Prime AT PLUS User manual

1
WCDMA/GPS Tracker
ATPLUS(3G)
User Manual
Revision:1.00
DocumentTitle AT PLUS(3G)Usermanual
Version 1.00
Finale Date 2016-01-20
Status Released
DocumentControlID TRACKER AT PLUS(3G)
PDFpdfFactoryProwww.fineprint.cn

2
Contents
1 Introduction....................................................................................................................................3
2ProductOverview..........................................................................................................................3
2.1 Appearance..........................................................................................................................3
2.2 Buttons/Micro USBInterface Description..........................................................................3
2.3 LEDDescription.................................................................................................................4
3 Getting Started...............................................................................................................................5
3.1 Parts List.............................................................................................................................5
3.2 BatteryCharging.................................................................................................................5
3.3 ATPLUS(3G)DataCable...................................................................................................5
3.4 Poweron/Poweroff............................................................................................................6
4Trouble shooting andSafetyinfo...................................................................................................7
4.1 Trouble shooting.................................................................................................................7
4.2 Safetyinfo...........................................................................................................................7
PDFpdfFactoryProwww.fineprint.cn

3
1Introduction
ATPLUS(3G)isa powerfulGPSlocatorwhich isdesigned forvehicle, petsand assetstracking.
With superiorreceiving sensitivity, fastWCDMAfrequencies850/1900 and GSMfrequencies
850/900/1800/1900. Itslocation can berealtime orschedule tracked bybackend serveror
specified terminals. Based on the embedded wireless tracking protocol,ATPLUS(3G)can
communicate with the backend serverthrough WCDMAorGSM/GPRSnetwork, and transfer
reports ofemergency, Geo-fencing, device statusand scheduled GPSposition etc Service
provideriseasyto setup theirtracking platformbased on the functionalwireless tracking protocol.
2ProductOverview
2.1 Appearance
Figure 1-1
2.2 Buttons/MicroUSB Interface Description
Button /MicroUSBInterface Description
KEY/interface Description
Power Key Poweron ATPLUS(3G)
Poweroff ATPLUS(3G)(Ifpowerkeyisenabled)
Function Key
Geo-Fence mode
Long press the keyto enable/disable Geo-Fence ID0
Geo-Fence in currentposition mode
Long press the keytoenable/disableGeo-Fence ID0. If enableGeo-Fence
ID0, using the currentposition asthe centre ofGeo-Fence 0.
SOSmode (default)
Long press the keyto activeSOSalarm
PDFpdfFactoryProwww.fineprint.cn

4
Micro USB
interface Connecta 3.7VLi-ion orLi-Polymerbatterycan poweron ATPLUS(3G)
Backend serverdeveloperoradministratorcan usethe datacabletoconfigure
ATPLUS(3G)
ResetKey Click the keywill turnoff internalVBATwhenOSisabnormal,and then
press PowerKeyto restart ATPLUS(3G).
2.3 LED Description
Figure 1-2
There are fourLEDlightsin ATPLUS(3G)device, the description asfollowing.
Light Event State
Poweron and normalDarkPowerLED
Fullycharged Solid
In charging Slowflash
Poweron and normal SlowflashWCDMA
LED Poweroff Dark
WIFIon SlowflashWIFILED
WIFIoff Dark
GPSfixed FastflashGPSLED
GPShasbeen turnedoff Dark
PDFpdfFactoryProwww.fineprint.cn

5
3GettingStarted
3.1 PartsList
Name Picture Remark
ATPLUS(3G)
Locater
The WCDMA/GPS locator.
ATPLUS(3G)
Data and charger
Cable
Itthe USBdatacablewhich canbeusedfor
firmware upgrading andconfiguration.
Italso includesthe chargerinterface on the
ATPLUS(3G).
3.2 BatteryCharging
The following itemsare suggestion forbattery charge, please pay more attention.
uDuring thecharging process,the PowerLEDlight will solid. Whenthe batteryis
fullycharged, the PowerLEDlight will be Ever-light.
uYou cancharge the batteryusing USBcablewhich connectsATPLUS(3G)device
with the PC.
uCharging will lastabout5 hours.
Note:If the ATPLUS(3G)device isfirstlyused, pleasemake surethe batteryisfully
charged,which will make the life ofbattery much longer.
3.3 ATPLUS(3G)Data Cable
ATPLUS(3G)Data Cable isa cable with a MicroUSBconnector.
The USBdatacableisused fordatadownload, which will be used forfirmwareupdate
orconfiguration and can be used forcharging atthe same time.
PDFpdfFactoryProwww.fineprint.cn

6
Figure 2-1
3.4 Poweron/Poweroff
Figure 2-2
Poweron:
uPress thePowerkeyatleast3secondsandreleaseit topoweron ATPLUS(3G)
device. Note that, the PowerLEDlight will fastflash.
Poweroff:
uPressthe powerkeyabout3seconds;PowerLEDlightwill fastflashand then turn
off, which indicatesthatATPLUS(3G)device hasbeen powered off.
Note:theusercannotpower offATPLUS(3G) ifthepowerkeyisdisabled
byprotocol.
PDFpdfFactoryProwww.fineprint.cn

7
4Troubleshootingand Safetyinfo
4.1 Trouble shooting
4.2 Safetyinfo
The following itemsare suggestion forsafety use, pleasepay moreattention.
uPleasedo notdisassemble the device byyourself.
uPleasedo notputthe device on the overheating ortoohumidplace, avoidexposure
todirectsunlight.Too high temperaturewilldamage thedevice oreven causethe
batteryexplosion.
uPleasedo notuseATPLUS(3G)on the airplane ornearmedicalequipment.
Trouble Possible Reason Solution
APNiswrong. Some
APNcan notvisit the
internetdirectly.
Ask the network operatorforthe right
APN.
Messagescan’tbe
reported to the
backendserverby
Mobile network. The IPaddress orport of
the backend serveris
wrong.
Make sure the IPaddress forthe
backendserverisan identified address
in the internet.
Unable topower
off ATPLUS(3G).
The function ofpowerkey
wasdisabled by
AT+GTFKS.
Enable the function ofpowerkeyby
AT+GTFKS.
Batterycan notbe
charged
The batteryhasnotbeen
used fortoo long time and
hasbeen locked.
Using a externalpowersource with 3.6V
to 4.2VDCpowersupplytoactive the
batteryorapplyforaftersalehelp.
Pleasemove ATPLUS(3G)to a place
with open sky.
ATPLUS(3G)
can’tfix GPS
successfully.
The GPS signalisweak.
Itisbetterto letthe top surface face to
the sky. (The same surface with
indication LED)
PDFpdfFactoryProwww.fineprint.cn

FCC Statement
1. This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference
that may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
SAR Information Statement
Your wireless phone is a radio transmitter and receiver. It is designed and
manufactured not to exceed the emission limits for exposure to radiofrequency
(RF) energy set by the Federal Communications Commission of the U.S.
Government. These limits are part of comprehensive guidelines and establish
permitted levels of RF energy for the general population. The guidelines are
based on standards that were developed by independent scientific
organizations through periodic and thorough evaluation of scientific studies.
The standards include a substantial safety margin designed to assure the
safety of all persons, regardless of age and health. The exposure standard for
wireless mobile phones employs a unit of measurement known as the Specific
Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg. * Tests for
SAR are conducted with the phone transmitting at its highest certified power
level in all tested frequency bands. Although the SAR is determined at the
highest certified power level, the actual SAR level of the phone while operating
can be well below the maximum value. This is because the phone is designed
to operate at multiple power levels so as to use only the power required to
reach the network. In general, the closer you are to a wireless base station
antenna, the lower the power output. Before a phone model is available for
sale to the public, it must be tested and certified to the FCC that it does not
exceed the limit established by the government adopted requirement for safe
exposure. The tests are performed in positions and locations (e.g., at the ear

and worn on the body) as required by the FCC for each model. and when worn
on the body, as described in this user guide, is 1.234W/Kg(Body-worn
measurements differ among phone models, depending upon available
accessories and FCC requirements). While there may be differences between
the SAR levels of various phones and at various positions, they all meet the
government requirement for safe exposure. The FCC has granted an
Equipment Authorization for this model phone with all reported SAR levels
evaluated as in compliance with the FCC RFexposure guidelines. SAR
information on this model phone is on file with the FCC and can be found
under the Display Grant section of http://www.fcc.gov/ oet/fccid after searching
on
FCC ID: ZKQ-PLWAdditional information on Specific Absorption Rates (SAR)
can be found on the Cellular Telecommunications Industry Asso-ciation (CTIA)
web-site at http://www.wow-com.com. * In the United States and Canada, the
SAR limit for mobile phones used by the public is 1.6 watts/kg (W/kg) averaged
over one gram of tissue. The standard incorporates a sub-stantial margin of
safety to give additional protection for the public and to account for any
variations in measurements.
Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF
exposure requirements, a minimum separation distance of 5mm must be
maintained between the user’s body and the handset, including the antenna.
Third-party belt-clips, holsters, and similar accessories used by this device
should not contain any metallic components. Body-worn accessories that do
not meet these requirements may not comply with RF exposure requirements
and should be avoided. Use only the supplied or an approved antenna.