PROCET PT-PIS4PB1S-M User manual

ＰＴ－ＰＩＳ4ＰＢ1Ｓ－Ｍ Ｓｗｉｔｃｈ
WWW.PROCETPOE.COM
Ｕｓｅｒ Ｍａｎｕａｌ
Ｏｖｅｒｖｉｅｗ
Ａｐｐｅａｒａｎｃｅ
Ｄｅｃｌａｒａｔｉｏｎ
PT-PIS4PB1S-M, an industrial 4-port PoE switch with Managed Ethernet function. Supports IEEE 802.1Q VLAN
and port-based VLAN. We can access and manage the device via web browser, including IP configuration, port
configuration, VLAN configuration, PoE configuration, factory reset, etc. We can also view device information,
such as switch status, port status, PoE status, etc. In addition, the PoE port enables remote control of the
device' on/off.
Equipped detecting chip inside which will make the PoE identification handshake with IEEE802.3af/at/bt PDs.
Such as PTZ cameras, wireless APs, base stations, and other PoE-powered devices which need high power
watts. Protecting non-PoE powered devices. Each PoE output port delivers 1.75A up to 90W(max) power for
remote PDs over 4 pairs.
One fiber slot only supports 1000Mbps of optical module, while RJ45 copper port supports 10/100/1000Mbps.
Enclosed in an IP40 high-impact metal case with a DIN Rail mount bracket, designed for indoor use but can
work outdoors by covering it with a waterproof case. It works with an input voltage of 48-57Vdc and operates
under -40°C to +65°C. For planning purposes, the effective distance is 100 meters over Cat5/5e/6 cables.
󾋸
󾋹
󾋺
1．Ｄａｔａ Ｉｎｄｉｃａｔｏｒ
2．ＰｏＥ Ｌｏａｄ Ｉｎｄｉｃａｔｏｒ
3．ＳＦＰ Ｉｎｐｕｔ Ｐｏｒｔ
4.ＳＦＰ Ｉｎｄｉｃａｔｏｒ
5.ＤＣ Ｐｏｗｅｒ Ｉｎｄｉｃａｔｏｒ
6.．ＰｏＥ Output Port
7.ＤＣ Input port
8.ＤＩＮ Rail Bracket
9.GND Terminal
󾋽
󾋾
󾋿
󾌀
󾋻
󾋼
󾋸󾋻󾋻󾋼
󾌀󾋼󾋷 󾋺󾋼󾋻
１ Ｐｒｏｄｕｃｔ Ｄｉａｇｒａｍ ２ Ｄｉｍｅｎｓｉｏｎ
This document belongs to PROCET company. It is not allowed
to reproduce and modify without the original author'
spermission. It is PROCET's policy to improve its products as
new technology components, software , and firmware at any
time. PROCET, therefore, reserves the right to change
specifications without prior notice.
Please follow WEEE (Waste Electrical and Electronic Equipment)
disposal instructions for old electronicproducts. Please do not
dispose of the old product in your general household waste bin.
The symbol indicates that the product should not be
discarded as unsorted waste but must be sent to separate
collection facilities for recovery.
Copyright ©2023 Creative Lianjie Network
Technology Co.Ltd All rights reserved.

Ｓｐｅｃｉｆｉｃａｔｉｏｎ
Ｔｒｏｕｂｌｅｓｈｏｏｔｉｎｇ Ｃａｕｔｉｏｎ
       
www.procetpoe.com
Ｉｎｐｕｔ
ＰｏＥ Ｓｔａｎｄａｒｄ
Ｃｌａｓｓ Ｌｅｖｅｌ
ＰｏＥ Ｐｏｗｅｒ Ｐｉｎｓ
Ｗｏｒｋ Ｔｅｍｐ．
48-57Ｖｄｃ 7.5Ａ
ＩＥＥＥ802.3 ａｆ ／ ａｔ ／ ｂｔ
Ｃｌａｓｓ 8
－40℃ ｔｏ 65℃
Ｎｅｔｗｏｒｋ Ｐｏｒｔｏｃｏｌ
ＲＪ45：10／100／1000Ｍｂｐｓ ＳＦＰ：1Ｇ
Ｄａｔａ Ｓｐｅｅｄ ＩＥＥＥ802.3ｉ /IEEE802.3u /IEEE802.3ab/IEEE802.3z
4／5（＋），7／8（－） ＆ 3／6（＋），1／2(－）
Ｏｕｔｐｕｔ
ＰＴ－ＰＩＳ4ＰＢ1Ｓ－Ｍ
Ｄｉｍｅｎｓｉｏｎｓ & NW
ＥＭＣ ＥＮ55032：2015／Ａ11：2020
Ｃａｕｓｅ Ａｎａｌｙｓｉｓ
ＥＮ55035：2017／Ａ11：
46－57Ｖｄｃ 1750ｍＡ,Each port：90Ｗ（Ｍａｘ ）
2020
144.5ｍｍ Ｘ 95ｍｍ Ｘ 35.4ｍｍ 483ｇ
Failure
Model
Phenomena Solutions
Power LED
Light off
Poor Power outlet
Poor Power cord
Power cable is not plugged in
Not plugged in / no power Plug in the power cord
firmly
Check if the socket connection
is loose, if the AC cable is
damaged, or if the power
supply is abnormal.
Load
Indicator
Device issues Device replacement
Light Off
Poor network cable contact or
network cable failure.
Non-PoE compliant PD or
unsupported PD or
Re-plug the network cable
or replace the network
cable.
mismatched PD PD replacement
PD Damage
Data
Transmission
PD replacement
Abnormality
Shorten the connection
distance, or add an extender/
Check if the total length of the
network connection cable exceeds
100 meters. repeater.
SFP port signal source malfunction Check if the switch working
properly.
Check if the cable comply with
the EIA/TIA568B or 568A.
Change good network cable if
Ethernet data transmission failure
the previous cable is poor.
1. Please read the instructions carefully and follow the
standard operating procedures before using.
2. Please place it in a well-ventilated and dry area, and it is
for indoor use only.
3. Connect the DC power cable with positive and negative
wires into the DC terminal block of Procet Injector.
at least 5cm of clearance on all sides of the device for
4. Connect a fiber cable with SFP optical module at 1G
from your switch into the injector's SFP slot for data Input.
(The optical module does not include in the package). You
can choose either single-mode or multi-mode SFP
transceivers.
5. Connect a CAT6 cable with the RJ45 connector into the
RJ45 socket labeled PoE. On the other end of the CAT6
cable, connect to your PoE Device (such as IP Cameras
etc). The total Ethernet cable length can not exceed 100
meters.
6. The device must be placed on a stable surface,
preferably affixed and mounted permanently. Do not leave
it "dangling" and use plugged-in cables in tension as
support. Drops, falls, and impacts experienced by the
injector can compromise the internal components & cause
premature failure.
7. Do not place heavy objects on top of this injector. Allow
heat ventilation / natural convection.