Pro-Elec PELL0046 User manual

1
Infrared Ceiling Motion Sensor
Model: PELL0046

2
INSTALLATION
• Ensure the mains supply is disconnected or isolated.
• Remove the small screw that secures the transparent connector cover and remove
the cover.
• Loosen the 2 screws on the cable restraint.
• Having cut the 62mm dia mounting hole in the desired location and installed the
feed and load device wiring, pull the wiring down through the hole.
• Feed the wiring through the cable restraint and connect to the sensor as follows:
POSITIONING
• The sensor is suitable for mounting into plasterboard, sheet wood or suspended
ceiling tiles.
• Do not install into damp or conductive surfaces such as metal. It should be placed
away from any ammable materials.
• Before drilling any xing holes, check that there are no hidden obstructions behind
the mounting surface such as pipes or cables.
Please read these instructions carefully before use and retain for future reference.
This sensor must be installed by a qualied electrician in accordance with current
building and IET wiring regulations (BS7671).
IMPORTANT SAFETY INFORMATION
• This sensor is suitable for unearthed lighting ttings (Class II).
• Check that the voltage indicated on the rating plate corresponds with that of the
local network before connecting the appliance to the mains power supply.
• The sensor is suitable for connection to a 220-240V, 50Hz supply. It is designed
for permanent connection to xed wiring, which must be a suitable circuit protected
by an RCD with an operating current not exceeding 30mA and an MCB or fuse of
the correct rating.
• Avoid mounting the sensor close to heat sources such as heating vents.
• Avoid mounting the sensor above objects that may move in wind.
• It is suitable for use in an ambient temperature between -20°C and +40°C.
WHAT’S INCLUDED
• IR Sensor.
• User manual.

3
OPERATION
• When all wires are connected tighten the screws on the restraint.
• Ret the transparent connector cover and replace the screw.
Note: Before installing the sensor into the ceiling, test it’s operation and make any
adjustment to the settings (see below).
• Restore the power supply.
• Allow at least 30 sec for the sensor to initialise before making adjustments.
• There are two adjustments on the side of the PIR sensor, one adjusts the duration
the load device remains powered (TIME), the second one is to set the level of
ambient light (LUX) before the sensor switches the load.
• Some trial and error may be required to set these correctly. Turn clockwise to
increase the setting.
• To set the time duration in a well lit environment, set the LUX control to maximum
then adjust the LUX downwards to the setting required for normal operation.
• Once the setting is correct fold the spring locating clips upwards and insert the
sensor through the ceiling and allow the clips to release and clamp the sensor into
position.

4
SPECIFICATION
Input Voltage 220 - 240V AC 50Hz
Power consumption 0.5W approx
Ambient light <3 - 2000 Lux (adjustable)
Time delay Min 10 sec / Max 15 min approx (adjustable)
Rated load 300W CF/LED ~ 1200W Incandescent
Detection angle 360o
Detection range 6m (max)
Installation height 2.2 - 4.0m
Ingress rating IP20
CLEANING & MAINTENANCE
• Clean the sensor only with a soft dry cloth. Do not use any chemicals, abrasives or
solvents that could damage the casing or lens.
INFORMATION ON WASTE DISPOSAL FOR CONSUMERS OF
ELECTRICAL & ELECTRONIC EQUIPMENT.
When this product has reached the end of its life it must be treated as Waste Electrical & Electronic
Equipment (WEEE). Any WEEE marked products must not be mixed with general household waste,
but kept separate for the treatment, recovery and recycling of the materials used. Contact your local
authority for details of recycling schemes in your area.
Made in China
PR2 9PP
PO Box 13362 Dublin 2
Man Rev 1.1