Pulsar PGD40iSCO User manual

Model#PGD40iSCO
4000 Watt Inverter Generator
OPERATOR’S MANUAL
Warning: The Engine Exhaust from this product contains chemicals known to
the State of California to cause cancer, birth defects or other reproductive harm.
[e-mail]
866-591-8921
STOP DO NOT RETURN TO STORE!
HAVE QUESTIONS OR NEED SERVICE?
FUEL SOURCECIRCUIT BREAKERINDICATOR LIGHTLOW IDLE
PARALLEL CONNECTION
TO AVOID DAMAGE, DO NOT CONNECT OR DISCONNECT PARALLEL CABLES WHILE THE UNIT IS RUNNING.
SELECTOR SWITCH
SELECTOR SWITCH
TO AVOID DAMAGE, DO NOT CONNECT
OR DISCONNECT PARALLEL CABLES
WHILE THE UNIT IS RUNNING.
PROTEIONAGAINRBON MONOXIDE
CO SENTRY
OFF

1
Table of Contents
Introduction Safety Warnings and Notices
Thank you for choosing Pulsar Products!
This manual provides instruction on how to operate and use your
generator safely and correctly; be sure to read and understand
this manual before using your generator. If you have ANY questions,
please phone [phone] M-F or [email protected]
BEFORE using your generator.
All details and images in this User's Manual are believed to be
accurate at the time of publication.
Pulsar Products reserves the right to make updates to this manual
at any time.
Please contact Pulsar Support at 866.591.8921 or
[email protected] for the latest updates.
This manual is a permanent part of the generator set. If the
generator is resold, kindly include this manual with the generator.
DANGER indicates an imminently hazardous situation which,
if not avoided, will result in death or serious injury.
WARNING indicates a potentially hazardous situation which,
if not avoided, could result in death or serious injury.
CAUTION indicates a potentially hazardous situation which,
if not avoided, may result in minor or moderate injury. It
may also be used to alert against unsafe practices.
Failure to follow the instruction may result in the damage
to your generator and other property.
Safety Warning.........................1
Safety Instructions......................2
Names of Components...................3
Control Panel ..........................4
Control Functions.......................5
Preparing Your Generator.................6
Starting up the Generator.................7
Shutting Down the Generator .............7
Using the Generator.....................7
Service and Maintenance................ 9
Storage and Transport .................11
Troubleshooting.......................12
Technical Parameters ..................13
Electrical Schematic ...................14
DANGER
WARNING
CAUTION
NOTICE

2
Safety Instructions
Before operating your generator, you must read and
understand the manual and familiarize yourself with the safe
operation practices.
NEVER use a generator indoors! Exhaust
and Carbon Monoxide can KILL YOU in
minutes.
Avoid running the generator in the rain or
very high, condensing humidity.
Never smoke or allow any heat source
near the generator while refueling it.
Always shut down the generator and allow
it to cool before refueling!
This is a portable generator, DO NOT
attempt to connect it to any mains panel.
Take care not to spill any gasoline and
wipe up any accidental spills at once.

FUEL SOURCECIRCUIT BREAKERINDICATOR LIGHTLOW IDLE
PARALLEL CONNECTION
TO AVOID DAMAGE, DO NOT CONNECT OR DISCONNECT PARALLEL CABLES WHILE THE UNIT IS RUNNING.
SELECTOR SWITCH
SELECTOR SWITCH
TO AVOID DAMAGE, DO NOT CONNECT
OR DISCONNECT PARALLEL CABLES
WHILE THE UNIT IS RUNNING.
PROTEIONAGAINRBONMONOXIDE
CO SENTRY
OFF
3
Names of Components
Before operating your generator, you must read and
understand the manual and familiarize yourself with the safe
operation practices.
Lifting Handle
Left Enclosure Control Panel
Recoil Start
Spark Plug Access
Rear Panel
Muffler
Fuel Tank Cap
Oil Fill Access
Air Filter Access
Right Enclosure

4
Control Panel
SELECTOR SWITCH
TO AVOID DAMAGE, DO NOT CONNECT
OR DISCONNECT PARALLEL CABLES
WHILE THE UNIT IS RUNNING.
PROTEION AGAIN RBON MONOXIDE
CO SENTRY
OFF

5
Control Functions
Selector Switch
OFF - Ignition circuit is off, the fuel valve is closed, the engine
will not run.
RUN – Ignition circuit is on, the fuel valve is open, the choke is
open, and the engine runs normally.
START (CHOKE) – (only used for cold starting) Ignition circuit is
on, fuel valve is open, choke is closed.
If the engine is hot, do not
use the choke.
Oil Indicator (Red)
When the engine oil level drops too low the engine will
automatically shut down and the oil alarm indicator illuminates.
The engine can be restarted up only after the engine oil is filled
correctly.
Tip: If the engine will not start turn the 3 in 1 knob to "RUN"
position and pull recoil handle. If the oil indicator flashes a few
seconds, the oil volume is insufficient, fill oil to the dipstick high
mark and restart it.
SELECTOR SWITCH
NOTICE
INDICATOR LIGHT
INDICATOR LIGHT
INDICATOR LIGHT
Overload Indicator (Red)
When the overload indicator illuminates, the generator has
detected excess electrical load and the circuit breaker may
open (trip).
If the overload indicator illuminates and the generator has no
electrical output, perform the following:
①Disconnect all electrical loads then and shut down the
generator.
②Reduce total draw of electrical loads connected, less than
rated output.
③Confirm there is no debris blocking the air inlet, correct as
necessary.
④Next, restart the engine and add electrical load in gradual steps.
Tip: When using electrical equipment with high starting current
(such as compressors, saws, pumps, etc.), the overload indicator
may illuminate for a few seconds, this is normal.
AC Indicator (Green)
The AC indicator illuminates when electrical output is stable.
Energy Saving (Idle) Switch
1) "ON"
When energy saving switch is switched to "ON" position engine
speed is reduced when the generator is under light load. This
feature will reduce fuel consumption and noise.
LOW IDLE

6
Control Functions Preparing Your Generator
2) "OFF"
When the energy saving switch is set to the "OFF" position, the
engine will run at rated speed, regardless of connected load.
Fuel Tank Cap
Remove fuel tank cap by unscrewing it counterclockwise.
AC Circuit Breaker
If the total AC load exceeds the rated current, the AC circuit
breaker will open (trip) and the button will pop out. In this case
disconnect all loads, restart the generator and push in the AC
circuit breaker(s).
Grounding Terminal
If grounding is required by code or application, follow the
guidelines on page 12.
Fuel
After fueling, wipe up any gasoline residue with a soft cloth to
prevent damage to the plastic enclosures.
Fuel tank capacity: 1 US gallon
Engine Oil
Your generator ships without engine oil. Do not attempt to start the
generator without sufficient engine oil in the crankcase.
1）Place your generator on a flat, stable surface.
2）Unscrew the knob ①to remove oil access cover ②
3）Unscrew oil dipstick ③.
CIRCUIT BREAKER
Gasoline is highly flammable and toxic. You must read and
understand ALL safety instructions before fueling your
generator.
Do not overfill the fuel tank! Heat and vibration can cause
fuel to leak from an over-filled fuel tank.
After refueling, confirm that the fuel tank cap has been
tightened.
Remove fuel tank cap and add gasoline to the red horizontal
line.
DANGER
NOTICE
Maximum Fuel Level

7
Preparing Your Generator
Starting The Generator
Shutting Down the Generator
Using the Generator
4）Use a funnel to add 12 fluid ounces (0.35L) of 10w-30
engine oil to the crankcase, verify oil level with the dipstick.
5）Reassemble oil access cover and tighten the knob.
Pre-use inspection
Fuel
Check fuel level; add if necessary.
Oil
Check oil level; add if necessary.
Check for any oil leaks.
1）Disconnect all electrical loads.
2）Move Energy Saving (Low Idle) switch to "OFF".
3）Turn the 3 in 1 knob to "CHOKE"
Tip: When the engine is warm, choke is not necessary.
5）When starting the generator, grasp the handle firmly with
your free hand to stabilize the generator.
6）First gently pull the recoil rope until resistance is felt, then
let it retract, then pull it swiftly at once.
1）Turn the 3 in 1 knob to "OFF" position
Operating Range of the Generator
• Ambient air temperature: 23F–104F (-5 ~ 40°C)
• Relative humidity <95%
• Recommended elevation <5,000 feet (1,500m) reduced
power at >3,300 feet (1,000 m)
Ideal Atmospheric Conditions
• Ambient air temperature: 77F (25°C)
• Relative humidity: 30%
• Atmospheric pressure: 1,000 millibars
Standard Deration:
• Every 9°F (5°C) increase in ambient air temperature will
reduce generator output by about 2%
• Every 30% of increase in relative humidity of air will reduce
generator output by about 1.5%
• Every 1,000 feet, (300m) elevation increase will reduce
generator output by about 4.5%
Even when not in use the generator is potentially
hazardous. Follow the checklist below before starting the
generator. If any problems are found, do not use the
generator until it has been repaired by an authorized
Pulsar Products service center.
NOTICE
SELECTOR SWITCH
SELECTOR SWITCH

FUEL SOURCECIRCUIT BREAKERINDICATOR LIGHTLOW IDLE
PARALLEL CONNECTION
TOAVOID DAMAGE, DO NOT CONNECT OR DISCONNECT PARALLEL CABLES WHILE THE UNIT IS RUNNING.
SELECTOR SWITCH
SELECTOR SWITCH
TOAVOID DAMAGE, DO NOT CONNECT
ORDISCONNECT PARALLEL CABLES
WHILETHE UNIT IS RUNNING.
PROTEIONAGAINRBONMONOXIDE
CO SENTRY
OFF
8
Using the Generator
Connecting Loads to the Generator
①Start the engine
②Move Energy Saving switch to "OFF"
③Insert the plug(s) into AC outlet(s)
④Make sure that AC indicator is illuminated
⑤Switch on electrical equipment
Tip: If total load is less than half rated capacity, move the
Energy Saving Switch to ‘ON’. If the generator supplies power
to multiple devices plug-in those devices in from large to
small according to rated electrical load.
Generator grounding
Generator Grounding
If grounding is required by code or application, follow the
guidelines below. If you have ANY doubt, contact a licensed
electrician.
①Use grounding wire of minimum 12 gauge
②Connect one end of grounding wire to the grounding bolt on
the control panel.
③Connect the other end of the grounding wire to a suitable
ground point.
Range of Application
Before using the generator, please make sure that total load is
within rated load range of the generator, otherwise the generator
may be damaged.

9
Service and Maintenance
Good maintenance is essential for safe, economical operation and long service life. The maintenance schedule is below:
Maintenance Cycle
Item
Engine oil
√
Replace
√
√
√
Air Cleaner
Element
Inspection √
Clean √
Replace √
√
Clean √
Clean - Adjust √*
Clean √
Idle Speed
√
Check - Adjust
√
Clean
√
Fuel Hose Inspection Every Two Years
Remove
Carbon
Deposit **
Check - Fill
Check - Adjust
** These tasks should be completed by an authorized Pulsar service center.
Displacement <225cc, every 125 hours; displacement
≥225cc, every 250 hours.
Cylinder Head, Piston
Fuel Tank and Fuel
Filter **
Valve Clearance **
Spark Arrester
Spark Plug
Carburetor Float
Bowl
Each
Week
Break-In
Maintenance at
1 Month or
20 Hours Use
Quarterly
Maintenance is
every 90 Days or
50 Hours Use
Annual
Maintenance
or 100 Hours
Use

10
Service and Maintenance
Spark Plug
①Remove access cover and spark plug boot.
②Use the (included) thin-wall T-socket wrench to remove the
spark plug by turning it counter-clockwise.
③Inspect spark plug for discoloration and remove carbon
deposits; replace if necessary.
④Adjust the gap 0.7~0.8mm.
Spark Plug # A5RTC
Gap: 0.7-0.8mm
⑤Install new or serviced spark plug in reverse order.
Spark Plug torque: 12.5 Nm; 110 in lbs.
Tip: If no torque wrench is available turn the spark plug ¼ - ½ turn
after the gasket contacts the cylinder head.
Adjustment of the Carburetor
This carburetor is not adjustable, only maintenance and cleaning
are possible. We strongly recommend leaving this work to an
authorized Pulsar Service center.
Oil Change
1) Raise the generator up on support blocks on a flat, stable
surface
2）Unscrew the knob ①, to remove oil access cover
3）Unscrew oil dipstick ③
4）Place an oil pan under the engine, tilt the generator toward
the oil pan until all oil has drained; wipe up any spills.
6）Refill crankcase with 12 ounces (0.35l) 10w-30 engine oil; check
with dipstick.
7）Tighten oil dipstick, replace oil access cover, and tighten the
knob.
Air Filter
A dirty air filter can cause poor performance and engine damage.
Perform inspection and cleaning per the maintenance schedule
on page 9.
If the generator is used in high temperature or under high
load, change the oil every 25 hours.
If the generator is used in a dusty or abrasive environment,
service the air filter element every 10 hours; replace it
every 25 hours.
If you miss a maintenance cycle, perform the maintenance
as soon as possible per the table above.
Do not drain the oil immediately after turning off the generator;
allow it to cool completely before servicing it.
Shut down the engine and allow it to cool before performing
any service. Place the generator on a flat, stable surface.
Remove the spark plug boot to prevent accidental engine
start.
NEVER USE ANY GENERATOR INDOORS or in any poorly
ventilated area. Engine exhaust contains carbon monoxide
which can KILL you and others in the area.
NOTICE
DANGER
WARNING
①
③

11
Service and Maintenance
Storage and Transport
Spark Plug
1). Remove screws ③, to remove air filter housing ④;
2). Remove foam filter element ⑤;
3). Clean foam filter element with a mild soap solution, rinse
well and let it dry
4). Place a few drops of engine oil on the foam filter element
and squeeze gently to distribute the oil film evenly
5). Reinstall the air filter element in reverse order. 1. Remove fuel tank cap and fuel tank filter screen.
2. Clean fuel tank filter screen with mild soap and hot water.
3. Allow filter screen dry thoroughly and replace it in the fuel tank.
4. Replace fuel cap tightly.
Generator Long Term Storage
1). Turn the 3 in 1 switch to "OFF" and allow generator to cool
completely.
2). Remove the spark plug boot to prevent accidental engine
start.
3). With the engine completely cool, move the fuel cap vent
lever to ‘ON’
Fuel Filter Screen
①
②
⑤
③
④
NEVER approach the generator while smoking or with any ignition
source!
DANGER
SELECTOR SWITCH

12
Storage and Transport
Troubleshooting
4). Remove bolts and right service access panel
5). Using a Phillips screwdriver, open fuel drain valve on the
carburetor, and . drain remaining fuel into an approved
gasoline container.
6). Tighten fuel drain valve.
7). Change engine oil per page 9
8). Remove spark plug and instill one teaspoon (5ml) new engine
oil into combustion chamber. Pull the recoil a few times,
to distribute oil, then reinstall the spark plug.
9). Replace right service access panel.
10). Gently pull recoil handle until you feel resistance, indicating
the intake and exhaust valves are closed.
11). Store the generator in a clean and dry area.
Generator Transport
Pulsar Products recommends that the generator should be
empty of fuel when transported unless the generator is secured
in an open truck bed and secured from tipping. In this case,
follow the guidelines below:
• Do not completely fill the fuel tank, leave some expansion space.
• Do not run the generator while transporting.
• Protect from direct sunlight.
• Do not transport the generator across rough terrain.
Engine No-Start
Fuel System
1) There is no fuel.
2) Fuel doesn’t reach combustion chamber
3) Contaminated or old fuel
4) There is debris in the fuel valve
5) Carburetor is fouled, service carburetor
Insufficient Engine Oil
Oil level is too low
Ignition System
1) Verify 3 in 1 knob is at ‘RUN’ or CHOKE’
2) No spark from ignition coil failure.
3) Spark plug is fouled, service it per page 10
1) Worn out engine
2) Cylinder head bolts have loosened, have an authorized Pulsar
Service Center re-torque them properly
3) Head gasket leak
Engine Runs, No Power Output
1) Ensure all circuit breakers are pushed in
2) If generator was exposed to moisture or rain, move it to a dry
location for several hours
3) Vibration may have caused one or more connectors to loosen over
time, check with Pulsar Technical Support for guidance
4) Check electrical receptacles for damage
5) Generator may be overloaded. Remove load, shut down, then
restart the engine
Low Compression

13
Technical Parameters
Item Parameter
Engine
Engine Model 148F/P -2 164F/P
Engine Type
Bore size × Stroke (mm) 48.6×43
Displacement (cc) 79.7 145
Compression Ratio 8.7± 0.2 8.7± 0.2
Cylinder Head OHV OHV
Cooling Mode Forced Air Forced Air
Output Power (kW/r/min) 2.1/4500 3.8/4650
Starting Method Recoil
Fuel Tank Volume (L)
Fuel Type and Grade
Lubricating Oil Capacity
Lubricating Oil Model
Lubrication Mode Splash Lubrication Splash Lubrication
Noise dB (at 7m) 62 63
Generator
Rated Power (kW) 1.8 2.8
Rated Voltage (V) 120 120
Rated Frequency (Hz) 60 60
Rated Power Factor 1 1
Phase Number Single Phase Single Phase
Configuration
Motor Brushless (Permanent Magnet)
Voltage Regulation Inverter Regulation
Frequency Regulation Inverter regulation
Overall Dimension (mm) 18.9”x11.5”x17” 18.9”x11.5”x17”
Net Weight
Single-cylinder, four-stroke, air-cooled, overhead valve,
tilted 25º of the center of gasoline engine cylinder
64×45
1.1 Gallon (4L) 1 Gallon (3.7L)
Gasoline or Propane
12 Ounces (0.35L) 15 Ounces (0.45L)
SAE 10w-30 SAE 10w-30
40lbs. (18kg) 46lbs. (21kg)

14
Circuit Diagram
60Hz, 120V Electrical Schematic Diagram