PuriSystems HEPA 600 UVIG User manual

Do not use or install any parts to HEPA 600 UVIG that is not approved by PuriSystems.
Do not use the machine in a room or environment with explosive gases to avoid the risk of
explosion.
Do not plug the power cable into an unconnected ground socket. There is a risk of personal
injury.
Unauthorized alterations will invalidate the product warranty.
This machine is 110-120V rated. Plugging into an outlet with a different voltage rating may
cause equipment or property damage and serious personal injury.
A damaged power cord can be dangerous. There is a serious risk of damage and personal
injury if used.
Do not use the unit on standing water. If the electrical parts are damp/moist, let them dry before
use.
HEPA 600 UVIG is an air filtration system that uses high-graded filters, to expel particles from
the air such as mold spores, dust pollen, pet dandruff, etc. HEPA 600 UVIG is also suitable for
flood damage, fire repair, and it may also serve as woodcutting protection.
1.When the HEPA 600 UVIG is turned on, it will draw air from its location and pass it through a series of
filters. These filters are, Pre-filter, HEPA, and Activated carbon filter.
2.The first stage filter (Pre-filter) captures large particles.
The second stage filter (HEPA Filter) captures particles that are as small as 0.3 microns. They can be
smoke, dust, bacteria, pollen, and more.
The third and last stage filter is the Activated carbon filter. It absorbs dozens of harmful substances
such as formaldehyde, benzene series, ammonia, radon, TVOC, etc.
Using the auxillary outlet on the control panel, you can link up to 3 units together, creating a maximum
airflow 1800 CFM.You can also daisy-chain the machines when stacked vertically (limit of 2 units). Stackable up to 2 units.
Inspect the item upon arrival. If you find any damages, contact our customer support.
PLEASE READ THE SAFETY INSTRUCTIONS CAREFULLY BEFORE USE.
Daisy-Chain Capability. Up to 3 units.

2.Plug the unit into a 115v outlet. Each machine draws 3 amperes.
1.Place the unit in a vertical position.
3.The fan speed can be adjusted using the speed fan knob control.
Circuit breaker switch protection – When the maximum ampere allowed is exceeded, the circuit
breaker switch protector will activate to turn off the unit.
Speed fan knob control – To turn “on”, turn the knob clockwise until a “click” is heard. To reduce
fan speed, continue rotating the knob clockwise, and to increase the speed, rotate the knob
counterclockwise.
Warning. Harmful dust may spread during the process of replacing the filters. Propper PPE is
required. Gloves, eye protection, and mask.
Daisy Chaining – up to 3 HEPA 600 UVIG can be plugged into the machine’s GFCI outlet
(Maximum Ampere allowed is 12).
It is recommended to replace the pre-filter after every remediation job. If the ‘Change filter’ light
is on, replace the HEPA Filter.
Risk warning:harmful dust can spread when prefilters and composite filters are replaced.Therefore,users
should wear protective glasses, gloves and breathing masks that meet the FFP2 protection level.
Replacing the filter

Hour meter
Speed fan knob control
Overload Protection
switch
Change Filter light indicator for
HEPA FILTER
OFF/ON switch for UV and
ION Generator
GFCI Outlet

APPLICABLE SCENARIO
Odor Control
Other uses
CAUTION
Multiple units may be required to run at once during this application.
The HEPA 600 UVIG has been proven to be effective at filtering VOCs, smoke, soot, paint
smoke, and any other gases that may be causing bad odor.
HEPA 600 UVIG may also be used in many other applications such as, mold repair, fire
damage restoration, and dust removal.
Do not use the unit when the ‘Filter Change’ light is on.
Avoid the use of the unit near any equipment that may produce Carbon monoxide.
Do not pierce the filters.
Filters are not washable/cleanable. All filters must be replaced when necessary.
Proper alignment of the units is required when stacking. Do not stack more than two units.
Stacking guidelines
Water damage restoration

Fan won't start
Short Cycling
Device not powered on
Defective power cord
Defective switch
Damaged main control board
Poor air suction
The unit blows dust Filter is too dirty Replace the filter
Abnormal noise
Internal deformation
possibly caused by the
transportation
Contact customer support
for possible fan replacement
Don't pierce the filter. The puncture filter has the risk of dust diffusion.
The Primary filter and HEPA compound filters cannot be cleaned and must be replaced when dust
accumulates. (when the filter prompt light is on, the HEPA composite filter needs to be replaced,and
the timely replacement of the primary filter can improve the service life of the HEPA composite filter.)
When the primary filter screen and HEPA compound filter are replaced,the dust harmful to health will
be diffused. Therefore, users should wear protective glasses, gloves and breathing masks that meet
the FFP2 protection level.
In a humid environment, the service life of the HEPA composite filter will be reduced, and if it comes
into contact with water, it may be completely destroyed.
Use a different GFCI outlet
Check if the switch is on
Replace the main control board
Replace the fuse
Troubleshooting
Limited Warranty
This limited warranty is valid only on products purchased from the manufacturer or
Purisystems authorized dealer and operated, installed, and maintained according to the
instructions included in this user guide or furnished with the product. Purisystems will
not provide in-home service during or after the warranty period. You may be responsible
for the shipping charge to bring the product to the manufacturer for service.
This limited warranty starts from the date of purchase. Purisystems warrants to the
original purchaser that this Purisystems product is free from manufacturing defects in
material or workmanship for the limited warranty period of:
1 YEAR (FROM DATE OF PURCHASE): Purisystems warrants the unit’s parts will
operate free of defects in material or workmanship. This includes factory laborers. At its
discretion, Purisystems will replace defective parts, including factory labor. This does
not include transportation costs.
Possible Reason Solution
Problem

Limited Warranty Exclusions
Damaged caused by using next to combustible materials/equipment that may or may not produce
Damage caused by incorrect electrical line current, voltage, fluctuations, and surges.
Damaged caused by using in a high humidity environment (75% or higher).
Damage caused by failure to perform proper maintenance of the product.
This limited warranty covers manufacturing defects in materials or workmanship encountered in a normal
household, commercial or noncommercial use of this product and shall not cover the following:
Damage caused by unauthorized modification or alteration of the product.
Cosmetic damage including scratches, dents, chips, and other damage to the product’s finishes.
Damage caused by abuse, misuse, pest infestation, accident, fire, floods, or other acts of nature.
Damage occurs in uses for which this product was not intended for.
The use of this product in SPA or at a outdoor pool.
Damaged caused by not using the required filters for operation. (Pre-filter, HEPA & Activated Carbon
To receive warranty service, the purchaser must contact Purisystems via email at
[e-mail]. Proof of purchase or order number is required to receive warranty
service. During the applicable warranty period, a product will be repaired or replaced at the sole
option of Purisystems.
Filter)
carbon monoxide.