PRO.SIS.TEL. PST-40VF Installation guide

Vertical HF monoband antenna PST-40VF
Assembling instructions:
After unpacking antenna, you will find the main lower tubes Od 40mm having Male-female plug-in
connection and upper parts of telescopic tubes pre-assembled already, following step down
diameter.
ilting it down, do in the way to have all tubes heads coming out from the main tube.
he fastening of the elements takes place by inserting the bolt from the wider hole side so that the
bolt cylindrical head passing thoroughly, sit and rests on the inner tube.
Assembly the telescopic tubes joints as in the picture below.
Lightly lubricate the threads of all bolts before installing the SS tends to be nailed very easily).
ighten the nut. Make sure that all bolt heads are on the same side.
Using the same way, extract and connect all sections, less than the larger diameter that has to be
assemblend before on the antenna base and then proceed to final assembly.
Some sections of tubing and the tip, have multiple holes that serve to make a fine tuning. Longer
element lower frequency, shortening element increase frequency.
After completing the assembly of the radiator, proceeding to the assembly of the base which
presents a whole series of holes, which have to be equipped and prepared following the pictures
sequence.
Install the 8 bolts 4x25MA in the holes in X shape and 4x16 bolt in the side hole as pictures.

Correct assembling sequence for all the bolts: bolt, serrated washer, normal nut, two flat washers
and self-locking nut. Lock all tightening bolts thoroughly normal nut. On this bolts will take place wire
radial ends.
Continue the assembly with the two insulators in which is placed the wider and lower pipe section
40mm. Leave loose bolts so you can easily move the tube into its final position with the lower side
protruding approximately 2cm from the insulator. Install on the tube end a 4x20MA bolt and lock it,
insert a flat washer, eyelet RF wire, another flat washer and normal nut. Lock bolts of isolators and
assembling the RF choke coil (choke). Making sure that the coil is vertical for a better rain
drainage. he choke will short to ground any electrostatic discharge and will reduce noise.
he care and precision of this assembly will ensure a long life to the antenna.
Check that all bolts have been properly secured and completed the radiator assembly.
With the aid of the U bolts, install the base on the supporting pole and install the wire radials.
he U bolts are 50mm wide, it can get poles or tubes from 40 to 50mm.
As radials being installed, take care doing the work as they can also heavily influence the final
tuning. You may have to try to attempt the best point of risonance.
Antenna alluminum main parts.

WARNING!!
All images and drawings, in this user manual, are indicative, with the sole purpose of helping
the assembly, they may not explain exactly the product, which may be subject to changes
without obligation to anyone, without prejudice to the final specifications.
Due wire radials antenna will have greater performance if installed 10-20cm over the ground with
radial on the soil or roof. If the space is not enought for a complete wires extension, they can be
coiled on the ground around the antenna base in a spiral-shaped design.
Before to rise up antenna in the sky, make sure that all bolts and connections are well tightned.
Do not seal traps and tubes.
Install guy wires on 20mm tube as suggested in the picture below and make sure
to install them at 120 degrees, 4-5m or more, away from the antenna base.
Technical specifications:
Height: 10.5 m approximately
Weight = 6.5Kg
Wind area = 0.2m2
ax wind = 130 km/h with guy wires
Accept mast 40-50mm (60mm on request)
6060T6 aluminum, stainless steel bracket and bolts.
Note: antenna could be influenced due local environments.
If possible avoid to install it close to metal object parallel to antenna radiator.
The antenna length can change in according with setting and/or possible environmental influences
Average usable bandwidth if swr = 1:1):
40m = ~ full band with swr <=2:1 on the band limits
Specifications may change without notice.

Warning:
Do not install the antenna near power lines or equipment that could result in electrical
contacts. You could be seriously injured or killed.
he antenna must be installed in accordance with local/national rules/laws.
If necessary get a professional installer.
Prosistel can not be sued for damages for non-compliance of equipment safety rules.
Dear customer,
thank you for purchase a Pro.Sis.Tel. item, if you are happy with it please talk to
everybody, if you are unhappy with it please talk with us.
Your feed back and suggestions, will be very appreciated, to improve our products.
Annamaria Fiume
IK7MWR
MADE IN ITALY
Protect your environment, in case of discontinuing of this unit, consign it to specialized
metal waste collector.