Pulsarlube 1250RO-2 User manual

Kit No. 1250RO-2, 1250RO-3, 1250RO-4
NOTE : Oil brush and bracket assembly is sold separately (sold separately).
INSTALLATION INSTRUCTION
DETAILED PARTS AND ASSEMBLY PROCEDURE
www.pulsarlube.com
Multi-Point Remote Installation Kit for Pulsarlube OL
Rev.03
No.DescriptionPart No.
1250RO-4 1250RO-3
1250RO-2
Available Kits &ComponentParts
OL unit Sold Separately
1ea
1ea
1ea
-
-
-
-
-
-
1ea
9ea 11ea7ea
1ea
1ea
-
-
-
-
-
-
1ea
1ea
1ea
2ea 3ea 4ea
A002 Reducer, 3/8"F X 1/8"M Adaptor
Pulsarlube OL
Self Drilling Screw, #8 X 19
Distributor, 3(1P) M8 x 1P
Distributor, 4(2P) M8 x 1P
Distributor, 5(3P) M8 x 1P
Washer
1ea
Reducer, PT 1/8"F X M8 X 1P
Resistance Valve, #1 Distributor Spray
(one-touch type)
Distribution Tubing, O.D. 4mm x I.D. 2.5mm
Nylon Tubing, 20ft (6m)
Distribution Tubing, O.D. 4mm x I.D. 2.5mm
Nylon Tubing, 30ft (9m)
Distribution Tubing, O.D. 4mm x I.D. 2.5mm
Nylon Tubing, 40ft (12m)
Mounting Bracket, "L"Shape
B002
B051
C006
B057
C003-1
C003-2
C003-3
C004-1
4ea 6ea 8ea
Tube Clamp, Dia. 4mm x 1R
C010
2ea 3ea 4ea
Tube Fitting, Dia. 4mm x PT1/8"M
C007
2ea 3ea 4ea
Insert, Dia. 4mm x 2.5mmC011
2ea 3ea 4ea
Sleeve Ring, Dia. 4mmC009
4ea 6ea 8ea
Cable Tie
C021-2
C021-3
C021-4
B002
C006
C004-1
C021-2 C021-3 C021-4 C007C010 C011 C009
A002 B051
B057
C003-1 C003-2 C003-3
Cable Tie

1. Apply PTFE tape around the thread on reducer ( ) and
( ) on the tip of the lubricator.
2. Do not use PTFE tape on the reducer ( ) or the resistance
valve ( ).
1. Install the mounting bracket ( ) at a proper location using
screws ( ) to allow for easy installation and filling of oil.
2. Install the lubricator using the adaptor ( ), washer ( ),
and reducer ( ).
5. Assemble the reducer ( ) and the distributor ( , or ).
Reducer, PT 1/8"F X M8 X 1P
Distributor, 3(1P) M8 x 1P
Tube Clamp,
Dia. 4mm x 1R
Distributor, 5(3P) M8 x 1P
Resistance Valve, #1 Distributor Spray
Tube Fitting,
Dia. 4mm x PT1/8"M
Washer
Distribution Tubing,
O.D. 4mm x I.D. 2.5mm
Nylon Tubing 20ft (6m)
Ø4 X Ø2.5 Insert
Sleeve Ring, Dia. 4mm
Distribution Tubing,
O.D. 4mm x I.D. 2.5mm
Nylon Tubing 40ft (12m)
OL500 Unit
B057
C006
C003-1
C003-2
A002
B002
C021-2 C021-3
B051
C003-3
C009
C011
C004-1
C004-1
C004-1
C010
C007
C007 C007
Pulsarlube OL500
C021-4
11
C007
Kit No. 1250RO-2
Kit No. 1250RO-4
Kit No. 1250RO-3
C004-1
12
Reducer, 3/8"F X 1/8"M Adaptor
Mounting Bracket, "L"Shape
Self Drilling Screw, #8 X 19
Distributor,
4(2P) M8 x 1P
Distribution Tubing,
O.D. 4mm x I.D. 2.5mm
Nylon Tubing 30ft (9m)
Warning
For low viscosity oils below ISO VG 100, place the oiler below
the lube point and twist the lube line a couple of times to avoid oil
leaks caused by gravity.
INSTALLATION INSTRUCTION
DETAILED PARTS AND ASSEMBLY PROCEDURE
www.pulsarlube.com
Multi-Point Remote Installation Kit for Pulsarlube OL
Rev.03
ASSEMBLY PROCEDURE
3. Remove the oil reservoir lid and fill the cartridge with oil to
the 500ml level on the label. Turn the hand knob on the lid
counterclockwise 1~2 turns before closing the lid to open
the vent and relieve vacuum pressure.
4. Press the “TEST” button for 2 seconds to run test mode.
Confirm that the unit is dispensing oil properly.
6. Connect one end of the tubing to the resistance valve ( )
and the other end of the tubing to the fitting connector ( ).
Assemble the insert ( ) and sleeve ring ( ) in order, as
shown in the circled image on the left. If an oil brush and
bracket assembly is to be used, connect brush to a fitting
connector ( ) at the end of lube line using an appropriate
socket.
7. Use the tube clamps ( ) and screws ( ) to affix the tubing
( , or ) to a wall.
COMMENTS
xO
NOTE : All parts above are Metric thread.
3. Output volume may vary depending on oil viscosity, length of
lube line, ambient temperature, etc.
Kit No. 1250RO-2, 1250RO-3, 1250RO-4
11 12