PrimeCables CAB-ET101 User manual

Ax8
D
4x 4
Bx8
D
3x 3
Cx8 Cx6
9
8
67
1
2
1
3
6
7
C
C
C
A
D
A
B
D
Installation guide
Item No.:CAB-ET101
Technical Data
Column Number
Maximum Load
Speed
Input Voltage
Lowest Position(with desktop)
Highest Position(with desktop)
Desktop Size
Duty Cycle
Protection Class
Applicable Temperature
Certification Standard
80KG
18mm/s
110V
750mm
1230mm
1200*600*25mm/1400*700*25mm
0~40°C
CE FCC
2
1600*800*25mm
2 minutes on, 18 minutes off
Accessory kit
Note: The drawings below are only for reference and may be slightly different with the object, please in kind prevail. Any tools missing or
installation problems, please contact the customer service freely.
Part list Installation instruction
ID Part Qty ID Part Qty ID Part Qty
STEP1:
Use 4 PCS of Hexagon Socket Button Head Screws(A) to connect “L” Marked Desk
Foot(1) and “L” Marked Desk Leg(2), and use a 4*4 Wrench(D) to fasten.
Similarly, use 4 PCS of Hexagon Socket Button Head Screws (A) to connect “R”
Marked Desk Foot (1) and “R” Marked Desk Leg (3), with arrows in the same
directions, and use a 4*4 Wrench (D) to fasten.
STEP4:
Install mounting plate(6) to “L” element of table leg by four hexagon socket
button head screws (B), then fasten them by 3x3 wrench(D). Use the same
way to install the right mounting plate(7) to the right.
Attention: Marks are in
the same direction
STEP5: STEP6:
Attention: Worksurface is optional
worksurface
Electric phillips
screwdriver
Using the 8pcs cross recessed countersunk head screw(C) to install the
worksurface with the right (6)and left(7) support plate, and tight them by
cross screwdriver or electric pistol drill.
Using the 6pcs cross recessed countersunk head screw (C) to install the control
box(8) and the handset (9) with the worksurface, tight them by cross
screwdriver or electric pistol drill. Pay attention to the installation direction of
the control box and handset, and the connecting line range, should be as what
is shown in the figure.
Attention make sure both parts ：
are heading the same direction
A
x8
M6X16mm
B
x16
M5X10mm
C D
x14
x2
St4.2X20mm
4x4
3x3 6x6
Ex1
1
21
3
4
5
6
8
9
7
1 1 1 0
1 2
1 2 3
4 5 6
7 8 9
10 11 1 2
1+1 1 1
11
1
1
2 1
1 1
6
P u t t w o h e x a g o n j o i n t l e v e r s ( 5) t h r o u g h l e f t a n d r i g h t e l e-
m e n t s o f t h e t a b l e l e g t o t w o s i d e d d r i v i n g l e v e r o f m o t o r e l e-
m e n t ( 4) , l o c k i t w i t h l o c k i n g f a s t e n e r , a s d i s p l a y e d i n t h e
p h o t o .
5
4 5
123
Install to card slot position
unscrew the plastic
nut connect driving
lever
lock the plastic nut
Use 8 PCS of Hexagon Socket Button Head Screws(B) to connect Motor
Module(4) to “L” Marked Leg Module and "R" Marked Leg Module respectively,
and use a 3*3 Wrench(D) to fasten them. Motor Module (4) needs to be installed
with Arrow label upward, do not misplace.
x8
3x 3
B
D
！
Insert driving lever to card slot
position on desk leg
shorter part
Attention: while there's
no access to install the
drive link, try to use the
6x6 wrench(E) fine
turning table legs to make
hexagon direction same
as motor element
shorter part
B
D
B
Motor Module(4) needs to be installed at
the "Shorter Part" side, with Arrow label
upward, do not misplace.
STEP3:
STEP2:

8
●“▲”
●
●
●
●
●
●
“▼”
“1”
“2”
“3”
“M”
“A”
● First reset before use, LED display shows ” ”, press”▼” and hold till
the desk goes to the lowest and then go up to 75cm, display shows” ”,
reset done.
● After reset, use ”▲”and ”▼” to adjust the desk, display shows height,
the height range is ”75cm-123cm”.
● Save:
a. Press ”up” or ”down” to your height, example” ”
b. Press ”M ”, display show” ”, then press ”1” to save the height
80.0cm to position 1, display shows” ”
c. Repeat a and b, save 100cm to position 2 and 120cm to position 3,
display shows” ”and ” ”
d. Press 1, 2, or 3 to adjust to saved heights.
● Long time sitting remind
a. Press ”A”, the remind is on, display shows” ”
b. After 2 seconds, 45 minute countdown starts, display shows” ”,
when it shows ” ”, there will be a 10 second beeping.
c. Within 10 second, press button to adjust, there will be another 45
minutes countdown, if no adjustment in 10 seconds, it will remind again
after 5 minutes. If still no adjustment, then it won't remind again.
d. Press ”A” and hold for 3 seconds to shut the remind function,
display shows” ”
9
1 1 1 0
8
1 2
STEP7:
Socket for Motor
Wire
Socket for
handset Wire Socket for Power
Line
According to the graph above, connect the handset wire (9),
Power Line (10) and Motor Wire (11) to the responding sockets in
controller box (8).
Handset Wire
To make the wires in order,
cable organizer (12) can be
used to attach the wires to
the desktop surface.
Control panel instruction
LED display
Up, adjust the desk upwards
Down, adjust the desk downwards
Position 1, first height position saved by user
Position 2, second height position saved by user
Position 3, third height position saved by user
Save, save height position
Long time sitting remind button, remind of long time sitting
Instruction
Common Faults Handling
Tips below can help you detect and eliminate common faults. If the fault happens to be not listed in the below chart, please contact the supplier. All the faults
or turnovers can only be diagnosed and corrected by manufacturer and trained professionals.
Symptoms
No reaction after long time
pressing on the button DOWN
No reaction after pressing on
the button UP and DOWN
Slow speed when goes up
The generator does not move as required
Device only goes down
Device glides
Device always resets
The lifting or falling height is
not adequate
Methods
1.Check if the connection is normal
2.Contact the supplier
1.Check if the connection is normal
2.Contact the supplier
1.Check if the device loading exceeds 80kg
2.Contact the supplier
1.Contact the supplier
1.Reset
2.Contact the supplier
1.Check if the device loading exceeds 80kg
2.Contact the supplier
1.Check if the device loading exceeds 80kg
2.Contact the supplier
1.Restart after 13 min break with power on
2. Contact the supplier
1. Hold “m” and “3” together more than 3 sec, hearing
buzzer for 2 times continuously, restore factory settings.
2. Contact the supplier
Caution：
This marking indicates that this product should not be disposed with other household wastes. To prevent possible
harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the
sustainable reuse of material resources. To return your used device, please use the return and collection systems or
contact the retailer where the product was purchased. They can take this product for environmental safe recycling.
Handset
Exceeds duty cycle
1. Power supply: AC110V±10%,60HZ
2. Service Environment: 0-40℃
3. Unplug the power plug before cleaning, wipe the dust on surface with slight wet dishcloth when cleaning, be careful not to let the
drops into the internal parts, not loose the connector.
4. The electric box contains electronic components, metals, plastics, wires etc., so dispose of it in accordance with each country's
environmental legislation, not the general household waste.
5. Check carefully to ensure correct and complete assembly before using.
6. Be familiar with all functions and program settings of the product before first use.
7. Children are forbidden to play on the product because of unforeseen action when playing, so any dangerous consequences
caused by this improper action will not be on
8. Slight noise caused by the V-ribbed belt or brake system due to structure will not have any effect on the use of the equipment.
9. Corrosive or abrasive materials are forbidden to clean the equipment. Must ensure that the cleaner used will not pollute the
environment.
10. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance
in a safe way and understand the hazards involved. Children shall not play with the appliance.
11. Cleaning and user maintenance shall not be made by children without supervision.
12. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or a similarly
qualifiedpersoninordertoavoidahazard.
13. Please make sure there is no hazard sources in your operating environment. e.g., do not litter the tools around. Always be
careful to treat the packaging materials in order to avoid any possible danger, e.g. plastic bag may lead to choking hazard to
children.
14. Keep the original package of the equipment if necessary in case of the future use in transportation.
DISPOSAL