON_BUTTON_N

CT-DWL01 l User’s Manual
19
2.3 I/O Interface Descriptions
Chapter 2: Mechanical Specifications
2.3.6 Panel control
CN2
Pin Signal Pin Signal
1 LVDS_BKLTEN 2 LBKLT_CTRL
3 BLPWR 4 BLPWR
5 GND 6 GND
7 CH7511_BLUP 8 CH7511_BLDN
1
2
3
4
5
6
7
8

CT-DWL01 l User’s Manual
20
2.3 I/O Interface Descriptions
Chapter 2: Mechanical Specifications
2.3.7 USB3
CN3
Pin Signal Pin Signal
1 USBVCC0 10 USBVCC0
2 USB2-2N_CONN 11 USB2-1N_CONN
3 USB2-2P_CONN 12 USB2-1P_CONN
4 GND 13 GND
5 USB3-RN2_CONN 14 USB3-RN1_CONN
6 USB3-RP2_CONN 15 USB3-RP1_CONN
7 GND 16 GND
8 USB3-TN2_CONN 17 USB3-TN1_CONN
9 USB3-TP2_CONN 18 USB3-TP1_CONN