Pyle Pro PDBC10 User manual

Owner's Manual
PDBC10
- .... -
<S;:'''l>PYLE " 0 • " • " • 0 • 0 • 0 • " • 0 • PDBCID
PRO =
- -
8 Outlet Rack Mount Power Supply Center
www.pyleaudio.com
718.535.1800 718.236.2400(fax)
1600 63rd Street, Brooklyn NY 11204
Owner's Manual
PDBC10
- .... -
~~~E · 0 • " • " • 0 • " • 0 • " • 0 • ~
--
8 Outlet Rack Mount Power Supply Center
www.pyleaudio.com
718.535.1800 718.236.2400(fax)
1600 63rd Street, Brooklyn NY 11204

OPERATION NOTICE
Thank you for buying our product. Please take a few minutes to read these
operating instructions. These instructions have important product information,
explaining the features and operation
of your unit. Please retain these
instructions for future reference.
1. Be sure that the line voltage of your
outlet
isAC IIOV/60HZ or 220V/50HZ. If
you aren't sure, consult your appliance
dealer or local power company.
2. Protect the voltage line: Avoid putting pressure
on the line. Do not push or pull the line too hard.
3. Do not cover the vents: this product uses vents
to keep the temperature
of the components low.
Covering the vents will damage the unit.
4. Avoid water, dust, and moisture. Keep the unit
dust free and do not place liquids on or near the unit.
5. Avoid putting the unit in low temperatures.
Keep the unit
in a room where the temperature is
above 40 degrees Fahrenheit.
6. Make sure your unit is exposed to air -- do not
operate it in a smaller container
or near a heater.
7. Do not drop metal in the unit. This could
cause a short-circuit and damage your
equipment.
8. Do not open this unit. There are no
user-servicable parts inside. Please contact
qualified personnel
if your unit is not
functioning.
9. Do not clean with volatile solutions. Do not
use alcohol, paint, or gasoline on this product.

CONTROLSAND CONNECTIONS
PLEASE READ THIS MANUAL BEFORE OPERATING THIS UNIT
o
o
Caution :To prevent malfunctioning and/or possible equipment damage:
Before plugging the unit into the power source:
(1 ) the voltage selector
switch should
be set for the correct voltage for your area (115Vand 230V)
and (2) all equipment connected to the crossover outputs should be turned
offand all the inputs turned off.
NOTE: Max power ofeach socket should below 200W
2 3 4 5 6 7 8
1. Power Switch 1 5. Power Switch 5
2.
Power Switch 2 6. Power Switch 6
3.
Power Switch 3 7. Power Switch 7
4.
Power Switch 4 8. Power Switch 8
1&.&1 CE Ef la: °lla : °lla : °lla : °lla : °lla : °lla : °lla : °1
--
2 3 4 5
1. Power output socket 8
2.
Power output socket 7
3.
Power output socket 6
4.
Power output socket 5
5.
Power output socket 4
6 7 8
6. Power output socket 3
7.
Power output socket 2
8.
Power output socket 1
9.
Power Input Cord
10. Fuse
9
o
o
10
CONTROLSAND CONNECTIONS
PLEASE READ THIS MANUAL BEFORE OPERATING THIS UNIT
o
o
Caution :To prevent malfunctioning and/or possible equipment damage:
Before plugging the unit into the power source:
(1 ) the voltage selector
switch should
be set for the correct voltage for your area (115Vand 230V)
and (2) all equipment connected to the crossover outputs should be turned
offand all the inputs turned off.
NOTE: Max power of each socket should below 200W
2 3 4 5 6 7 8
1. Power Switch 1 5. Power Switch 5
2.
Power Switch 2 6. Power Switch 6
3.
Power Switch 3 7. Power Switch 7
4.
Power Switch 4 8. Power Switch 8
1& . &1 CE Ef la: °lla : °lla : °lla : °lla : °lla : °lla : °lla : °1
--
2 3 4 5
1. Power output socket 8
2.
Power output socket 7
3.
Power output socket 6
4.
Power output socket 5
5.
Power output socket 4
6 7 8
6. Power output socket 3
7.
Power output socket 2
8.
Power output socket 1
9.
Power Input Cord
10. Fuse
9
o
o
10