Classic Accessories 52-065-010404-00 User manual

Questions, problems, missing parts? Before returning to your retailer, call Classic Accessories customer service at
1-800-854-2315, 8a.m. - 4p.m., PST, Monday-Friday. Email: [e-mail]
WARNING
READ YOUR INSTRUCTIONS COMPLETELY AND CAREFULLY BEFORE ATTEMPTING TO SET UP YOUR
NEW SNOWTHROWER SHIELD OR OPERATE YOUR SNOWTHROWER WITH YOUR SHIELD INSTALLED.
English (page 01)
Français (page 15)
Español (página 29)
12cH56_12797
ITEM/ARTICLE/ARTÍCULO: 52-065-010404-00
SNOW THROWER SHIELD

2
TABLE OF CONTENTS
Safety Information................................................................................................................................................................................... 2
Package Contents List (Parts and Hardware)............................................................................................................................................ 3
Tools Needed ........................................................................................................................................................................................... 3
Assembly Time......................................................................................................................................................................................... 3
Package Contents List (Soft Parts)........................................................................................................................................................... 4
Assembly Instructions .........................................................................................................................................................................5-13
Care and Maintenance.............................................................................................................................................................................14
Troubleshooting......................................................................................................................................................................................14
Warranty.................................................................................................................................................................................................14
Replacement Parts..................................................................................................................................................................................14
SAFETY INFORMATION
Please read and understand this entire manual before
attempting to assemble, operate or install the product. If
you have any questions regarding the product please call
Classic Accessories customer service at 1-800-854-2315,
8a.m. - 4p.m., PST, Monday-Friday.
1. THE SHIELD IS NOT A PROTECTIVE DEVICE.
The shield will NOT protect against noise, engine exhaust,
chemicals, collision, roll-over or other accidents.
2.Follow all your snow thrower manufacturer’s
recommended safety instructions.
3.Operating a snow thrower with this shield will restrict
your field of vision. Watch carefully for people, children,
obstructions or obstacles.
4.The shield adds height to your snow thrower. Remember
the height of your shield. Watch carefully for tree limbs or
other items overhead that you could previously go under
without a shield.
5.Before use be sure that all bolts are tight. If one or more
bolts comes loose failure of shield parts may occur.
PRACTICE SAFE MAINTENANCE
 
 
 
 
dangerous carbon monoxide fumes can collect.
 


 
 
from any moving parts, to prevent them from getting
caught.
 

 

Replace all worn or damaged safety and instruction
decals.


 
modifications to the machine or attachment may impair its
function and safety.
WEAR APPROPRIATE CLOTHING
 
 

 
 
 

3

START ASSEMBLY ON PAGE 4
Part Description Quantity
ALeft Base Bar 1
BRight Base Bar 1
CMounting Post Lower, Left 1
DMounting Post Lower, Right 1
EMounting Post Center 2
FMounting Bar Top, Left 1
GMounting Bar Top, Right 1
HShield Fabric Shell 1
I Long Hoop Support Pole 1
JLong Hoop Support Pole 1
Part Description Quantity
KShort Hoop Support Pole 1
LShort Hoop Support Pole 1
MSmall Loop Clamp 2
NHex Bolt - short 2
OLarge Loop Clamp 2
PSmall Loop Clamp - coated 2
QHex Bolt - long 2
RHex Nut 2
SNon-slip PVC 1
TCounter Balance Bag 1
1/2in. Box Wrench Adjustable Wrench 1/2in. Socket Wrench
TOOLS NEEDED
OROR
ASSEMBLY TIME
15 Minutes
A
C
B
D
E
FG
J
L
I
P
M
N
OQ
R
T
SH

4
PARTS NEEDED TOOLS NEEDED
Insert mounting post lower left [C] onto the end of left base
bar [A] until spring button pops through hole.
Insert mounting post lower right [D] onto the end of right
base bar [B] until spring button pops through hole.
Slide mounting posts [A, B] together until spring button pops through hole.
1
3
2
4
ASSEMBLE THE FRAME (FIG. 1-9)
Note: Assemble frame on a clean flat surface next to your snow thrower for easy mounting.
STEP 1
NONE
Inside view
A
A B
C D
C
D
C
B

5
PARTS NEEDED TOOLS NEEDED
5
ASSEMBLE THE FRAME (FIG. 1-9)
Note: Assemble frame on a clean flat surface next to your snow thrower for easy mounting.
Insert both mounting post upper [E] onto upright studs on lower
mounting [C, D] until spring button pops through hole.
NONE
STEP 1continued...
+
C
D
EE
E

6
PARTS NEEDED TOOLS NEEDED
Attach top mounting bar assembly [F, G] to the top of mounting posts
[E] until spring button pops through holes. Make sure the stub tubes
are facing the same direction as the stub tubes on [C, D].
Make sure the stub tubes on [F, G] are facing the same
direction as the stub tubes on [C, D].
Slide top mounting bars [F, G] together until spring button pops through hole.
6
8 9
7
ASSEMBLE THE FRAME (FIG. 1-9)
Note: Assemble frame on a clean flat surface next to your snow thrower for easy mounting.
STEP 1continued...
NONE
+
G
F
G G
E
D D
F
G
F F
E
C C

7
PARTS NEEDED TOOLS NEEDED
Insert the longer flexible rod into the slip pocket at the bottom of the shield shell.
Repeat with the shorter rod into the slip pocket at the top.
Make sure about 1inch of the rod is showing.
3
1 2
ASSEMBLE THE FRONT SHIELD (FIG. 1-4)
WARNING: Use care when assembling the poles. Poles under tension can slip out of the metal/plastic sleeves causing serious

Insert one long hoop pole [I] into [J] to assemble the lower support rod.
Repeat with remaining short hoop poles [K] into [L], to make a separate
upper support rod.
Lay out the shield shell [H]. Locate the two small slip through
pockets on the inside of the shield fabric shell.
NONE
STEP 2
4
I J
I
L
J
H
H

8
PARTS NEEDED TOOLS NEEDED
Pull the top of the snow shield down over the top of the upper mounting posts [F,G].
Insert one end of the longer flexible [I,J] support rod into
the lower stub tube connecting [C] to [D].
Repeat step and insert one end of the shorter flexible [K,L]
support rod into the upper stub tube connecting [F] to [G].
Firmly insert the support pole completely into the stub tube.
Carefully flex the opposite end of rod [I, J] and [K, L]
down and into position in opposite stub tubes.
1 2
43
STEP 3
INSTALL THE FABRIC SHIELD SHELL ONTO THE METAL FRAME (FIG. 1-6)
Note: Fabric shell will be tight when properly assembled.
NONE
+
H
I
C
C
G
G
D
F
F

9
PARTS NEEDED TOOLS NEEDED
5 6
INSTALL THE FABRIC SHIELD SHELL ONTO THE METAL FRAME (FIG. 1-6)
Note: Fabric shell will be tight when properly assembled.
Tighten up the skin by closing around the support bars all of the
rip-n-grip strips on both sides and at the bottom of the frame.
NONENONE
STEP 3continued...

10
PARTS NEEDED TOOLS NEEDED
Slide on the small loop clamp [M] onto the two open spaces
on the lower part of the shield frame [A,B].
Secure small loop clamp [M] with hex bolt [N].
1 2
3
ATTACH THE MOUNTING SYSTEM TO YOUR SNOW THROWER SHIELD (FIG. 1-3)
Note: Exact positioning may vary depending on your machine.
STEP 4
1/2 in. Box
Wrench
OR
OR
1/2 in. Socket
Wrench
Adjustable
Wrench
+
M
N
M
A
A
B
M
N

11
PARTS NEEDED TOOLS NEEDED
+
1
OPTIONAL 2aOPTIONAL 2b
2
ATTACH THE MOUNTING SYSTEM TO YOUR SNOW THROWER FRAME (FIG. 1-2)
Note: Exact positioning may vary depending on your machine.
Note: In some instances, it may be necessary to mount the loop clamps [L] or [M] above the handlebar crossbar support. This will help the
assembled shield sit higher for added protection.
Select either the small loop clamp [P] set or the large loop clamp [O] set and
check to see which clamp can slip onto the snowthrower handlebar uprights.
Note: You will only need one set of either [O] or [P] for this step. Use the part
that will provide the most secure fit when placed around the snowthrower
upright. If both [O] or [P] are loose follow the optional step shown below.
Select either the small loop clamp [P] set or the large loop clamp [O] set and
check to see which clamp can slip onto the snowthrower handlebar uprights.
Optional mounting:
Use supplied non-slip PVC [S] to cover side mounting bars.
Wrap material around side mounting bars.
NONE
STEP 5
O
O
O
S
O
P
S
R
Q

12
PARTS NEEDED TOOLS NEEDED
Fill the counter balance bag
[T] with extra weight.
Weight Options: Sand, Kitty litter, etc.
Weight Not Included
Roll the top of the counter balance
bag [T] down. Fold the rip-and-grip
strips behind the bag and secure
together the rip-and-grip strips.
Slide on the hook end onto the top edge of your snowthrower.
Wrap the tensioning strap around a support bar, then connect. Use the counter balance bag [T] to keep snow thrower from tipping back when
mounting the assembled snow shield onto the snow thrower in Step 7.
1 3
4 5
2
ATTACH THE COUNTER BALANCE BAG TO YOUR SNOW THROWER (FIG. 1-5)
Note: Exact positioning may vary depending on your machine.
Exact weight may vary depending on your machine.
STEP 6- for lighter weight machines
NONE
+ +
T
TLBS

13
PARTS NEEDED TOOLS NEEDED
Lift your pre-assembled shield and align the two loop clamps. Insert Hex bolt [Q] through both loop clamps [M] & [O].
Repeat on the other side.
1
3
2
4
1/2 in. Box
Wrench
OR
OR
1/2 in. Socket
Wrench
Adjustable
Wrench
MOUNTING THE FRAME (FIG. 1-4)
STEP 7
Tighten down the Hex nut [R].
Tighten down until the shield sits at the preferred angle.
R
Q
+ +
M
OQ
Q
P

14
22640 68th Ave. S. Tel: [phone]
Kent, WA, USA 98032 Fax: [phone]
www.classicaccessories.com
Email: [e-mail]
©2012 • 12cH56_12797
CARE AND MAINTENANCE
STORAGE
Store in a clean dry place. Never store a wet shield in an enclosed area as it can develop mildew.
Avoid folding the plastic windows of the cover for long periods.
BOLTS
Check all bolts before each use to see that they are tight. If one or more bolts come loose, failure of shield parts may occur.
WINDOWS
Don't clean the plastic windows when they are dry—you can scratch them.
Hose them with water and rub them with your bare hands. Liquid soap may be used.
During freezing weather an automotive windshield cleaner and a soft cloth will work (don't use your bare hands with the cleaner).
Fabric areas of the shield may be washed with a rag. Don't use soap as it may remove protective coatings added by the factory.
TROUBLESHOOTING
ONE YEAR LIMITED WARRANTY
The manufacturer, Classic Accessories, Inc., will repair or replace, without charge, this product which under normal usage has proven to
be defective in its manufacture or workmanship for a period of one (1) year from the date of initial retail purchase. This warranty is valid
only to the original purchaser. This warranty is not transferable and does not cover any parts that have been subjected to misuse, abuse,
alteration, overload, accident or normal wear of moving parts.
Service can be obtained by contacting Classic Accessories at 1-800-854-2315. Any shield or shield part that is returned to Classic
Accessories, together with the original sales receipt as proof of initial retail purchase, and with postage prepaid, will be repaired or replaced
without cost if the unit is found defective. This warranty does not apply to accessories or damage caused where repairs have been made or
attempted by others. All warranty work will be completed in a reasonable time, not to exceed 60 days after receiving the product.
Classic Accessories is not responsible for direct, indirect, incidental or consequential damages. Some states and provinces do not allow
limitations on how long an implied warranty lasts and/or do not allow the exclusion or limitation of incidental damages, so the above
limitations may not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to
state and province to province.
WARRANTY VOID IF PRODUCT USED FOR COMMERCIAL OR RENTAL PURPOSES OR IF THE SNOW THROWER SHIELD IS TRANSPORTED ON AN
OPEN TRAILER OR TRUCK.
Call: 1-800-854-2315 for Warranty Assistance, Monday - Friday 8:00 a.m. - 4:00 p.m., PST
REPLACEMENT PARTS
If parts are missing or if you need replacement parts, please call Classic Accessories customer service at 1-800-854-2315,
8a.m. - 4p.m., PST, Monday-Friday. Please refer to the Package Contents List for the parts list.
Problem Possible Cause Corrective Action
Shield front interferes with the
snow thrower controls.
Upper horizontal mounting bar
[A, B] is mounted too low.
1. Rotate shield forward.
2. Move shield sideways.
Shield is too low or
too close to your head.
Upper horizontal mounting bar
[A, B] is mounted too low.
1. Rotate shield forward.
2. Raise attachment point.