Prescitech E300 Specification sheet

E300 Mini WiFi Range Extender / AP / Router
GET STARTED

Overview
Package Contents....................................................
Front Panel ..............................................................
LED Descriptions......................................................
Using as an Extender
Connects to a WIFI network...................................
Acts as an access point for WIFI devices.............
Power on the E300................................................
Connect to an existing WIFI network.....................
Method 1: Connect with a web browser............
Method 2: Connect with WPS...........................
Connect an Ethernet-enabled Device...................
Using as an Access Point.......................................
Other Settings
Change the password of Prescitech E300............
Hide extender’s wireless network..........................
Troubleshoots
01
02
03
01
04
14
16
04
04
05
06
06
08
09
10
14
15

01
The Prescitech E300 WiFi Range Extender is a network
device with multifunction, which can be using for
increasing the distance of a WiFi network by boosting
the existing WiFi signal and enhancing the overall signal
quality over long distances. An extender repeats the
signals from an existing WiFi router or access point.
The Prescitech E300 WiFi Range Extender also can be
used as an Access Point.
Package Contents
E300 WiFi Extender/AP/Router x 1
Quick Installation Guide x 1
RJ-45 Networking Cable x 1
User Manual x 1
Reset Pin x 1
Overview

02
Before you install your extender, familiarize yourself with
its LEDs, buttons, and port.
Front Panel
2 x External Antennas
WLAN LED 3
WPS Button
LAN WAN/LAN
WLAN LED 2
WLAN LED 1
Power/ WPS LED
WAN/ LAN LED
LAN LED
Power Switch
Mode
Selector Switch
Reset
RESET

03
Blinking Fast. The port is sending or receiving traffic.
Off. No Ethernet cable connected.
Power/WPS LED
WAN/LAN LED
Blinking Fast. The port is sending or receiving traffic.
Off. No Ethernet cable connected.
LAN LED
Lit. Power on.
Blinking. A WPS connection is being established.
OFF. Power is not supplied.
LED Descriptions
WLAN LED 1 – LED 3
Wi-Fi fadio is operating
Best connection
Good connection
Poor connection
Mode
LEDs Description
Aeccess Point
Router
Repeater
ON
Bliking OFF OFF
ON OFF OFF
ON OFF
ON
ON
ON ON
ON ON
Wi-Fi fadio is operating
Disconnection
ON ON ON
12 3

04
The extender works like a bridge between a WIFI router
(or an access point) and a WIFI device out of the range
from WIFI router. The extender performs two main jobs:
When the extender connects over WIFI to an existing
network, it functions as a network client, similar to one
WIFI device connects to a network.
The extender broadcasts its own signal that WIFI
devices can join. As an access point, the extender
performs tasks that router does, such as broadcasting its
network name (SSID).
The extender must do each of these jobs so that both
ends of the bridge are in place.
Using as an Extender
Boosts the range of your
existing WiFi and creates
a stronger signal in hard
to reach areas.
WiFi Range Extender
sometimes your router
does not provide the
WiFi coverage you need.
Existing WiFi
Connects to a WIFI network
Acts as an access point for WIFI devices

05
Switch the power button “ON” & the mode button to
“Repeater” on the side of the E300. Plug the E300
into an electrical outlet which next to your WIFI
router. The E300 plugged in the proximity of the
WIFI router only for the initial setup process.
Power on the E300
1
WPS
WLAN
Power/WPS
WAN/LAN
LAN
ON OFF
Repeater
Access Point
Router
Power/WPS
WLAN
WAN/LAN
LAN
Access Point Router
Repeater
ON OFF
Blinking

06
To extend the range of your WiFi network, you must
connect the extender to your existing WiFi network.
You can do this in one of two ways:
Method 1. Connect with a web browser.
Method 2. Connect with WPS. (more details on
page 08)
Connect to an existing WIFI network
1. Once connected, visit: http://extenderlogin.com or
192.168.10.1 . When prompted, enter “admin” in
a lower-case to login. (admin page not available?
visit the troubleshoots on Page 16)
Method 1: Connect with a web browser
2
Prescitech
Wi-Fi Range Extender
admin
English
Login

07
3. It is around half a minute to reboot the E300. You can
connect back the new SSID of E300 by locating the
suitable place you need (how to locate the repeater
please refer to the troubleshoots on Page 16).
NOTE: Once setup successful, the WLAN LEDs would
change into Lit Green. The WLAN LED1 keeps blinking
if the setup failed, you might enter the wrong password
on step 3.
Repeater Wizard
Connect to: ASUS
E300 SSID: ASUS_EXT
Select a Wi-Fi
ASUS
XXXXXX
XXXXXX
Home Wizard Wi-Fi Settings
Manually enter
Wi-Fi Password:
Connect
2. Click “Wizard”& choose the your router SSID, fill in
the Wi-Fi Password of your router, then click
“Connect”. If the wireless Network list could not load
completely or successful, please click to refresh.

08
Wi-Fi Protected Setup (WPS) lets you join a secure WiFi
network without typing the network name and password.
Note: WPS does not support WEP network security.
1. Press the WPS button on the front panel of the E300
around 6 seconds. Release the button, then the WPS
LED blinks.
2. Within two minutes, press the WPS button on your
router or access point.
3. When the E300 connects to your existing WIFI
network successful, the E300 WIFI network name
would be changed into “Your Router SSID_EXT”, and
the WLAN LEDs are all lit green. If the E300 fails to
connect, the WLAN LED1 would keep blinking, try it
once again. If still failed, use the Method 1 on page 06.
4. It is around half a minute to reboot the E300. You can
connect back the new SSID of E300 by locating the
suitable place you need (how to locate the repeater
please refer to the troubleshoots on Page 16).
Method 2: Connect with WPS