Production Basics RTW Table 3000 User manual

Production Basics, Inc. Massachusetts, USA 800.318.2770 617.926.8100 Fax: [phone] www.pbasics.com
ASSEMBLY MANUAL
Open the cartons and identify the left and right Frame1.
Legs and RTW Support Rail. Position Frame Legs so
that mounting holes for Uprights are at the back of the
RTW Table. Frame Legs have a horizontal open channel
that faces inward.
Screw the levelling feet all the way into the leg adjusters.2.
Slide leg adjusters into bottom of Frame Legs. Determine3.
desired table height and secure position by inserting two
(2) Basic Bolts. Adjust leveling feet if necessary.
Assembly Tips
Review entire instruction manual before proceeding.
•
Production Basics nameplate indicates front of frame.•
Legs are adjustable in 2-inch increments between 30-36 or 36-42•
inches high to customize worksurface height.
Don’t be a slave to gravity-recruit a co-worker to help you install and•
correctly position components and accessories.
References to ‘Left’ and ‘Right’ are oriented as if you were facing the
•
front of the workstation.
Need help? Call Assembly Support at 800.318.2770.
•
RTW TABLE
Item Numbers 3000-3115
Workstations
RTW Table with optional accessories
Basic Bolt
Wood Screw
Chrome Mounting
Plate
Mounting holes for Uprights
must be at back of Frame Leg.
RTW Support Rail
(channel faces inward)
Right Frame Leg
(channel faces inward)
PARTS AND HARDWARE QUANTITY
FrameLegs(leftandrightspecic) 2
Leg Adjusters 4
RTW Support Rail 2
Chrome Mounting Plate 4
Worksurface 1
Leveling Feet 4
Wood Screws 12
Basic Bolts 16
Allen Wrench 1
Other Items Needed (not included)
Phillips head drill or screwdriver
Rubber mallet
Level
Tape Measure
1303A301
1

Need Help? Call Assembly Support at 800.318.2770
Insert two (2) Basic Bolts into adjustable leg, determining1.
height. Screw in Leveling Foot
Insert four (4) wood screws through connection plate2.
and into the underside of the worksurface on the existing
RTW Table. Repeat for other connection plate on
opposite RTW Table.
Place the corner laminate worksurface in between the3.
workstations. Secure with wood screws though the
connection plate.
Use wood screws to attach adjustable leg to underside of4.
worksurface 1” from edge.
Note: Add-on Corner requires two (2) RTW Tables•
for proper assembly. Assemble RTW Tables
before assembling Add-on Corner.
PARTS AND HARDWARE QUANTITY
Height Adjustable Leg (2 pieces) 1
Leveling Feet 1
Connection Plates 2
Laminate Worksurface 1
Basic Bolts 2
Wood Screws 20
Allen Wrench 1
Other Items Needed (not included)
Phillips head drill or screwdriver
RTW ADD-ON CORNER
Item Numbers 3418-3519
Chrome Mounting Plate
Left Back
Mounting holes for Uprights
must be at back of Frame Leg.
RTW Support Rail
Connection Plate
Locate Support Rail. Loosely attach the Chrome4.
Mounting Plate to the outside of the Support Rail with
two (2) Basic Bolts using Allen wrench provided.
Slip the Chrome Mounting Plate into the slot on the5.
frame leg as shown. The leg will be between the Chrome
Mounting Plate and the Support Rail. Repeat for all sides
and tighten bolts.
Invert the assembled RTW frame onto the underside of6.
the worksurface. Position the worksurface and frame so
thatitisushwiththebackofunitwithequaloverhang,
left and right.
Attach the worksurface to the frame by drilling wood7.
screws through the pre-drilled holes in the Support Rails
and Frame Legs, then into underside of worksurface.
Turn RTW Table right side up.
1303A301
2