Premio eDrawer4060J-S3 User manual

Installation and service of this product should be conducted by a trained
personnel to avoid any bodily injury from electric shock or heavy object
Observe ESD (Electrostatic Discharge) practices during integration to avoid
possible damage to the board and / or other components
eDrawer4060J-S3 Quick Guide
Version 1.10 –2017.02.21
1. Check the content of the box. Please confirm that
your package contains the following:
#
Description
Image / Description
Qty
1
eDrawer4060J-S3
Enclosure
1
2
Screw Set for
Mounting Drives*
1 set
3
Expander Module
1 or 2
4
Power Cable*
2
5
Serial Cable*
1
6
Rail, Bracket, and
screws*
2 sets
7
Chassis Handle*
2
8
Support Bar
2
9
SFF 8644-8644 / SFF
8088-8644 SAS cable
optional
2
10
This Quick Guide
1
11
Packaging
1 set
* Inside the accessories box. If any items are missing, please contact
your authorized reseller or sales representative
2. Get familiar with the unit.
Front view of the unit
Rear view of the unit
Expander Module
3. Remove the Unit from the packaging. Use chassis
handles to help lifting the unit from the box.
4. Pull the Drive Module out of the unit as indicated
in order to install disk drives. It is recommended to install
HDDs after the unit is mounted to the cabinet.
Drive module cannot be completely removed. Drives can be
inserted and removed from the module while system is
running without disrupting the operation.
5. Install HDDs as illustrated below. SAS and SATA drives
may be sold separately. SAS drives are required for
eDrawer4060J-S3 configuration with dual expander.
6. Prepare the Rack Posts with square nuts (red
squares). Red circles are location for support bar screws.
Proceed to install the rear brackets and apply M5x10L screws.
Do NOT tighten yet. Allow wiggle room for rail installation.
7. Install the Support Bar to the rack.
Thank you for your purchase of Premio eDrawer4060J-S3 Storage System!

eDrawer4060J-S3 Enclosure Quick Guide
For more information please visit our website at www.Premioinc.com
Copyright © 2017,Premio Inc. All rights reserved.
8. Prepare the unit for rack installation.
9. Place the Unit to the Rack carefully as follows:
10.Drive Mapping of the system is as follows
11. Establish SAS connection to host, client, or
switch. By default, a minimum of 2 SAS cables are required to
access all 60 HDDs (30 HDDs for each connected SAS ports).
Refer to the system configurations below to decide on which
port to use.
Single expander mode: SAS drives are not required, no high
availability is possible with this configuration. The SAS
HBA/RAID controller sees all 60 HDDs from eDrawer4060J-S3.
Connect SAS cable to Host Port of the Primary Module.
Daisy-chain mode: a single expander mode with expandable
storage. The SAS HBA/RAID controller sees the collective
HDDs from the daisy-chained eDrawer4060J-S3’s.
Dual expander mode: SAS drives are required. Two clients are
able to connect to the unit storage device due to the dual
port nature of the SAS drives. This configuration provides a
redundant path and high availability.
Clustered Storage Spaces mode: SAS drives are required. In
the above configuration, both hosts will have all the paths to
all 60x disks at the same time.
12. Plug in the Power Cords to four AC receptacles
on the back of the unit.
13. Press the Power Switch on the
back of the unit and wait until the unit is ready
(all HDDs spin up) before powering up the
client.
14. Access the Serial
Console (when necessary) by
connecting a serial audio cable to
the debug console port and use a
terminal console with baud rate
38400, 8, N, 1, N.
Type “help –a” for the list of commands.