Pro 1 IAQ T601-2 User manual

Una versión española de este
manual puede ser descargada
en www.pro1iaq.com
This manual covers the following models:
• T601-2
® U.S. Registered Trademark. Patents pending.
Copyright © 2010 Pro1 IAQ, Inc. All rights reserved.
Mounting and Battery Installation
For assistance with this product please
visit http://www.pro1iaq.com or call Pro1
Customer Care toll-free at 888-Pro1iaq
(776-1427) during normal business
hours (Mon-Fri 9 AM - 6 PM Eastern)
Rev. 1043

3
Important:
The low battery indicator is displayed
when the AA battery power is low. If
the user fails to replace the battery
within 21 days, the thermostat
display will only show the low battery
indicator as a final warning before the
thermostat becomes inoperable.
Getting to know your thermostat
LCD
1
2Fan Switch
3System Switch
4Easy Change Battery Door
5Setpoint Buttons
1
23
4
5
Low Battery Indicator:
Replace batteries when
indicator is shown.
+1 will appear in the
display when the auxiliary
heat is active.
Indicates the current
room temperature.
Displays the user
selectable setpoint
temperature.
System operation
indicators: ON will
display when the
COOL or HEAT is on.

SUBBASE INSTALLATION

Select For C
with the jumper pin
Select ELEC or GAS
with this switch
Select delay ON or OFF
with the jumper pin
Reset button
Delay
The compressor delay will not allow the
compressor to be turned on for 5 minutes
after the last time the compressor was
on. The cooling icon will flash during the
delay period. Select OFF or ON with the
jumper pin as desired.

Adjusting the Temperature Swing
The swing setting, often called CYCLE
RATE, DIFFERENTIAL or ANTICIPATION
is adjustable. A smaller swing setting will
cause more frequent cycles and a larger
swing setting will cause fewer cycles.
There are separate swing settings for heat
and for cool. Follow the steps below to
adjust the SWING setting for heat or cool: Room Temperature Calibration
This feature allows the installer to change
the calibration of the room temperature
display. For example: If the thermostat
reads 70° and you would like it to read
72° then select +2. You can adjust the
room temperature display to ready -4°F
to +4°F above or below the factory
calibrated reading. Follow the steps
below to adjust the temperature reading:
Temperature swing, sometimes called differetial or cycle rate, can be customized for this
individual application. For most applications choose a swing setting that is as long as possible
without making the occupants uncomfortable.
PRO1 Tip
1.
2.
3.
4.
1.
2.
3.
4.
Select HEAT or COOL with the
system switch.
Hold down the and keys
together for 3 seconds.
Use the or key to adjust
the swing. The swing is adjustable
from ±02°F to ±20°F.
For example: A swing setting of
05°F will turn the cooling on at
approximately 0.5°F above the
setpoint and turn the cooling off at
approximately 0.5°F below the
setpoint. The factory default for
cooling is 0.5°F and 0.4°F for heating.
Wait approximately 10 seconds for
the thermostat to return to normal
operation.
Select OFF with the
system switch.
Hold down the and
keys together for 3 seconds.
Use the or key
to adjust the room temperature
display.
Wait approximately 10 seconds
for the thermostat to return to
normal operation.

subbase
9

10
Pro1 IAQ Inc.
1111 S. Glenstone
Suite 2-100
Springeld, MO 65804
Toll-free: 1-888-Pro1iaq (776-1427)
Toll Number (Outside the USA): 330-821-3600
Web: http://www.pro1iaq.com
Hours of Operation: Monday - Friday 9 AM - 6 PM Eastern
41ºF to 95ºF (5ºC to 35ºC)
44ºF to 90ºF (7ºC to 32ºC)
1 amp per terminal, 1.5 amp maximum all terminals combined
± 1ºF
Heating is adjustable from 0.2ºF to 2.0ºF
Cooling is adjustable from 0.2ºF to 2.0ºF
18 to 30 VAC, NEC Class II, 50/60 Hz for hardwire (common wire)
Battery power from 2 AA Alkaline batteries
32º to +105º (0º to +41ºC)
90% non-condensing maximum
4.7”W x 4.4”H x 1.1”D