PROformance Hoops PROclassic 60 Operating instructions

ADJUSTABLE HEIGHT
GOAL SYSTEM
PROclassic 60

2
Thank you and congratulations for purchasing a Proformance Hoops Goal -
the finest basketball goal system on the market today! You will discover that
Proformance Hoops is unsurpassed in product innovation, quality and integrity in the
basketball equipment industry. We are focused on designing, engineering and
products that meet and exceed expectations of today’s toughest playing
environments and demanding players.
Consider the following to determine where to install the basketball goal:
Whether the goal is to be installed into a landscaped area next to the
playing surface or into a hard-surfaced area.
Backboard size and its extension distance from the structures.
If court markings are to be used.
Amount of playing surface desired beneath the goal.
Other functions of playing surface (such as driveway, tennis court, etc.)

3
Consult Proformance Hoops if you do not

PARTS LIST
4
IT EM QTY DESCR IPTION
A1MainPost
B1Actuator
C 1
Actuator plastic pipe
D
2
E 1 Lower Extension Arm
F 2 Upper Extension Arm
G 1 Backboard
H 1 Rim Height Sticker
J1
K 1 Flex Rim (Separate pack)
U1 1 Anchor Template
U2 4 16mm A nc hor J-b ol ts
U3 8 Thick washer for J-bolts
U4 12 Hex nut M16
U5 4 Anchor Rebar 36"L
U6 4 Lock Washer M16
R1 4
Carriage Bolt M10x45mm
R2 4 Washer M10
R3 4 Flange nut M10
HARDWARE LIST
13
Hex Bolt M12x270mm
2 1
3
1Hex Bolt M12x110mm
4
2Hex Bolt M12x40mm
5
4Hex Bolt M12x30mm
6
11 Lock Nut M12
7
22Flat Washer forM12 Bolt
8
26 Nylon Washer for M12 Bolt
UNDERGROUND PARTS
PARTS LIST
RIM HARDWARE
G
K
R1
R3
R2
A
B
H
C
E
F
F
U4
U6
U3
U3 U1
U4
U4
U2
U5
D
D
3
7
7
7
7
7
7
7
7
7
7
7
7
7
7
4
7
8
8
8
8
8
8
8
8
1
6
6
2
8
8
86
1
8
6
1
8
6
J
8
5
8
6
Mounting plate
Actuator attach sleeve
Hex Bolt M12x235mm

! !
WARNING
A hammer or mallet may be needed during assembly.
Figure1
Figure 3 Figure 4
Figure2
U6
U4
U3
U4assembled
U1
U2
A
U3
Playing
Court
Front side
Back
side
Place the Pole on the Anchor system.
Slide one Thick washer M16 (U3) over
each J-bolt (U2). Lift the Pole (A) onto
Anchor system, secure with one thick
washer (U3), one Lock washer M16 (U6)
and one Hex nut (U4) for each J-bolt.
See Figure 1.
If the Main Post (A) is not exactly
vertical, adjust the 16mm J-Bolt Hex
Nuts (U4) located under the Post base
(A). Tighten all of the Hex Nuts (U4)
Above Post base when Main Post (A) is
vertical.
NOTE: Face the Main Post (A) with Actuator
Bracket facing away from playing court (as
shown in ).FIGURE 2
1.
Attach Lower Extension arm (E) to
Pole (A), Figure 3as shown in .
Secure it with one Hex bolt M12x270
(#1), two Flat washers M12 (#7),four
Plastic Washers M12 (#8), one Lock
nut M12 6 See(# ). Figure 7.
Note make sure Plastic washers go:
between Lower Extension and Pole.
2.
A
Slide Plastic sleeve
over Actuator
5
1
78
8
E
6
7
8
1
8
8
8
7
76
J
5
5
7
7
7
8
8
3D
88
6