ProVisual BA401-SP User manual
Board Diagram
Please take the following steps
Please check the following accessory, if you find the item lost, please contact our local
dealer.
POE Splitter 1set
M to M DC power cable 1set
User
Manual
1set
1) Please turn off the system's power before the installation；
2) Connect network cable with PoE Switch and connect the other cable end with the Poe IN
port;
3) Connect the IP camera to POE splitter’s ethernet port with another cable;
4) Connect Splitter's DC port with the IP camera’s Power port with the DC cable.
5) Please examine the system and power it;
Installation
The product is a PoE Network and Power Splitter based on . The device is
compatible with POE switch that based on IEEE 802.3af standard. The product can also
provide network and power source for network device that does not support PoE function.The
product provide DC 5V/12V/24V 3 Level Power output. It can support different power request
for IP camera or IP device.。
IEEE 802.3af
Feature
PoE Splitter
Voltage Output: DIP Adjustment Available, available for various ethernet
product. Support 10/100/1000 Mbps data conversion.
Power Output：≤15.4W;
Transmission Medium：Cat5/5e/
Standard: Support IEEE802.3af Standard; Power supply support A（End-Span）and
mode B（Mid-Span）
Protection: Excellent circuit protection, strong lighting protection and anti-interference.
DC5V/12V/24V
6 Cable;
；
PoE Splitter
12
Cat5/5e/6 NetworkCable
Monitor
NVR
IP PTZ Camera
IP Camera
IP Dome Camera
Front
Back
Notice
To make sure the transmission quality, please use standard Cat5/5e/6 cable.
POE Switch
Application
POE Splitter
IP Camera
Ether ne t
PWR
DC
123
456
Ethernet
2PWR DC Power Out put LED，On: Power outp ut
Off: Power not o utput
3DC DC Power output port
4
5V/12V/24V
DIP Sw it ch, DIP level c ontrol diff er ent DC power ou tp ut,
5V/12V/24V power output available
5PWR PoE Power In put LED, On: PoE power i nput
Off: PoE power n ot input
6PoE IN PoE Ethernet Input Port
Ethernet
Ethernet
Ethernet
Ethernet
DC Power
DC Power
DC Power
DC Power
5V
PWR
12V
24V PoE IN
连接接 口
Specification 连接接 口
Item Description
Power
Power
Electric
Supply
Power
Voltage
AC100V~AC240V
Output
Power
Rate
≤15.4W
Network
Port
Communication
Port
1×RJ45 Input
TransmissionRate
10/100Mbps、10/100/1000Mbps
Transmission
Cat5/5e/6 Cable
Distance
100m（Max）
Status Power
LED
1（
Green
）
PoE LED
1 （Yellow）
Protection
Surge
Protection
1KV Per：IEC61000-4-5
ESD
1a
Contact
Discharge
L
evel
3
1b Air
Discharge
L
evel
3
Environmen
t
Working Temperature
0℃~55℃
Storage Temperature
-20℃~70℃
Humidity
0~90%
Structure
Size
120mm×62mm×39mm
Material
ABS
Material
Color Black
Weight
200g
Stability MTBF
>30000
h
连接接 口
Problem Examination
Please remove the problem according to the following steps
If the device installed according to the user manual；
If the RJ45 reach the standard of EIA/TIA568A or 568B;
Please make sure the POE port power rate output does not surpass 15.4W. Also please make
sure the input network device power rate does not surpass 15.4W.
Please use a normal device to replace the failure one；
Specification change will not be noticed
34
Instruments to be used: wire crimper, network tester. Wire sequence of RJ45 plug should
conform with EIA/TIA568A or 568B.
1. Please remove 2cm long the insulating layer, and bar the 4 pairs UTP cable;
2. Separate the 4 pairs UTP cable and straighten them;
3. Line up the 8 pieces of cables per EIA/TIA 568A or 568B.
4. Cut off the cables to leave 1.5cm bare wire;
5. Plug 8 cables into RJ45 plug, make sure each cable is in each pin.
6. Use the wire crimper to crimp it;
7. Repeat above 5 steps to make the another end;
8. Using network tester to test the cable whether is working.
Plug Producing Method
pin
color
white/green
green
blue
white/orange
white/blue
white/brown
orange
brown
1
2
3
4
5
6
7
8
pin color
1
2
3
4
5
6
7
8
white/green
green
blue
white/orange
white/blue
white/brown
orange
brown
EIA/TIA 56 8A EIA/TIA 56 8B
When choose RJ-45 make sure if one e nd is EIA/TIA5 68A,the other end should also be EIA/TIA568A.
When choose RJ-45 make sure if one end is EIA/TIA568B,the other end should also be EIA/TIA568B.
Notice
POE Injector
POE Injector
To prevent re or shock hazards, do not expose unit
to water for an extended period of time.
There are uninsulated and dangerous voltages within the enclosure of this
product. These currents may be of sufcient magnitude to cause electric shock
or death to individuals.
To reduce the risk of electric shock, please do not remove the cover or back of
this product. Only a qualied technician should tamper with the interiors of this
item and it’s electrical components.
• Avoid using this product at extreme high or low temperatures.
For more information please review product specications.
• Never expose products to direct sunlight or other extreme
conditions, damages to your product could occur.
• Do not mount or place any products near a heater or radiator.
*Violation of any of these recommendations could result in ProVisual voiding this products warranty. Please
visit our website for all details regarding your warranty.
HIGH RISK OF ELECTROCUTION.
CAUTION:
BA401-SP |PoE Splitter Instruction Manual
Product Features
Plug Producing Methods
• Voltage Output:DC5V/12V/24V,10/100/1000Mbpsdataconversion
• Power Output:≤15.4W
• Standard:SupportsIEEE802.3af,PowersupplysupportA(end-span)
andmodeB(mid-span).
• Protection:Excellentcircuit,lightingandanti-interferenceprotection.
• Structure:Supportstabletinstallation.2setsofPoEpoweradapters
canbeconnectedwithaBayonet. 14
CongratulationsonpurchasingthisBA401-SPmodelPoEsplitter.Thisitemis
compatiblewillallPoEswitchesthatarebasedonIEEE802.3afstandards.This
splittercanalsoprovidedataandapowersourcefordevicesthatdonotsupport
PoEfunctions.TheBA401-SPprovides3levelsofpoweroutput,DC5V/12V/24V
providingdifferentpowerrequestsforIPdevices.
NOTE:Pleasereadthisinstructionalbookletcarefullytoensureproperuseofthe
product,aswellasreducetheriskofinjuryordeath.
1.Remove2cmoftheinsulatinglayerfromtheendofcable,andbartogetherthe4
pairsofUTPcables.
2.Separatethe4pairsofUTPcableandstraightenthem.
3.Lineupthe8cablesofEIA/TIA568Aor568B.
4.Stripeachcabletoreveal1.5cmofbarewire
5.Plug8cablesintoRJ45plug,makingsurethatallcablesmakecontactwithpins.
6.Useawirecrimpertocrimptheconnection.
7.Repeatsteps1-6tocreateconnectionsasneeded.
8.Useanetworkcabletestertoassurecableisworkingproperlybeforeinstallation.
Instruments needed:wirecrimper,networkcabletester.
Board Diagram
Please take the following steps
Please check the following accessory, if you find the item lost, please contact our local
dealer.
POE Splitter 1set
M to M DC power cable 1set
User Manual 1set
1) Please turn off the system's power before the installation；
2) Connect network cable with PoE Switch and connect the other cable end with the Poe IN
port;
3) Connect the IP camera to POE splitter’s ethernet port with another cable;
4) Connect Splitter's DC port with the IP camera’s Power port with the DC cable.
5) Please examine the system and power it;
Installation
The product is a PoE Network and Power Splitter based on . The device is
compatible with POE switch that based on IEEE 802.3af standard. The product can also
provide network and power source for network device that does not support PoE function.The
product provide DC 5V/12V/24V 3 Level Power output. It can support different power request
for IP camera or IP device.。
IEEE 802.3af
Feature
PoE Splitter
Voltage Output: DIP Adjustment Available, available for various ethernet
product. Support 10/100/1000 Mbps data conversion.
Power Output：≤15.4W;
Transmission Medium：Cat5/5e/
Standard: Support IEEE802.3af Standard; Power supply support A（End-Span）and
mode B（Mid-Span）
Protection: Excellent circuit protection, strong lighting protection and anti-interference.
DC5V/12V/24V
6 Cable;
；
PoE Splitter
12
Cat5/5e/6 NetworkCable
Monitor
NVR
IP PTZ Camera
IP Camera
IP Dome Camera
Front
Back
Notice
To make sure the transmission quality, please use standard Cat5/5e/6 cable.
POE Switch
Application
POE Splitter
IP Camera
Ethernet
PWR
DC
123
456
Ethernet
2PWR DC Power Output LED，On: Power output
Off: Power not output
3DC DC Power output port
45V/12V/24V DIP Switc h, DIP level contro l differen t DC power out put,
5V/12V/24V power output available
5PWR PoE Power Input LED, On: PoE power input
Off: PoE power not input
6PoE IN PoE Ethernet Input Port
Ethernet
Ethernet
Ethernet
Ethernet
DC Pow er
DC Pow er
DC Pow er
DC Power
5V
PWR
12V
24V PoE IN
32
Board Diagram Specications
Troubleshooting
Installation
Front
Back
No. Board Description
1Ethernet EthernetOutputPort
2PWR DCPowerOutputLED
3DC DCPowerOutputPort
45V/12V/24V DIPPowerLevelSelector
5PWR PoEPowerInputLED
6PoEIN PoEEthernetInputPort
ITEM Description
Power
Protocol IEEE803.2af
PowerSystem A(End-Span)andB(Mid-Span)
PowerRate ≤15.4W
InputPower PoE48V/15.4W
OutputVoltage DC5V/12V/24Vadjustable
OutputMaxCurrent 1.5A
Ethernet
CommunicationPort 1xRJ45Input
TransmissionRate 10/100Mbps,10/100/1000Mbps
Medium Cat5/5e/6Cable
Distance 100m(300ft.Max)
Protection
SurgeProtection 1KVper:1EC61000-4-5
ESD
1acontactdischargelevel3
1bairdischargelevel3
Per:1EC61000-4-2
Environment
WorkingTemp. 0°C~55°C
StorageTemp. -20°C~70°C
Humidity 0~95%
Structure
Dimensions 80x59x24mm
Weight 146g
Stability MTBF >30000h
1.Pleaseturnoffallpowertoyoursystembeforeinstallation.
2.ConnectnetworkcabletoyourPoEswitch,andtheotherendtothePoEporton
thesplitter.(#6indiagramabove)
3.Usinganothernetworkcable,connectyourIPdevicetothesplittersethernetport.
(#1inabovediagram)
4.ConnecttheprovidedDCcabletoyourIPdeviceandtheotherendofcabletothe
splittersDCport.(#3inabovediagram)
5.Examineallcableconnectionsandpoweronthesystem.
1.Pleasecheckthatallconnectionsaresecuredandinthecorrectlocationsaccording
tothisusermanual.
2.PleasemakesurethatthepowerrateoutputDOESNOTsurpass15.4W,Alsothat
theinputnetworkdeviceDOESNOTsurpass15.4W
3.DoublecheckthatcableconnectorsreachEiA/TIA568Aor568Bstandards.
4.Ifproblemspersist,pleasecontactwww.provisual.com
