Pro-Ject Audio Systems Box RS User manual

INSTRUCTIONS FOR USE
Pro-Ject Phono Box RS

© Pro-Ject Audio Systems · Pro-Ject Phono Box RS · Revision 2014.10.27
2
Dear music lover,
thank you for purchasing a Pro-Ject Audio Systems phono amplifier.
In order to achieve maximum performance and reliability you should study these instructions for use carefully.
!
Warning of a hazard for the user, the unit or possible misuse.
Important notice.
Safety instructions
!
AC outlet voltages vary from country to country. Before connecting to the mains, make sure that the
voltage in your area meets the voltage requirements printed on the power supply.
The power supply is used to disconnect the unit from the mains. Make sure that the power supply is easily
accessible at all times. Never handle the device, the power supply while your hands are wet or damp.
Avoid letting liquids enter the device or the power supply. Never place any item containing liquid,
such as a flower vase on or near the device. Never spill any liquid on the device or the power supply.
Never place any naked flame sources, such as lighted candles on or near the device. The product shall not
be used in damp or wet locations, next to a bathtub, sink, swimming pool or any other similar conditions.
Front panel controls
1200
1100
1000
700
400
200
150
130
100
60
30
20
10 Ohm
To switch on from standby or to standby
The rocker switch on the left hand side of the front panel turns the unit on or back into standby. The blue LED
above the stand-by switch shows that the unit is switched on.
!
Caution! To avoid `Click´ or `Pop´ sounds, that could damage speakers or amplifiers, MUTE must be
engaged, befiore switchging the unit on or into standby.
Mute
ON/MUTE activates and deactivates mute
Selecting the de-emphasis curve
RIAA /DECCA selects the desired mode
Settings
Use the dip switches at the back of the unit and the rotary control at the front to set input capacitance and
input impedance. Please set both channels equally.
!
To alter settings MUTE must be engaged. Input impedance setting (variable) can be done while listening.

© Pro-Ject Audio Systems · Pro-Ject Phono Box RS · Revision 2014.10.27
3
Examples of typical settings
Ortofon 2M Red (MM)
gain 40dB,
input capacitance 200pF,
input impedance 47kohms.
The rocker switch F/Vmust be set to F.
The rocker switch on the right hand side sellects
the input gain.
100pF 100pF
220pF
10R
47k Fixed
ON
2 3 42
1
+
+
Ortofon X5-MC (High-Output MC)
gain 50dB,
input capacitance 420pF,
input impedance 47kohms.
The rocker switch F/Vmust be set to F.
The rocker switch on the right hand side sellects
the input gain.
100pF 100pF
220pF
10R
47k Fixed
ON
2 3 42
1
+
+
Ortofon Quintet Black (Low-Output MC).
* Input capacitance is irrelevant for low-output MC cartridges
gain 60dB,
input capacitance *,
impedance 7ohms.
The rocker switch F/Vmust be set to V.
The rocker switch on the right hand side sellects
the input gain.
+
+
1200
1100
1000
700
400
200
150
130
100
60
30
20
10 Ohm
Alternative setting with with fixed input impedance. Setting for Low-Output MC cartridges with a
recommended input impedance of ≤10 Ohm.
gain 60dB,
input capacitance *,
impedance 10ohms.
The rocker bswitch F/Vmust be set to F.
The rocker switch on the right hand side sellects
the input gain.
100pF 100pF
220pF
10R
47k Fixed
ON
2 3 42
1
+
+

© Pro-Ject Audio Systems · Pro-Ject Phono Box RS · Revision 2014.10.27
4
Gain
Gain for the RCA outputs (RCA) can be set to 60, 50 or 40dB. Gain will be 6dB higer, using the XLR outputs
(XLR).
RCA
XLR
60 66
50
40
56
46
!
Do not connect RCA and XLR outputs simultaneously.
Input impedance, variable –low-output MC cartridges
* Input capacitance is irrelevant for low-output MC cartridges
The rocker switch F/Vmust be set to V
1200
1100
1000
700
400
200
150
130
100
60
30
20
10 Ohm
Input capacitance, variable –high-output MC and MM cartridges
The rocker switch F/Vmust be set to F
100pF 100pF
220pF
10R
47k Fixed
ON
2 3 42
1
ON
200pF 300pF 420pF 520pF
2 3 42
1
ON
2 3 42
1
ON
2 3 42
1
ON
2 3 42
1
ON
100pF
2 3 42
1
Input impedance, fixed –low-output MC cartridges
* Input capacitance is irrelevant for low-output MC cartridges
The rocker switch F/Vmust be set to F
10ohms
ON
2 3 42
1
100pF 100pF
220pF
10R
47k Fixed
ON
2 3 42
1
To find out which type your cartridge is, please consult the literature accompanying your cartridge.
The literature for cartridges should also specify the correct input impedance (low-output MC
cartridges) and the correct input capacitance (high-output MC and MM cartridges), into which the
cartridge is designed to work. If in doubt please consult your dealer.

© Pro-Ject Audio Systems · Pro-Ject Phono Box RS · Revision 2014.10.27
5
Connectors
Subsonic
Filter
ON
OFF
Pro-Ject Audio Systems, Vienna, Austria
Right Left
InputOutput Output
Input
100pF 100pF
220pF
10R
47k Fixed
100pF 100pF
220pF
10R
47k Fixed
RCA
XLR
Power
2x18V=
PUSH
PUSH
!
Make all connections whilst the phono amplifier is disconnected from the power supply.
Take care to connect the left and right channels correctly. The right channel is usually marked red, the
left channel black or white.
Do not connect the phono amplifiers output to a phono input (sometimes labelled gram, disc or RIAA)
on the amplifier. Do not connect RCA and XLR outputs simultaneously.
Wiring XLR sockets: 1 ground, 2 “hot” and 3 “cold”.
Never use any other power supply than the one supplied with the unit.
Selecting input connectors
RCA/XLR select the input connectors to be used
Subsonic Filter
Subsonic Filter ON/OFF activates and deactivates the filter
Connecting the record player
Connect the tonearm signal lead to the Input of the phono amplifier. The earthing wire may be connected to
the screw terminal if you encounter hum problems when using the record player.
Connection to the amplifier
Connect the Output of the phono amplifier to a line input (such as AUX, CD, Tuner, Tape or Video) on your
amplifier.
Mains power connection
Connect the low voltage plug from the power supply to the Power 2x18V socket of the phono amplifier
before connecting the power supply to the mains.

© Pro-Ject Audio Systems · Pro-Ject Phono Box RS · Revision 2014.10.27
6
Technical specifications Pro-Ject Phono Box RS
ATypical for low output MC cartridges, Btypical for MM or high output MC cartridges
* Input capacitance is irrelevant for low-output MC cartridges
Input impedance, variable: stepless 10ohms - 1.200ohms A
Input capacitance/impedance:, variable: 100pF, 200pF, 300pF, 420pF and 520pF */47kohms B
Input impedance, fixed: 10ohms A
Input gain (+ 6dB using XLR sockets): 40dB and 50dB B / 60dB A
Noise floor: 91dB (A weighted)
THD: 0,019%
De-emphasis curves accuracy: 20Hz - 20kHz / max. 0,3dB
Subsonic filter: at 20Hz with 12dB/octave
Input: 1 pair RCA/phono sockets, 1 pair XLR sockets
Line-level output: 1 pair RCA/phono sockets, 1 pair XLR sockets.
Wiring XLR sockets: 1 ground, 2 “hot” and 3 “cold”
Outboard power supply: ±18V/250mA DC, suitable for your country's mains supply
Power consumption: 150mA DC, <1W in standby
Dimensions W x H x D (D with sockets): 206 x 72 x 200 (210)mm
Weight: 2.000g without power supply
Potential incorrect use and fault conditions
No signal on one or both channels:
No connection between player and phono amplifier or amplifier. This could be due to a faulty plug,
broken wire or solder joint or simply loose plug/socket connection.
Strong hum:
No earth connection from cartridge or arm, or arm cable to phono amplifier, or earth loop.
Output too quiet or too loud, or distorted:
Input gain incorrectly set - input overloading or insufficiently amplified.
Service
Should you encounter a problem which you are not able to alleviate or identify despite the above information,
please contact your dealer for further advice. Only when the problem cannot be resolved there should the
unit be sent to the responsible distributor in your country.
Warranty
The manufacturer accepts no responsibility for damage caused by not adhering to these instructions
for use. Modification or change to any part of the product by unauthorized persons release the
manufacturer from any liability over and above the lawful rights of the customer.
Safety instructions
!
AC outlet voltages vary from country to country. Before connecting to the mains, make sure that the
voltage in your area meets the voltage requirements printed on the power supply.
The power supply is used to disconnect the unit from the mains. Make sure that the power supply is easily
accessible at all times. Never handle the device, the power supply while your hands are wet or damp.
Avoid letting liquids enter the device or the power supply. Never place any item containing liquid,
such as a flower vase on or near the device. Never spill any liquid on the device or the power supply.
Never place any naked flame sources, such as lighted candles on or near the device. The product shall not
be used in damp or wet locations, next to a bathtub, sink, swimming pool or any other similar conditions.
Copyright
PRO-JECT is a Registered Trademark of H. Lichtenegger.
This guide was produced by: Pro-Ject Audio Systems
Copyright ©2014. All rights reserved.
The information was correct at the time of going to
press. The manufacturer reserves the right to make
changes to the technical specification without prior
notice as deemed necessary to uphold the ongoing
process of technical development.