Pullman Holt E1200 Installation guide

Save For Future Reference
Portable Tank Extractor
Model E1200
Operation & Care Instructions
This extractor is a high quality, precision made product. All parts used in the manufac-
turingofthisextractorhave passed rigid quality control standards prior to assembly,and
an "each unit" final inspection prior to packaging is your assurance of proper assembly.
This extractor was protectively packed to prevent possible damage in transit. Should
damage occur,please notify the transporting carrier immediately for loss and/or claim.
IMPORTANT SAFEGUARDS
Make sure the machine is plugged into an electrical outlet with the
same voltage as shown on the switch plate of the machine. It is
important to have the machine properly energized.
Disconnect power cord from the outlet before attempting mainte-
nance or repair work. Do not leave machine connected to an elec-
trical outlet when unattended.
Do not operate machine in standing water. Such use can cause
electric shock.
Do not use volatile substances such as gasoline, kerosene, etc.in
the machine or anywhere near the cleaning area. The use or pres-
ence of such materials could cause an explosion and fire.
If an extension cord is necessary, use a three conductor grounded
cord, 12 gauge wire or heavier to prevent motor burnout and over-
heating of wire.
To avoid electric shock, do not expose to rain - store indoors.
Do not use the machine for dry vacuuming. The machine is not fit-
ted with a fine dust filter. To use machine for dry vacuuming,request
more information on a dry vacuum attachment.
Always use ball float filter (reusable vacuum filter) to protect vacuum
motors.
In case of overfoaming, use defoamer in recovery tank to prevent
damage to the vacuum motors.
Use only recommended carpet cleaning solutions and defoamer
intended for machines of this type. Do not use dyes, bleaches,
ammonia, or other additives. The use of powdered cleaning com-
pounds, if not diluted or dissolved properly may damage the pump.
Do not expose machine to freezing temperatures, it could be dam-
aged.
Only authorized repair shop or dealer should attempt repairs on any
machine.
Do not use unauthorized replacement parts. Proper performance of
the machine could be affected if substitutes are used.
WARNING
The machine is designed for use on carpet, floor and upholstery
extraction applications as per instruction and recommendations
written in this manual. Any deviation from its proper use or pur-
pose and the consequential damage that may occur is the sole
responsibility of the end user.

Use defoamer in recovery tank to prevent damage to vacuum
motors.
Make sure the drain valve and recovery tank lid are closed before
turning on vacuum and pump motor switches.
4. To clean,pull the wand over the carpet with solution control valve
lever pressed. Press solution control valve lever only during pull
strokes. (Fig. 6)
Release the solution control valve lever and pass the wand over
the dampened area once or twice with either a pull or push
stroke, or both. Repeat the process until the liquid does not
appear to be passing through the wand.
NOTE: The weight of the wand and the vacuum suction are suf-
ficient to obtain satisfactory results. Additional physical pressure
is unnecessary.
Continue cleaning until the clean water tank is empty and/or
recovery tank is full. Turn off all switches and empty the recov-
ery tank. The vacuum suction will be reduced if the recovery
tank is full.
5. After recovery tank is drained, repeat steps 3 & 4.
LAST STEP:
Turn off pump switch but leave the vacuum switch (s) on.
Disconnect the vacuum hose and solution hose from the wand.
Insertthe vacuumhose into the cleanwater tankand vacuum out the
excess water. (Fig.7) Drain and thoroughly clean the recovery tank.
Make sure the ball float cage and vacuum filter have been rinsed
thoroughly while it’s still wet.
Remove dirt and lint build-up inside the recovery tank, rinse with
running water. Make sure debris does not become lodged in
between the rubber gaskets on the drain valve.
Pump clean water through pump to protect unit from freezing.
Wrap power cord around cord-winder or handle.
Check for any loose parts on the machine, if loose, tighten them.
Never use solution tank as storage, machine can be damaged.
Operating Procedures
FIRST STEP:
Always thoroughly vacuum the surface to be steam-cleaned.
MACHINE ASSEMBLY:
1. Connect vacuum hose to vacuum intake (#1) on the machine and
to the wand (#3). Connect solution hose to the water output
(solution hose connector) (#2) on the machine (Fig. 1) and to the
quick connector on the wand (#4). (Fig. 2)
2. To reduce the possibility of electric shock,the machine is factory
equipped with an approved three conductor cord and grounding
plug. This plug is to be used only with proper grounding type
(three prong) receptacles. (Fig. 4)
An adapter is available for connecting three prong type plugs to
two prong receptacles. (Fig. 5) The green rigid lug extending
from the adapter must be connected to a permanent grounding
suchas properly grounded outlet box. Do not break off orpull out
the grounding blade.
OPERATION:
3. Method A
Pre-spray the carpet with carpet cleaning solution.
Fill open tank (solution tank) with clean hot water (140 F. max.)
(Fig.1) (exception: use cool water for wool carpets)
Method B
Fill open tank (solution tank) with clean hot water. Add 2 or 4
ounces of carpet cleaner per gallon of water or as needed.
IMPORTANT: Make sure ball float filter (vacuum filter) is clean
and in place at all times.
Use only recommended carpet cleaning solution intended for
machines of this type. Do not use solvents, bleaches, ammonia,
or other additives which can damage the machine and the car-
pet.

Symptom Possible Cause(s) Corrective Action
ELECTRICAL SYSTEM
No electrical power 1) Check the outlet & the plug 1) Plug in properly
2) Damaged cord 2) See authorized service center
3) Circuit breaker off or fuse blown 3) Turn circuit breaker on or replace fuse. Unplug any equipment using
the same circuit.
Switch is turned on, power 1) Faulty electrical cable 1) See authorized service center
is intermittent to all motors 2) Defective switch 2) See authorized service center
3) Loose terminal or corroded connector 3) See authorized service center
Electrical shock 1) Equipment not grounded 1) Check outlet for proper grounding. See authorized service center
VACUUM SYSTEM
Vacuum motor on,little or 1) Lid is not closed 1) Close the lid
no vacuum on suction 2) Drain valve not closed 2) Push drain valve handle down
head (wand) or upholstery 3) Hose or wand clogged 3) Clean
tool. 4) Accumulated dirt on the ball float cage 4) Clean or replace the filter
and filter
5) Worn out lid gasket 5) Replace the gasket
6) Lint and dirt build-up in wand 6) Clean the wand
7) Damaged vacuum hose 7) Replace
8) Loose or no vacuum hose connection 8) See authorized service center
inside the machine
9) Lint accumulation in vacuum fans 9) See authorized service center
Vacuum motor runs intermittently 1) See authorized service center
PUMP SYSTEM
Pump motor stopped 1) Pressure built up 1) Release pressure by opening up (press the lever on the wand)
2) Thermal overload (overheated) 2) Turn off the switch and wait for the pump to cool down.
3) Damaged motor or rectifier 3) See authorized service center
4) Pump switch defective 4) See authorized service center
5) Loose wire connection 5) See authorized service center
6) Pump pressure switch defective 6) See authorized service center
7) Faulty motor 7) See authorized service center
Loss of pump pressure 1) Clogged or dirty spray-tip 1) Clean
with wand valve open, 2) Accumulated dirt in solution line 2) Clean
and/or uneven or weak 3) Dirty or plugged filter screen 3) Remove and clean or replace
spray from the spray jet 4) Pump check valve worn or dirty 4) See authorized service center
tip 5) Malfunction in the wand valve 5) See authorized service center
6) Hose quick connect bad or clogged 6) See authorized service center
with lint
OTHER PROBLEMS
No water from the jet 1) Machine not plugged in (or circuit 1) Plug into proper sized outlet
breaker blown)
2) Switch is not on 2) Turn the switch on
3) Empty solution tank 3) Fill the solution tank with water
4) The hose (s) not connected properly 4) Connect hose (s) properly (see pump problem section)
Water or foam coming 1) Over foaming of water in recovery tank 1) Put defoamer in the recovery tank or put it in the vacuum hose with
out of the exhaust vac motor running
2) Elbow fitting in recovery tank pointing 2) Point the elbow away from ball-float cage
toward the ball-float cage
3) No ball-float cage 3) Install ball-float cage w/ filter
4) Too much water in the recovery tank 4) Drain the recovery tank
WARNING : Always disconnect power cable from electrical outlet when working on this machine.
DO NOT ATTEMPT TO REPAIR THE MACHINE. CONSULT AN AUTHORIZED PULLMAN-HOLT SERVICE CENTER.
TROUBLE SHOOTING GUIDE

10702 N 46th Street •Tampa, FL 33617
[phone] •toll free [phone]
fax [phone] •order entry fax [phone]
www.pullmanholtcorp. com B703603 1/04