Blaupunkt Bluebot Xtreme User manual

USER MANUAL
BLUEBOT XTREME
Product introduction 02 - 16
Installation robot 17 - 21
App installation 22 - 40
Instructions 41 - 51
Maintenance 52 - 63
Others 64 - 74

Parts & accessoriesRobot, sensors & assembly
PRODUCT INTRODUCTION

Bottom view Robot
Top view Robot
PRODUCT INTRODUCTION

Filter cover
Dustbin button
Wall sensor
LDS laser ranging sensor
Anti-collision sensor for radar
Anti-collision sensor
Infrared recharging sensor
PRODUCT INTRODUCTION

Filter cover
Dustbin button
Wall sensor
LDS laser ranging sensor
Anti-collision sensor for radar
Anti-collision sensor
Infrared recharging sensor
PRODUCT INTRODUCTION
Dustbin
Clean it regularly
Maintenance dustbin
1. Press the button and pull the dustbin out backwards.
2. Open, empty and clean the dustbin.
Maintenance lter
3. Remove the filter gauze, sponge, and HEPA.
4. Clean the removed filter gauze, sponge, and HEPA with
water if needed.
5. Shake off the water drops and dry the pieces naturally,
only use them after they have completely dried.
6. When dry, install them in the following sequence:
filter gauze - sponge -HEPA.
Filter gauze
Button
Filter cover
Sponge
HEPA

Filter cover
Dustbin button
Wall sensor
LDS laser ranging sensor
Anti-collision sensor for radar
Anti-collision sensor
Infrared recharging sensor
PRODUCT INTRODUCTION
Sensors
Clean it regularly
Maintenance
Clean the sensors with a dry, soft cloth, including:
1. The sensors along the sides of the robot.
2. Three anti-dropping sensors at the bottom of the robot.
3. Infrared avoidance sensor in the front of the robot.
4. Radar avoidance sensor on the top of the robot.
5. Electric shock protector and charging base shrapnel at the
bottom of the robot (please cut the power off during cleaning).
6. Signal transmission area of charging base.

Charging contact
points
Universal wheel
Side brush
Battery cover
Rolling brush
Rolling brush
cover
Anti-drop sensor
Driving wheel
PRODUCT INTRODUCTION

Charging contact
points
Universal wheel
Side brush
Battery cover
Rolling brush
Rolling brush
cover
Anti-drop sensor
Driving wheel
PRODUCT INTRODUCTION
Anti-drop sensor
Clean it regularly
Maintenance
Clean the sensors with a dry, soft cloth, include:
1. The sensors along the side of the robot.
2. Three anti-dropping sensors at the bottom of the robot.
3. Infrared avoidance sensor in the front of the robot.
4. Radar avoidance sensor on the top of the robot.
5. Electric shock protector and charging base shrapnel at the
bottom of the robot (please cut the power off during cleaning).
6. Signal transmission area of charging base.
Anti-drop sensor

Charging contact
points
Universal wheel
Side brush
Battery cover
Rolling brush
Rolling brush
cover
Anti-drop sensor
Driving wheel
PRODUCT INTRODUCTION
Side brush
• Clean it regularly
• Replace the side brush every 3-6 months to ensure the best cleaning result
Installation
Make the left side-brush (L) and the right-side brush (R) correspond
to L and R on the bottom casing, keep pressing L and R and the side
brushes. They are installed when you hear a “click” sound.
Maintenance
1. Turn the machine over and pull the side brush out and upwards.
2. Remove hair and dirt and reassemble the side brush.
3. Make the left-side brush (L) and the right-side brush (R)
correspond to L and R on the bottom casing, press L and R to
reinstall them.
L
(left side brush)
R
(right side brush)
R L
R
L

Charging contact
points
Universal wheel
Side brush
Battery cover
Rolling brush
Rolling brush
cover
Anti-drop sensor
Driving wheel
PRODUCT INTRODUCTION
Rolling brush
Clean it regularly
Maintenance
1. Turn the machine over and press simultaneously on both
clips of the cover of the brush to open the cover and take
out the rolling brush.
2. Remove dust outside and inside of the rolling brush using
a tiny brush and clean the rolling brush.
3. Reassemble the rolling brush and press the rolling brush
and the rolling brush cover tightly to completely close it
again.
Clip
Main brush