Puretec WTV7210 User manual

For correct operation & installation it is essential to observe these instructions.
MAR2020
Installation Guide
Flow Meter
WTV7210

2Installation Setup Manual Copyright © Puretec Pty Ltd 2020
Introduction
Introduction
Thank you for purchasing a Puretec Flow Meter. Your Flow Meter is a proven performer
manufactured from only quality materials and components.
Suits 2CI valves only.
Installation
1. 
2. Install the meter on the OUTLET side of the valve, ensuring that the arrow on the

horizontal or vertical applications.
3. Connect the cable through the backplate of the control valve and into the 3 prong port
labelled 'METER'.
4. Program the valve (see Programming on page 3).
Thread cable through
the backplate.
Connect to "METER" port.

3
WTV7210 | Flow Meter
3. Preset to default. Press NEXT
to go to the next step.
4. Preset to default. Press NEXT
to go to the next step.
3. Preset to default. Press NEXT
to go to the next step.
4. Preset to default. Press NEXT
to go to the next step (step 8).
Programming
Programming
1. 
release.
Note: Press REGEN at anytime in the programming
sequence to return to the previous step.

required.
2. Preset to default. Press NEXT to go to the next step.
STEP 1F
STEP 2F
STEP 3F
STEP 4F
STEP 5F
STEP 6F
STEP 9F
STEP 8F
STEP 7F
STEP 10F
STEP 11F
STEP 3F
STEP 4F
STEP 5F
STEP 1F
STEP 2F
STEP 3F
STEP 4F
STEP 5F
STEP 6F
STEP 9F
STEP 8F
STEP 7F
STEP 10F
STEP 11F
STEP 3F
STEP 4F
STEP 5F
STEP 1F
STEP 2F
STEP 3F
STEP 4F
STEP 5F
STEP 6F
STEP 9F
STEP 8F
STEP 7F
STEP 10F
STEP 11F
STEP 3F
STEP 4F
STEP 5F
STEP 1F
STEP 2F
STEP 3F
STEP 4F
STEP 5F
STEP 6F
STEP 9F
STEP 8F
STEP 7F
STEP 10F
STEP 3F
STEP 4F
STEP 5F
Filter Soener (SOL)
STEP 1F
STEP 2F
STEP 3F
STEP 4F
STEP 5F
STEP 6F
STEP 3F
STEP 4F
STEP 5F
STEP 1F
STEP 2F
STEP 3F
STEP 4F
STEP 5F
STEP 6F
STEP 3F
STEP 4F
STEP 5F
STEP 1F
STEP 2F
STEP 3F
STEP 4F
STEP 5F
STEP 6F
STEP 3F
STEP 4F
STEP 5F
5. Preset to default. Press NEXT
to go to the next step.

4Installation Setup Manual Copyright © Puretec Pty Ltd 2020
Programming
STEP 8F
STEP 7F
STEP 5F
STEP 6F
STEP 5F
STEP 5F
STEP 6F
STEP 5F
6. Preset to default. Press NEXT
to go to the next step.
7. Preset to default. Press NEXT
to go to the next step.
 
• Auto: Capacity will automatically be calculated.
Note:
• oFF (default): Regeneration will be based solely on
the day override set; or
• A Number: 
).
Contact Puretec on (AU) 1300 140 140 (NZ) 0800

Press NEXT to go to the next step.
Soener (SOL)
Filter

5
WTV7210 | Flow Meter
 

• NORMAL: Means regeneration will occur at the
present time;
• on O : Means regeneration will occur immediately
when the volume capacity reaches 0 (zero); or
• NORMAL + 0: Means regeneration will occur at one

- The preset time when the volume capacity falls below



when the volume capacity reaches 0 (zero).
This step will not appear if step 8 is set to "oFF".
10. Preset to default. Press NEXT to go to the next step.
11. Preset to default. Press NEXT
to go to the next step (step
14).
11. Preset to default. Press NEXT
to go to the next step.
STEP 9F
STEP 8F
STEP 10F
STEP 11F
STEP 12F
STEP 13F
STEP 14F
RETURN TO NORMAL MODE
STEP 1F
STEP 2F
STEP 3F
STEP 4F
STEP 5F
STEP 6F
STEP 9F
STEP 8F
STEP 10F
STEP 11F
STEP 3F
STEP 4F
STEP 5F
Filter Soener (SOL)
Programming
STEP 9F
STEP 8F
STEP 10F
STEP 11F
RETURN
STEP 9F
STEP 8F
STEP 7F
STEP 10F
STEP 11F
RETURN

6Installation Setup Manual Copyright © Puretec Pty Ltd 2020
14. Preset to default. Press NEXT to go to the next step.
15. Preset to default. Press NEXT to go to the next step.
16. System is ready for use.
17. Test meter by opening a tap downstream, the word

indicate that the meter is detecting water usage.
STEP 12F
STEP 13F
STEP 14F
RETURN TO NORMAL MODE
STEP 12F
STEP 13F
STEP 14F
RETURN TO NORMAL MODE
STEP 12F
STEP 13F
12. Preset to default. Press NEXT
to go to the next step.
Soener (SOL)
STEP 11F
STEP 5F
STEP 6F
STEP 10F
STEP 11F
STEP 5F
13. Preset to default. Press NEXT
to go to the next step.
Filter
Programming

7
WTV7210 | Flow Meter
Exploded Diagram
Exploded Diagram
Typical meter retaining clip installation.
Ensure clip is fully engaged in groove
and tabs positioned in slot as shown.
Area of
detail
1
5
2
3
4
B Indicates BSPT
N Indicates NPT
Item Part no Description
1 - Turbine Assembly
2 - O-Ring
3 - Meter Housing MxF
Parts Identication
Typical meter retaining clip installation.
Ensure clip is fully engaged in groove
and tabs positioned in slot as shown.
Area of
detail
Item Part no Description
4 - Meter Retaining Clip
5 - Flow Meter Casing