PrimeCables ERGO Cab-PC-08143 User manual

Model：Cab-PC-08143/08144

1/16

2/16

3/16
Please make sure that cables are not damaged.

4/16
ST4.8x19
ST3.5x19
M8x16
M6x16
×9 ×9 ×3 ×3 ×4 ×9
×4 ×1 ×1 ×1
A B C D E F G
H I J
K

5/16
1.
2.
Pinch Point
Watch Your Hands
x 8
G

3.
4.
6/16
B
H
G

7/16
5.
6.
×2
×2
Open
61x6M
G
M4
×2
A
G

8/16
7.

9/16
9.
8.
×2
×2
×4
F
×2
F
61x6M
A
×2
G
M4
61x6M
G
M4
×4
A

11.
10.
10/16
IC
ST4.8*19ST3.5*19
DJ
please do not fully tighten screws
after all screws are in places.
J
I

12 .
1611/
K

13.
12/
16
E
×3

14.
13/
16

14/16
1. Basic operation of manual controller
a. Rise and fall
Hold down the hand controller keyboard,table panel rising,stop after release;
Hold down the hand controller keyboard,table panel drop,stop after release.
b.Common height of memory
When you go up and down to the height you want to store,then press the “M”
key of the hand controller for about 3 seconds，wait for the screen to flash,press
any of the buttons 1, 2, 3, 4 again,the screen stops flashing,at this time the height
of rise and fall just write it down,the top 1, 2, 3 and 4 of the hand controller
represent 4 different heights that can be stored,and it's repetitive,the memory
still exists after the power outage.
c.System reset
When an exception occurs during the use of the system,it is necessary to reset
the system to return it to its normal state.
The reset steps are as follows: Press and hold on the hand controller keyboard
five seconds later display Show“RES”,the reset starts in about 5 seconds,until it
falls to the lowest point and hears a drop and bounces,release button reset
successfully and display current height. If the table is at a certain height,you need
to hold down the on the hand controller, until it drops to the lowest point
and hears a drop and bounces,release the button and reset successfully,

15/16
and you can hear the sound of dripping again to complete the reset.If you cannot
reset, you should turn off the hand controller after the power is off, wait for the
screen light to go out safely, and then turn on the power again, first turn off the
collision function, then reset it (adjust to 0 bit), and turn on the collision function
after the reset is completed.
d.Unit switching
The product height display can be switched between cm and inch.Press and hold
the “M” and “1 ”keyboards on the hand controller for 3 seconds at the same
time, the screen flashes and displays C-E, Press keys in 10 seconds to
display“C”to switch to cm，Press keys to display “E” and switch to inch,
Press “M”to save and complete the switch.
e.Collision sensitivity adjustment
Press and hold the“M”and“2”keys at the same time, and display“3”after
5 seconds to start the sensitivity adjustment function.press and keys to
adjust，Display “0”to turn off the collision function,Display“2”indicates
slight anti-collision strength.Display “3”indicates moderate anti-collision
strength.The display of“4”indicates heavy anti-collision strength.
Press M key to save after confirmation, and complete the setting.
2. Matters needing attention in the use of products
a. The frequency of use of the product is use it for 2 minutes continuously and
rest for 18 minutes.The power supply voltage is 100-240V.
b. Products need to stay away from water and corrosive liquids.
c. If there is something wrong with the product, please do not disassemble
it privately, please contact us.

16/16
Below are the possible errors which can be dis-played.The errors
will only be dis-played when a button is pressed.
3.Specifications
4.Trouble Shooting