Pulsar MOUSE 07 User manual

1
The exclusive distributor of AMC products
MOUSE 07
Dual Element Digital Motion Detector (dual
pyroelement + microwave)
CODE
MU07
In accordance with the
EN 50131-2-4 standard MANUAL EN
Edition: 2 from 07.03.2014
Supersedes: 1 from 10.02.2014
1. Introduction
The MOUSE 07 is a dual element digital motion detector with creep zone protection. With its
advanced signal processing algorithms and dual detection technology (PIR and MW) it is characterized by
very stable operation and low rate of false alarms.
Z Advanced digital temperature compensation enables operation over a wide temperature range. The
range of the MOUSE 07 detector is up to 14 meters with horizontal coverage exceeding 90 degrees. The area
of the sensor operation is shown in the Figure 5.
2. Installation of the detector
The detector should be mounted by a qualified installer, holding relevant permits and licenses (applicable
and required for a given country) for Intrusion Detection Systems.
The latch system used in the enclosure of the detector eliminates the need for screw connections, so that
the detector installation is simple and does not take much time.
Follow the basic rules for the installation of Intrusion Detection Systems (pay attention, among others, not
to soil or damage the pyroelement, do not point the detector towards strong light sources).
The optimum mounting height of the MOUSE 07 detector is 2 meters).
Fig. 1
Main view
Fig. 2
Inside view

2
Perform the following steps to mount the detector:
1. Open the detector by releasing (using thin screwdriver) the latch in the lower part of the enclosure (Fig.1).
2. Remove the PCB from the base by releasing the locking clip (Fig.2).
3. Make holes (for mounting the sensor on the wall) in the embossings at the rear or side of the housing. The
detector can also be mounted on the SN-1 rotating holder (not included).
4. Lead the cables through the hole located in the upper part of the enclosure (Fig. 2).
5. Connect the wires to the screw terminals and configure the detector
(Information on the distribution of terminals and control elements with a description of the available functions
can be found in the following pages).
6. Close the lid of the sensor.
CAUTION! When closing the cover of the detector, check whether the spring of the micro switch tamper is
correctly pressed into the tapered socket in the lid.
7. Connect the supply voltage and wait until the LED of the sensor stops flashing.
CAUTION! Leave the field of view of the detector.
The arrangement of the elements of the detector on the PCB is shown in the figure 3a and 3b.
Fig. 3a
Printed Circuit Board (front view)
Fig. 3b
Printed Circuit Board (rear view)
3. The detector configuration elements
The detector configuration uses the following elements mounted on the PCB:
 Potentiometer
 Five-position ON/OFF potentiometer
1. Potentiometer - adjusting the microwave range (MW)
To adjust the microwave range of the detector, use a potentiometer located on the PCB (Fig. 3a). The "+"
increases the range, and the "-" reduces the range of the detector.
The adjustment should be carried out in several steps. After the initial adjustment and closing the cover, check the area
of the sensor operation. Re-open the sensor housing and re-adjust the microwave range. Operating range of the MW
detector is adjusted with the DIP1 switch.
Caution! Detection sensitivity of microwave path should be adjusted to the size of the protected space.
Microwaves can penetrate gypsum walls, doors, etc., which may generate false alarms.

3
2. Five-position ON/OFF potentiometer
Set the dip switches in the correct position, depending on the features used. Pay attention to activate
the LED switch (walk test) - this will enable the proper configuration of the sensor (e.g. microwave
sensitivity). After configuring of the sensor, the LED can be turned off.
The designation and the switch
number
Function
L – H
Microwave range DIP1
The microwave detector range
ON – range of 7–15m
OFF – range of 3– 7m
OR DIP2 Unused switch
AUTO
OR AUTO function DIP3 ON –OR AUTO ON OFF –OR AUTO OFF
MEM
Alarm memory DIP4 ON – Alarm memory ON OFF – Alarm memory OFF
LED
Walk test DIP5 ON –LED ON OFF –LED OFF
 L-H (DIP1) – Adjusting the operating range of the MW detector
DIP1 – OFF low microwave range (3-7m)
DIP1– ON high microwave range (7-15m)
 „AUTO” (DIP3) –AUTO-OR function:
DIP3 – OFF The alarm is generated by both PIR and WM detectors or after six detections of the
microwave detector within less than 30 seconds.
DIP3 – ON – The alarm is generated by both PIR and WM detectors or after three detections of the
microwave detector within less than 30 seconds.
 „MEM” (DIP4) – Alarm memory.
DIP4 – ON This feature enables determining which detector triggered the alarm, which is indicated by
flashing LEDs (green LED – alarm by microwave detector, Orange LED – alarm by PIR detector, Red LED - –
alarm generated by both PIR and WM detectors).
This function is implemented by the „B/S” control input, which should be connected to the control panel,
while one of the control panel outputs should be programmed to supply the B/S terminal with the +13,8VDC
when the system is armed. When the system is disarmed, the B/S terminal shall be shorted to ground or
disconnected. In case of alarm, the LED will be signaling which detector triggered the alarm. The alarm memory is
reset each time the control panel is armed.
DIP4-OFF – turning off the alarm memory.
 „LED” (DIP5)- Walk test
DIP5 – ON – Walk test LED ON
DIP5 – OFF – Walk test LED OFF

4
4. Lens
Fig. 5a
Sensor range - side view
Fig. 5b
Sensor range - top view

5
5. Technical data
MOUSE 07
Power supply 9÷15VDC
Power consumption: Alarm / Standby 23,0mA /19,0mA@13,8VDC
Sensor range up to 14m
Operating angle 90°
PIR Sensor 2 components
Lens 29 areas in 5 levels
Microwave frequency 10,525GHz
Microwave power 10mW
Alarm signaling time 3s
Alarm type AND / OR AUTO
Tamper protection (opening of the detector) YES
Creep zone detection YES
Alarm memory YES
Maximum load of the contacts of the relay 100mA@40VDC /2,5-16Ω
Maximum load of the contacts of the tamper 40mA@30VDC
Operating temperature -10°C÷55°C
Storage Temperature -20°C÷60°C
Electromagnetic immunity
(radio frequency interference) RFI
30V/m (80MHz-2000MHz)*
LED (walk test) YES
In accordance to the standard EN 50131-2-4 Grade 2
Enclosure material ABS
Accessories Rotary handle (SN-1 version)**
Dimensions (H x W x D) 110 x 60 x 46mm
Resistance to animals NO
In accordance with the standards:
R&TTE 99/5/CE
EN 50131-2-4: 2008
EN 50131-2-4 Grade 2
EN 50131-2-4 Class 2
CEI 79-2: I° Level
RoHS
* Required RFI immunity: 10V/m
** The holder does not comply with the EN 50131-2-4 standard
Additional information
The manufacturer takes no responsibility for the defects that result from the damaging, malfunctioning or
inability to operate the equipment especially when resulting from failure to comply with the recommendations
and requirements contained in the manual.
It is necessary to periodically test the signaling device. The majority of Intrusion Detection Systems
indicates malfunctioning of the signaling devices and informs the user with an appropriate message on the
LCD keypad or LED light on the LED display. In case of such situation, the system installer shall be
immediately notified. Testing and control methods of Intrusion Detection Systems are specifically determined
by the installer.
The MOUSE 07 detector was made in accordance with the requirements of the EEC and 99/5/CE
directives. The Declaration of Conformity is available at www.pulsar.pl

6
WEEE LABEL
Waste electrical and electronic equipment must not be disposed of with normal
household waste. According to the European Union WEEE Directive, waste electrical
and electronic equipment should be disposed of separately from normal household
waste.
The exclusive distributor of AMC products:
Pulsar K. Bogusz Sp.j.
Siedlec 150, 32-744 Łapczyca, Poland
Phone [phone], Fax [phone]
E-mail: [e-mail], [e-mail]
www.pulsar.pl, www.zasilacze.pl
GENERAL WARRANTY CONDITIONS
1. Pulsar K. Bogusz Sp.j. (manufacturer) grants a two-year quality warranty for the equipment, starting from the production
date.
2. The warranty includes free-of-charge repair or replacement with an appropriate equivalent (selected by the manufacturer) if
the malfunction is due to the manufacturer. It includes manufacturing or material defects, provided that such defects have
been reported within the warranty period (point.1).
3. The equipment subjected to warranty should be brought to the place of purchase or directly to the main office of the
manufacturer.
4. The warranty applies to complete equipment, accompanied by a properly filled warranty claim with a description of the
defect.
5. Should the claim be accepted, the manufacturer is obliged to provide warranty repairs, at the earliest convenience,
however not later that within 14 days from the delivery to the service centre of the manufacturer.
6. The repair period mentioned in point 5 may be prolonged, if there are no technical possibilities to carry out the repairs, or if
the equipment has been conditionally accepted, due to the breaking warranty terms by the claimant.
7. All the services are carried out at the service centre of the manufacturer, exclusively.
8. The warranty does not cover the defects of the equipment, resulting from:
- reasons beyond the manufacturer's control,
- mechanical damage,
- improper storage and transport,
- use that violates the operation manual or equipment’s intended use
- fortuitous events, including lightning discharges, power failures, fire, flood, high temperatures and chemical agents,
- improper installation and configuration (failure to follow instruction).
9. The warranty is void in case of construction changes and repairs carried out by any unauthorized service center or in case
of damage or modifications to warranty stickers and serial numbers.
10. The liability of the manufacturer towards the buyer is limited to the value of the equipment determined according to the
wholesale prices suggested by the manufacturer on the day of purchase.
11. The manufacturer takes no responsibility for the defects that result from the damaging, malfunctioning or inability to
operate the equipment especially when resulting from failure to comply with the recommendations and requirements
contained in the manual.