PYLE Audio PWMA220BM User manual

注意事项
CAUTION
FEATURES
1. Built-in bluetooth MP3 player.
2. Built-in one channel wireless microphone and one 6.35mm MIC in
socket to connect wired dynamic MIC. Two persons can speak or
sing at the same time.
3. One 3.5mm keyboard in socket to connect electronic device. And
one 3.5mm cassette in socket to connect cassette player or other
audio player.
4. One 3.5mm REC out socket can be connected to a recording device
or to the input jack of a power amplifier to further amplify and enlarge
the audio power.
5. Master power/volume control. Bass,Treble and Echo controls.
Suitable for karaoke.
6. Powered externally with AC, 12V DC or internally with built-in
12V/1.8A lithium battery or 6PCS UM1(D) batteries. Suitable for both
indoor and outdoor use.
7. Ideal for many applications, including use in classrooms,
conference/meeting rooms, churches, health clubs and small
auditoriums.
1. This unit is with speaker inside which can cause magnetic field. Keep
this unit at least 60cm away from computer or TV.
2. This unit is with built-in rechargeable battery. Please recharge the
battery every 2 months if you are not going to use the unit for a long
period of time. Or the battery may be damaged.
3. If the battery is damaged please replace with same specifications
battery. And dispose the damaged battery environment friendly.
4. Free from high temperature. Don't expose the device to the hot
equipment.
5. Don't place the device in the environment of humidity and dirts.
6. Place the device in the ventilated environment.
7. Don't pull the power cord while you pull out the plug. Hold the plug
tightly to pull it out.
8. Pull out the AC power if you will not use the device for a long time.
9. Your operation must be subjected to the specified voltage marked
near the AC in jack and complied with this guide.
SPECIFICATION
AMPLIFIER
TRANSMITTER
Power Supply
Frequency Response
Power Output
Mic Input
Echo Time
Speaker Impedance
Dimensions(WxDxH)
Weight
: AC~120V/60Hz
DC 12V
Built-in 12V/1.8A lithium battery
6PCS UM-1(D) batteries
: 25-15,000Hz
: 60W
: 1.4V rms, OVER 600ohm
: 120msec.
: 4 ohm
: 9.7'' x 5.2'' x 9.5''
: 4.67 lbs
Frequency Range
Dynamic Range
Frequency Response
Working Temperature
Power Supply
Battery Time
: 170~260MHz
: 80dB
: 100~10KHz
: 14°F-113°F
: 9V
: 10 hours
-1- -6-

1. Open the battery cover and install a fresh 9V battery, observing the
correct polarity. And then close the cover.
2. Plug in either the clip-on or the headset microphone.
3. To use the clip-on MIC, attach it at chest level. Do not place too close
to the mouth - a distance of about six inches usually works best. To
use the headset MIC, place it on the head and adjust the MIC boom
so that the MIC is about one inch to the side of the front of the mouth.
(Note: The clip-on or headset MIC wire is also the transmitting
antenna. Rolling up or shortening the wire may reduce the effective
operating range. Extend the wire fully during use and keep it as
straight as possible.)
4. Turn on the transmitter by sliding the power switch to ON position.
Power indicator will give a single quick flash, indicating usable battery
strength. In the case of a dead or low battery, the power indicator
either will not go on at all or will stay on continuously, indicating that
the battery should be replaced with a fresh one.
5. The RF indicator on the amplifier should now be lit.
6. Adjust the volume control of body pack and/or volume control of the
amplifier to a comfortable listening level as desired.
7. If the transmitter is not going to be used for any length of time, push
power switch to OFF position and remove the battery.
-5- -2-
1. Echo control
2. Treble control
3. Bass control
4. Power/volume switch
5. MIC IN socket
6. DC IN socket
7. Power indicator
8. Battery charging indicator
9. Wireless receiver RF indicator
10. Wireless receiver antenna
11. MP3 LED display
12. MP3 mode
13. MP3 play/pause/repeat
14. MP3 previous/volume down
15. MP3 next/volume up
16. USB port
17. Microphone holder
18. Speaker
19. Keyboard in socket
20. Cassette in socket
21. REC out socket
22. Battery compartment for
6PCS UM-1 batteries
18
1 2 3 4 5 6 7 8 9
12
13
14
15
16
17
10
11
PARTS DESCRIPTION
19
20
21
22
1. If feedback (howling sound) occurs, try first turning down the treble
control. If feedback still is present, try turning down the volume or
repositioning this unit with respect to the wired or wireless microphone
being used.
2. Extend the antenna fully whenever using the wireless microphone to
ensure optimum performance and maximum range.
ATTENTION:

1. Insert flash drive into USB port or TF card into TF card slot, system
will play the music in flash drive or TF card automatically. If both
flash drive and TF card are inserted, system will play the music in
flash drive. To play music in TF card press MODE button to switch to
SD mode.
2. To play music from your mobile phone etc via bluetooth, press
MODE button to switch to BT mode. Turn on bluetooth function of
your mobile phone and search for Pyle Audio and connect. Then you
can play your music in mobile phone.
Plug one end of provided AC cord into the AC input jack on the left side
of the amplifier. Then plug the other end of AC cord into AC power outlet.
Turn on the unit using the power/volume switch.
This unit can be powered also using external 12V DC power. Connect
external 12V DC power to DC input jack on the front of the amplifier.
Observe the correct polarity as following.
This unit can be powered internally using the built-in rechargeable
battery. When AC power is connected, if battery charging indicator
lights red, the rechargeable battery is not fully charged and will be
allowed to charge while the unit is powered by the AC power. (Note:
Turning off the unit power switch will allow the battery to recharge more
quickly.) If the battery charging indicator lights green, the battery is fully
charged and ready to power the unit alone. Shut off the power switch
and disconnect the AC power. Turn the unit back on and the
rechargeable battery will power the unit alone.
This unit can also be powered internally with (6X) UM-1batteries. Insert
the batteries while observing the correct polarity as marked. For longest
operation use only alkaline or rechargeable batteries. Replace the
batteries when the output volume drops or the range of the wireless
decreases.
Note: This unit does not recharge UM-1 batteries. When use UM-1
batteries, do not connect AC or DC power.
The KEYBOARD IN socket can be connected to a electronics device.
The CASSETTE IN socket can be connected to a cassette player or
other audio player.
The REC OUT socket can be connected to a recording device or to
the input jack of a power amplifier to further amplify and enlarge the
audio power.
The MIC IN socket can be connected to wired dynamic MIC. Keep MIC
head away from the speaker of main unit to avoid feedback.
OPERATION ON AC POWER
NOTE: To avoid damaging your unit, make sure AC power is same as
that marked near AC input jack)
OPERATION ON DC POWER
OPERATION ON RECHARGEABLE BATTERY
OPERATION OF BLUETOOTH/MP3
-3- -4-
OPERATION ON UM-1 BATTERIES
CONNECTION
OPERATION OF BELT PACK TRANSMITTER(OPTIONAL)
9V + Headset MIC Clip-on MIC
Belt
MIC IN Jack
Volume Control
Power Indicator
Power Switch
Battery Cover/
Compartment