PXM DMX Repeater-IP User manual

PX097-IP
PX097-IP-K
DMX Repeater – IP
User manual

Table of Contents
1 Description...................................................................................................3
2 Safety conditions........................................................................................4
3 Connectors..................................................................................................5
4 Connection scheme...................................................................................6
5 Dimensions..................................................................................................7
6 Technical data.............................................................................................7
Manufacturer reserves the ri ht to make modi$cations in order to improve device
operation.
PXM Marek Żupnik sp.k.
Podłęże 654
32-003 Podłęże
BDO re ister number 000005972
tel. [phone]
mail: [email protected]
www.pxm.pl
Rev.1-1
16.01.2020
2

1 Description
DMX Repeater is a universal repeater and splitter of the DMX si nal.
The device allows to create rami$cations in the complex sta e DMX
installations and to amplify the DMX si nal, that means, enables to connect
next 32 receivers and to len then the DMX line. Accordin to the DMX
standard, the receivers in a DMX route must be connected in series. In the
PX097-IP-K version, all DMX lines have additional overvolta e protection.
In addition, in the last device a terminator must be installed. It is
impermissible to split the DMX line by simply “splittin the wire”. Because the
connection of receivers into one chain can be very troublesome in the case of
complex installations, the possibility of creatin DMX branchin and
amplifyin the control si nal is provided, which is what DMX Repeater – IP
provides.
With the PX097-IP repeater you can split the incomin DMX si nal into
two independent branches and amplify the DMX si nal. The device has an
optical isolation between input and two outputs. Obviously, connectin the
receivers to particular output routes must be performed accordin to the rule
of line in series, with the terminator installed in the last device.
The device casin is made of plastic and provides protection a ainst
adverse external factors.
3

2 Safety conditions
Repeater PX097-IP is a device powered directly from standard 230V AC
rid, what cause electric shock when safety rules are not observed. Therefore
it is necessary to observe the followin :
1. Repeater installation must be performed by a person holdin the
appropriate quali$cations, accordin to the manual.
2. All the conductors should be protected a ainst mechanical and
thermal dama e.
3. In the event of dama e to any of the wires, replace it with a cable with
the same technical parameters.
4. Only a shielded cable should be use to connect the DMX si nal.
5. Do not connect the device with a dama ed (cracked) housin .
6. All repairs and connection of the DMX si nal can only be carried out
with the power off.
7. All sudden shocks, particularly droppin , should be avoided.
8. Cleanin only with damp duster – PX097-IP has to be cut off the
power supply.
4

3 Connectors
5
Dmx Output1 Dmx Output2
Dmx Input
D+ D- GND D+ D- GND D+ D- GND
DMX input
DMX output
power supply
230V AC

4 Connection scheme
6
DMX controller
DMX Repeater
PX097-IP
DMX line
(max. 32 signal receiver, 300 m
DMX
IN
DMX
OUT
TERMINATOR

5 Dimensions
6 Technical data
type PX097-IP / PX097-IP-K
IP class 65
DMX I / O lines 1 / 2
DMX line connectors screw connectors (ter inal block)
isolation I / O breakdown voltage > 5000V
power supply 230V AC, 50Hz
power consu ption ax. 6,5W
housing aterial polycarbonate (PC)
weight 0.6kg
di ensions
width: 130
height: 180
depth: 76
7
76
130
180
max. 205
Remember about additional space
for cables coming out of the cable glands

Podłęże, 16.01.2020
DECLARATION OF CONFORMITY
PXM Marek Żupnik spółka komandytowa
Podłęże 654, 32-003 Podłęże
we declare that our product:
Product name: DMX Repeater – IP
Product code: PX097-IP / PX097-IP-K
meets the requirements of the followin standards, as well as harmonised
standards:
PN-EN IEC 63000:2019-01
PN-EN 60529:2003
PN-EN 61000-4-2:2011
PN-EN IEC 61000-6-1:2019-03
PN-EN 61000-6-3:2008
EN IEC 63000:2018
EN 60529:1991
EN 61000-4-2:2009
EN IEC 61000-6-1:2019
EN 61000-6-3:2007
and meets the essential requirements of the followin directives:
2011/65/UE DIRECTIVE OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 8 June 2011 on the
restriction of the use of certain hazardous substances in electrical and electronic equipment
Text with EEA relevance.
2014/30/UE DIRECTIVE OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 26 February 2014 on
the harmonisation of the laws of the Member States relatin to electroma netic compatibility (recast)
Text with EEA relevance.
2014/35/UE DIRECTIVE OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 26 February 2014 on
the harmonisation of the laws of the Member States relatin to the makin available on the market of electrical
equipment desi ned for use within certain volta e limits
m r inż. Marek Żupnik.
8