process-informatik EtherSens Energy User manual

Handling-Short Instruction for
EtherSens-devices / MONI V1.0
The EtherSens devices and MONI are data loggers according to their specification. Either for digital or analog
input- and output-signals, energy data or just as a pure messenger.
Commissioning of the device :
- EtherSens Bridge, EtherSens Control, MONI:
Connect the voltage 2 V DC ± 20% to the labeled terminal connectors + 2 V and GND
- EtherSens Energy, EtherSens Energy II, MONI:
Connect the voltage 230V AC to the labeled terminal connectors L1 and N.
The device starts up now, you will see the status of the device on the two-color illuminated LED display :
Green ON device ready
OFF device executes a restart or is powered off
Red ON device is booting
flashing at device boot device is updating the firmware
flashing 0,5 Hz device is logging data
fast flashing output of error codes (see below)
List of error codes:
1x flash: Initialization error of a sensor.
2x flashes: Space on the SD card smaller than 1 Kilobyte
or SD card removed without logging off.
3x flashes: Error at last mail transfer (SMTP).
x flashes: Error at last time adjusting (NTP).
5x flashes: No network connection available (only when there isn’t a connection to the
Access-Point and no LAN link state available).
When you want to reset your device (factory settings) you can press the reset button for 3s to 10s while the
device is booting. The button must be pressed with the help of a paperclip and can be found on the bottom / back
of the device.

All EtherSens devices have a build in LAN and WLAN interface. The interfaces can be used at the same time.
WLAN-communication
The WLAN interface of the EtherSens devices/MONI creates an own network and working as Access Point
from factor state. To connect our PC / Laptop to the network, open the network search and look at the network
list.
Under the shown networks there should be a WLAN network named “EtherSens WiFi”. Now ou can connect to
it. To access the website of the device ou ma be have to change the network settings from our PC. If ou have
DHCP enabled, EtherSens gives our PC an IP address from the range 192.168.1.100 to 192.168.1.199.
Alternativel ou can give our PC a manual IP address which comes from the subnet 192.168.1.xxx. The IP
address 192.168.1.58 can’t be used because it’s the default IP address of the WLAN interface of the EtherSens.
On the web server ou can change the settings for the WLAN interface. Thus ou can connect the EtherSens
with another Access-Point in our network. Furthermore it’s possible to disable the complete WLAN interface.
The WLAN module supports the channels 1 to 11 and can thus be used in Europe, America and other countries.
Important:
If EtherSens can’t connect with your Access-Point please chec if your Access-Point opens a networ
within the channel range named above. If the Access-Point opens a networ in channel 12 or 13 please
change the channel from your Access-Point.
LAN-communication
Connect the RJ45 plug from our PC with the RJ45 plug from our EtherSens device. Either ou choose a patch
cable or a cross link cable (with crossed pins). This is possible because the EtherSens device supports the Auto
MDIX technolog and can detect the transmit and receive direction b itself.
After the ph sical connection is done the EtherSens device can distribute an IP address to our PC. If ou don’t
want to activate DHCP on our PC, ou can give our PC an IP address from the subnet 192.168.1.xxx (range
from 192.168.1.1 to 192.168.1.254). Do not give our PC the IP address 192.168.1.59, because this IP address is
used b the LAN interface of the EtherSens.
Opening the device web-page
To open the web-server of the device ou have to open our browser and tip in the IP address of the LAN or
WLAN interface.
for WLAN: 192.168.1.58
for LAN: 192.168.1.59
Now the web-server of the EtherSens-device/MONI should show up with the following start-screen:
The view of the start page can vary by different device types or versions.
The picture above shows the start page of a EtherSens Energy device.
More about the EtherSens-devices/MONI as well as the current device manual or the current firmware file can
be found under

Under the web-address https://www.process-informatik.de are product specific
documentations or software-driver/-tools available to download.
If you have questions or suggestions about the product, please don’t hesitate to contact us.
Process-Informatik Entwicklungsgesellschaft mbH
Im Gewerbegebiet 1
DE-73116 Wäschenbeuren
[phone]
[email protected]
https://www.process-informatik.de
Copyright by PI - 2020
9200-D-24V
QR-Code Website:Menutree Website:
+ Products / docu / downloads
+ EtherSens Control 24V Digital-IO
Please make sure to update your drivers before using our products.

Current S7 panels via WLAN to the S5 controller
Verbinden Sie jedes S7-TCP-IP Panel mit Ihrer S5.
Jetzt auch direkt per WLAN für mobile Arbeitsplätze.
PARALLEL können mehrere Panels und sogar gleichzeitige PG-Verbindungen gefahren
werden.
Binden Sie so auch schwer zugängliche Stellen in Ihr ERP-System ein.
Integrated web-server
Observe the collected information on the integrated web-server of _MONI_ with your
mobile-phone or tablet. Change the parameterization of _MONI_, operate and control the
_MONI_ easily via the web interface.
Of course you can also operate wired, where you put the _MONI_ in your network.
Parallel operation of LAN and Wifi is also possible.