ProCurve J8454A User manual

61195868L1-13B, April 2005 www.procurve.com Copyright 2005 Hewlett-Packard Development Company, LP
Quick Start Guide 5990-8864
ProCurve Secure Router dl 1xE1 Module
J8454A
SPECIFICATIONS
Operating Modes E1/FE1 Frame Relay, E1/FE1 PPP
E1/FE1 Interface Line Rate: 2.048 Mbps ±50 PPM
Line Code: AMI or HDB3
Framing: FAS with optional CRC-4
Receiver Sensitivity: -30 dB
FE1 Line Rate: Channelized timeslot (in multiples of
56/64 kbps)
Connector: RJ-48C
Clock Source Network, internal
Diagnostics Test Pattern Generation and Detection: QRSS, 511,
all ones, all zeros
Network loopbacks
Alarm generation and detection
Network performance data (15 minutes and 24 hours)
Standards FCC Part 15 Class A, EN 55022 Class A, EN 55024,
EN 61000-3-2, EN 61000-3-3
ACIF S016, ETSI TBR 12/TBR 13
EN 60950, IEC 60950, AS/NZS 60950
ITU G.703, ITU-T G.704 (CRC-4), ITU-T G.823,
ITU-T G.797
Physical Dimensions: 6.99 cm (2.75 in) W x 10.80 cm (4.25 in) D
Operating Temperature: 0°C to 50°C (32°F to 122°F)
Relative Humidity: Up to 95 percent, noncondensing at
30°C (86°F)
Non-Operating Temperature: -20°C to 70°C (-4°F to
158°F)
Non-Operating Relative Humidity: Up to 95 percent,
noncondensing at 30°C (86°C)
Altitude: Up to 3.05 km (10,000 ft)
INSTALLATION INSTRUCTIONS
1. Remove power from the unit.
2. Slide the option module into the option slot until the module is
firmly seated against the chassis.
3. Secure the screws at both edges of the module.
4. Connect the cables to the associated device(s).
5. Complete the installation of the base unit.
6. Restore power to the unit.
Note For safety information for the routers and all
modules, please refer to the safety and ESD
precautions in the ProCurve Secure Router
Installation Guide included in your router shipment.
E1 NETWORK (RJ-48C) CONNECTION PINOUT
Pin Name Description
1 R1 Receive data from the network
2 T1 Receive data from the network
3 — Unused
4 R Transmit data toward the network
5 T Transmit data toward the network
6-8 — Unused
Note An optional backup module is required for backup
applications.
For a description of the backup connection pinouts,
refer to the Quick Start Guide included with your
backup module

61195868L1-13B, April 2005 Printed in the USA Copyright 2005 Hewlett-Packard Development Company, LP
Quick Start Guide 5990-8864
ProCurve Secure Router dl 1xE1 Module
J8454A
1XE1 MODULE COMMANDS
clock source [line* | internal]
Configures the source timing used for the interface.
line* Recovers clock from the primary circuit.
internal Provides clocking using the internal oscillator.
coding [ami | hdb3*]
Configures the line coding for the E1 physical interface. The settings must match the
line coding supplied on the circuit by the service provider.
ami Specifies Alternate Mark Inversion.
hdb3*Specifies High Density Bipolar 3.
description <text>
Comment line to provide an identifier for this interface (for example, circuit ID, contact
information, etc.).
<text> Shows up to 80 alphanumeric characters.
framing [crc4]
Configures the framing format of the E1 interface. This setting must match the framing
format provided by the service provider.
crc4 Enables CRC-4 framing.
loop-alarm-detect
Enables detection of loop alarms on the E1 interface. Use the no form of this command
to disable loop alarm detection. This setting is enabled by default.
loopback network [line | payload]
Initiates a loopback on the interface toward the network. Deactivate using the no
loopback network command.
line Initiates a metallic loopback of the physical E1 network
interface.
payload Initiates a loopback of the E1 framer (CSU portion) of the E1
network interface.
loopback remote v54
Initiates an E1 remote loopback test (with a V54 loopback pattern). Deactivate using
the no loopback remote v54 command.
remote-alarm [rai* | ais]
Selects the alarm signaling type to be sent when a loss of frame is detected on the E1
receive signal.
rai* Specifies Remote Alarm Indication.
ais Specifies Alarm Indication Signal.
remote-loopback
Enables acceptance of remote loopback requests on this E1 interface. Deny
acceptance using the no remote-loopback command. This setting is enabled by
default.
sa4tx-bit [0 | 1*]
Assigns a value to the Tx spare bit in position 4.
show test-pattern
Shows the current test pattern error count.
shutdown
Turns off the interface. By default, all interfaces are disabled. Use the no shutdown
command to enable the interface and allow it to pass data.
snmp trap link-status
Enables the interface to send SNMP traps when there is an interface status change
and controls the SNMP variable, ifLinkUpDownTrapEnable.
tdm-group <group#> timeslots <DS0 range> speed [56 | 64]
Creates a group of contiguous DS0s on this interface to be used during the bind
process.
<group#> Number label (1 to 1024) to identify this TDM group.
<DS0 range> DS0s in this group in the form: <starting DS0 - ending DS0>.
56 | 64* (Optional) Specifies a channel rate of 56 kbps or 64 kbps.
test-pattern [clear | insert | ones | p511 | qrss | zeros]
Initiates sending the specified test pattern.
clear Clears the test pattern error count.
insert Inserts an error into currently active test pattern.
ones Generates continuous ones.
p511 Generates repeating pattern of ones and zeros.
qrss Generates a random pattern.
zeros Generates continuous zeros.
ts16
Enables timeslot 16 multiframe to be checked on the receive signal.
* Indicates default values.
Note This command list is an illustration of available
commands. For complete command descriptions and
default values, refer to the SROS Command Line
Interface Reference Guide provided on your ProCurve
SROS Documentation CD.