Prestige APSRS User manual

APSRS
Remote Start w/Keyless Entry
System Layout
For Complete Installaon Guide and Technical Support Visit www.voxxuniversity.com. Or Call 1-800-225-6074 2019 Voxx Electronics. All Rights Reserved.
1
2
3
4
1 2 3 4
1
2
3
4
1Red/Black Ignition 3 Flex Relay (87)Input
2 PinkIgnition 3 Flex Relay (30)Output
3 YellowStarter Output (+)
4 GreenIgnition 2 Output (+)
5 Red Battery 12VInput (+)
6 Red/White Battery 12VInput (+)
7 PurpleAccessory Output (+)
8 BlueIgnition 1 Input / Output (+)
8 Pin Start
P
P
P
1White Data RX
2Black Ground (-)
3 Blue Data TX
4 Red Battery 12V (+)
DBI
1Green Data RX
2Blue Data TX
3 Black Ground (-)
4 Red Battery 12V (+)
RF
1Blue Data TX
2White Data RX
3 Black Ground (-)
4 Red Battery 12V (+)
CarLink
4 Red Battery 12V (+)
3 Black Ground (-)
2White Data RX
1Blue Data TX
Weblink
22
GreenUnlock Output (-) (NOC 11)
21
Dk. BlueTrunkOutput (-) (NOC 9)
20 Red Lock Output (-) (NOC 10)
19 Green/Lt. Blue Ch. 4 AUX Output (-) (NOC 8)
18 Black/White Horn Output (-)
17 Lt. Blue/Green Ch. 5 AUX Output (-) (NOC 7)
16 Red/Black 2nd Unlock Output (-) (NOC 12)
15
Black/Lt. GreenFactory Arm Output (-) NOC 6)
14 Brown/Black Brake Input (+)
13 Black/Blue Factory Disarm Output (-) (NOC 5)
12 Dk. Blue/Black External Activation Input (-)
11 Black/Red Pulse After Shutdown Output (-) (NOC 4)
10 Orange/Black Parking Brake Input (-)
9 Black/Yellow Pulse During CrankOutput (-) (NOC 3)
8 Green/Yellow Diesel Glow Plug Input (+)
7 Green/White DomeLight Output (-) (NOC 2)
6 Purple/Brown DoorTriggerInput (- / +)
5 Lt. Blue Remote Start Status Output (-) (NOC 1)
4 Green/Orange Tach Input (-)
3 Gray/Black Hood Input (-)
2 Lt. Green TrunkTriggerInput (-)
1 Orange Starter Kill Relay/ Anti-Grind Output (-)
22 Pin Input/Output
1 2 3 4
VOXX
FLCART Dock
Replacement Part #4120457
Replacement Part #4120463
Replacement Part #4120458
Not Included
Not Included
Not Included
Not Included
1 White Parking Light (30)Output
2 White/RedParking Light (87)Input
3 Yellow/Black Ignition Output to Alarm (+)
4 Black Ground Input (-)
4 Pin Light
Replacement Part #4360832
This Harness is included with the FLCART.
For Wire Informa�on and Diagram Please Refer to Vehicle Specific
FlashLogic Install Guide.
Visit www.FlashLogic.com for More Informa�on.
Not Included
19
17
15
13
11
9
7
5
3
1 2
4
6
8
10
12
14
16
18
20
21 22
19 20
17 18
15 16
13 14
11 12
910
7 8
5 6
3 4
1 2
1 3 5 7
2 4 6 8
1 3
2 4
Compable RF Kits
PE1BZ
PE1BZLR
PE1BTWZ
PE5BZ
PE2LEDZ
PE2LCDZ
PE1M2LEDZ
PE1M2LCDZ
Important Update
The default Data Port Protocol of this system is ADS. If using an FLCAN or
other external integraon module be sure to choose iDatalink 2-Way when
ashing.
This system will also support DBI. This will require programming Feature
Bank 2, Feature 15 to DBI.

APSRS
Keyless / Remote Start
Quick Installaon Guide
For Complete Installaon Guide and Technical Support
Visit
www.voxxuniversity.com
Or Call
1-800-225-6074
Nocaons
Feature Programming
Remote Programming
1 Chirp 2 Chirp 3 Chirp 4 Chirp 5 Chirp 6 Chirp
1 Lock / Unlock Funcon 500ms 3.5sec
500ms L, DBL UL DBL L, 500ms UL DBL L, DBL UL 500ms L, 350ms UL
2 Ignion Lock OFF ON
3 Ignion Unlock OFF Unlock All
Unlock Driver
4 Exterior Illuminaon OFF With Arm With Disarm With Arm & Disarm
5 Auto Relock OFF ON
6 Auto Arming / Locking NA
7 Nocaon Sound NA
8 Horn Timing 16ms 30ms 40ms 50ms 10ms
9 Valet Override Method NA
10 Driver Priority Unlock OFF ON
11 Silent Choice OFF From Transmier
OEM Style
12 Security Prole OFF OEM Security ALL ON w/ OEM RS
13 Door Trigger Input Negave Posive
14 Park Light / Trunk Swap OFF ON
15 Data Port Protocol ADS DBI
1 Chirp 2 Chirp
3 Chirp 4 chirp 5 Chirp 6 Chirp
1 Defrost Output Pulsed 10min
RS Runme
2 RS Start Nocaon ON O
3 RS Runme 5min 10min 15min 20min 45min 60min
4 RS Parking Lights Steady Flashing
5 Engine Conrmaon Tach Voltage Data Hybrid
6 Voltage Level >0.5v B4 Start <0.5v B4 Start
7 Ignion 2 Output Ignion Accessory Start
8 Ignion 3 Output Ignion Accessory
Start
9 Accessory Output Accessory Ignion Start
10
Transmission Auto Manual
11 Max Crank Time 0.8sec 1.0sec 1.5sec 2.0sec 3.0sec 4.0sec
12 Diesel Delay OFF Diesel 10
Diesel 15 Diesel 20 Diesel 30
13 Temperature Start OFF ON
14 Crank Duraon Averaging Preset
15 RS Shock Override NA
16 Turbo Timer OFF 3min
5min 10min
17 Start Acvaon Two Press One Press Three Press
18 RS Lock Funcon No Change UL Before L Aer
UL Before Start Lock Aer Start
19 Factory Disarm Output Single Pulse Double Pulse 350ms 500ms 800ms Same As Bank 2, F1
20 Addional Unlock Pulse No Pulse IGN, ACC, GWR
IGN,ACC,GWR,PASD
Features
Feature Bank 2
Opons
Features
Feature Bank 3
Opons
1Runtime Expired
2 Remote Shutdown
3 Brake On
4 Manual Mode
5 Hood Open
6Low / No Tach
7 Tach Programming
8High Tach
Negave Output Control (NOC)
AUX Output Control
OEM Security
Negave output control allows any NOC to be programmed for any one of nineteen (19)
opons. This feature is accessible via FlashLogic Weblink or Weblink Mobile.
Any AUX output can congured using the AUX Control Menu. This feature is only
accessible via FlashLogic Weblink or Weblink Mobile.
Chirp Delete
System ARM/DISARM chirps can be toggled ON or OFF without entering the Feature
Bank programming.
1. Turn the ignion key ON/OFF.
2. Press and release the valet buon 3x.
The system will respond with one (1) chirp for ON and two (2) Chirps for OFF. This
feature will not aect alarm trigger or programming.
User Programmable LED
System LED nocaons can be turned ON or OFF without entering Feature Bank
programming.
1. Turn the ignion key ON/OFF, ON/OFF.
2. Press and hold valet buon for ve (5) seconds.
The LED will ash 1x for ON, 2x for OFF. This feature will not aect LED ash during
programming.
Remote Start
If the remote start fails to start the vehicle, the system will ash the vehicle parking
lights to indicate the cause.
The APSRS Feature Banks can be programmed by using the valet buon and remote. To
enter Feature Bank programming:
1. Turn the ignion key to ON.
2. Press and release the valet buon 3x. System will beep and ash lights 1x for Feature
Bank 1, Remote Programming.
3. Cycle ignion key OFF/ON. System will beep and ash lights 2x for Feature Bank 2.
4. Press valet buon to cycle features. LED will ash to display feature number.
5. Press lock buon to cycle opons. System will beep to indicate opon number.
6. Cycle ignion key OFF/ON. System will beep and ash lights 3x for Feature Bank 3.
7. Press valet buon to cycle features. LED will ash to display feature number.
8. Press lock to cycle opons. System will beep to indicate opon Number.
To exit Programming cycle ignion key OFF and wait ten (10) seconds. The System will also
automacally exit programming aer sixty (60) seconds of no acvity.
The APSRS can provide OEM level security. The system will monitor all entry zones (Door,
Hood, And Trunk). When an entry zone is detected the system will beep the vehicle horn
and ash the parking lights. This feature must be acvated in Feature Bank 2, Feature 12.
Operaon
To arm the system, press lock funcon on the remote.
To disarm the system, press the unlock funcon on the remote.
Valet Override Procedure
To disarm the system without the use of a remote, turn the ignion key to ON and press the
valet buon 1x.
The APSRS does not include an RF remote kit. The RF remote kit Includes two (2) remotes,
one (1) antenna, and one (1) cable. When added, remotes must be programmed to
the system. Remote Programming is located in Feature Bank 1. To enter Remote Auto
Programming:
1. Turn the ignion key to ON.
2. Press and release the valet buon 3x. System will beep and ash the parking lights 1x.
Press the lock buon on each remote. The system will beep 1x to indicate the remote has
been programmed. If programming one (1) buon remotes, press the Start buon. Only
primary remote funcons are auto programmed. This Includes Lock, Unlock, and Trunk/
Start.
If using AUX output control, you must manually program the AUX output channels to
the remote. Please see the complete installaon guide for manual remote programming
instrucon.
Note: If programming 2-Way remotes, wait for the remote to beep before programming
addional remotes. This beep is conrmaon that a 2-Way response has been received
from the main module.
The Feature Banks below can also be programmed using the FlashLogic Weblink or Weblink Mobile.
Please visit www.FlashLogic.com for more detail.
10 Second Pulse
15 Second Pulse
20 Second Pulse
30 Second Pulse
Push & Hold
Latch ON/OFF
Latch 10min w/ RS
Latch Run�me
5 Second Pulse
1 Second Pulse
Ch. 5 AUX
Ch. 6 AUX
Ch. 7 AUX
Pulse During Crank
Accessory
Factory Arm
Factory Disarm
Ch. 4 AUX
Lock
Unlock
2nd Unlock
Trunk
Remote Start Status
Ignion
Pulse Aer Shutdown
Domelight
Headlight
Defrost
LED
REV. 1 2019 Voxx Electronics. All Rights Reserved.
Data Protocol Selecon
The default data port protocol of this model is ADS (iDatalink 2-Way). This model is capable
of detecng the correct data port protocol (ADS or DBI) and automacally conguring
Feature Bank 2; Feature 18. To inialize the detecon procedure:
1. Press and hold the valet buon.
2. Cycle the vehicle’s Ignion ON/OFF 2x.
3. Release the valet buon.
The system will automacally detect and set the correct data port protocol, ADS or DBI.
Note: This feature is only available on module rmware v2.00 or higher.
Tach Programming
The installer must manually congure the Engine Conrmaon method in Feature Bank
3, Feature 5. The default method is “Tach”. This method requires using the Green/Orange
tach input wire. When using the default “Tach” method, the vehicle tach rate must be
programmed. To enter tach rate programming:
1. Turn the ignion key ON.
2. Press and release the valet buon 3x.
3. Turn the ignion key OFF.
4. Press and hold valet buon.
5. While holding valet buon, start the engine using the key.
6. Hold the valet buon for approximately ten (10) seconds. If connected to the vehicle
Tach source, the system will ash the parking lights 1x every second.
7. Release the valet buon. The system will turn on the parking lights for two (2)
seconds to indicate the tach rate is programmed.
The tach rate can also be programmed without the use of a valet buon. This is helpful
when using the OEM remote of CarLink system to control this module. To program the tach
rate without a valet buon:
1. Turn the ignion key to the ON posion and start the vehicle’s engine.
2. Wait for Engine RPM to lower to a normal idle.
3. Press and hold the vehicle’s brake pedal.
4. Press the LOCK buon on the OEM remote or the Carlink App.
The vehicle’s parking lights will ash 7x to indicate the tach signal has been learned. If the
parking lights do not ash, locate another tach source and repeat steps 1 - 4 above.
Note: Programming tach signal via OEM or Telemacs control is only available on Firmware
v1.47 or Higher.