Pro-gard SAFESTOP SS0005 User manual
STRONG
|
RELIABLE
|
SECURE
INSTALLATION GUIDE
pro-gard.com
800.480.6680
SS0005
VEHICLE ANTI-THEFT SYSTEM
UNIVERSAL SAFESTOP
1.800.480.6680www.pro-gard.com 2
SAFESTOP VEHICLE ANTI-THEFT
SS0005 - Universal Module Hardwire Instructions
WARNING! This unit cannot be used in vehicles with an ignition system that uses over 20
amps!
I. Disconnect battery!
II. Remove steering column cover underneath steering wheel to allow access to the ignition
wires. The ignition wires can be found behind the key switch.
III. Ignition wire setup (may have to look up ignition wires for vehicle make/model).
A. Locate Ignition Wires (These show +12V with the key in the On/Run position).
B. Locate Ignition Accessory Wires (These show +12V with the key in the On/Acc position in
combination with the accessory being activated).
C. Locate a battery source that can handle an additional 20A circuit. The Safestop unit
does NOT require an inline fuse, as it is internally fused.
IV. Making connections from Safestop to OEM wires. All connections should be soldered and
protected/covered using heat shrink or electrical tape tubing.
A. Cut the Ignition 1 wire in half and solder the the WHT/BLK wire from the Safestop unit into
the Ignition 1 wire that leads towards the key switch. Solder the YEL wire from the Safestop
unit into the other side of the Ignition 1 wire that leads back towards the main harness of the
vehicle.
B. Cut the Ignition 2 wire in half and solder the the YEL/WHT wire from the Safestop unit into
the Ignition 2 wire that leads towards the key switch. Solder the GRN wire from the Safestop
unit into the other side of the Ignition 2 wire that leads back towards the main harness of the
vehicle.
C. Cut the Ignition 3 wire in half and solder the the ORG wire from the Safestop unit into the
Ignition 3 wire that leads towards the key switch. Solder the WHT wire from the Safestop
unit into the other side of the Ignition 3 wire that leads back towards the main harness of the
vehicle.
D. Some vehicles may have up to four ignition wires. If this is the case, the BLU/WHT and BLU
wires on the Safestop unit can be used to splice a fourth ignition wire or to power additional
vehicle accessories. The YEL/BLK and YEL wires on the Safestop unit can also be used to
power additional vehicle accessories.
V. Powering the Safestop unit.
A. Locate the RED wire on the Safestop unit, and attach it to a +12V Battery source, making
sure that the source is fused at 15 Amps.
1.800.480.6680www.pro-gard.com 3
SAFESTOP VEHICLE ANTI-THEFT
B. Locate a solid spot on the chassis to ground the module, and attach the BLK wire on the
Safestop unit to this point. It is not recommended that this wire share a ground with any other
component.
C. Locate the Brakelight output wire (This shows +12V with the key in the On/Run position in
combination with the brake pedal being depressed). Do NOT cut this wire. Instead, strip away
a portion of the plastic insulation, exposing the copper wire, and attach/solder the GRN/WHT
wire from the Safestop unit. Cover with an insulator to prevent shorting.
D. The BRN wire is a +12V source that only supplies +12V when the key is in the ignition, in
the on position. This can be used to power gun locks or other accessories that only need
power when the key is in the ignition.
IMPORTANT Cover ends and secure all unused wires to the harness!
Drill a ¾” hole for the Safestop switch (provided).
We recommend the spot for this switch to be in plain view in a cosmetically friendly surface.
Attach switch harness ( provided ) and test unit.
NOTE: The wires must be placed back in the same locations that they were removed from.
i.e. Pink = Pin #1, Purple = Pin #2, Orange = Pin #3 on switch.
After test verication it is recommended that the Safestop module is mounted securely and
tightly to a solid location in or around the steering column.
1.800.480.6680www.pro-gard.com 4
SAFESTOP VEHICLE ANTI-THEFT
KEY IN
IGNITION 1 WIRE
IGNITION 2 WIRE
IGNITION 3 WIRE
WHT/BLK
YEL/WHT
ORG
WHT
GRN
YEL
IGNITION 3 WIRE
IGNITION 2 WIRE
KEY IN
IGNITION 1 WIRE
YELLOW & YELLOW/BLACK OPTION #2 DISABLE
(CUT OPTIONAL ACCESSORY #2 WIRE AND
CONNECT IN-LINE WITH ACCESSORY WIRE)
BLUE & BLUE/WHITE OPTION #1 DISABLE
(CUT OPTIONAL ACCESSORY #1 WIRE AND
CONNECT IN-LINE WITH ACCESSORY WIRE)
ON/OFF TOGGLE SWITCH
(DRILL 3/4" HOLE TO INSTALL)
BLACK WIRE = GROUND
RED WIRE = +12V CONST. BATT.
GREEN/WHT WIRE = +12V BRAKE SIGNAL
BROWN WIRE = +12V GUN LOCK OUTPUT
ON/OFF HARNESS
ACCESSORY HARNESS
SAFESTOP CONTROL MODULE
(KEY IGNITION
SWITCH SIDE)
(VEHICLE HARNESS
SIDE)
SPLICE CONNECT TO HARNESS
Table of contents
