Pyle PCM30A User manual


InstallinganewAmplifierPCM30a




Step1‐Unboxthenewamplifier(fig1)–Setthenewamplifierneartheoldamplifier.
Step2‐Takeapictureofthebackoftheexistingamplifiertologtheoutputconnections.
Step3‐RemovetheRCAInputconnectionfromtheoldamplifier–MoveittotheRCAInputofthenewamplifier.
ThisRCAmale‐to‐malecordconnectstotheRedRCAfemalefromthemusicunit.
Step4‐Ifconnectingthe70voutputtothenewPCM30Aamplifier,thefarbackrightscrewterminalforthe70vwillbe
the“positivewire,“andthescrewterminalnexttoitwillbetheCOM“Negative“youwilluse.
KeepinmindtherearemultipleCOMs.YouwillneedtousetheCOMnearesttothe70vonthefarbackrightsideof
theamplifier.
Step5‐Oncethesetwoconnectionsarecomplete,andtheinputandoutputonthenewamplifierareverified
connected,lookforaSwitchonthebackoftheAmpneartheRed/Whiteinput.ItmustbeswitchedtoAUXPosition.
TheFrontoftheamplifierwillhaveaVolumeknoblabeledMIC2/AUX.Thisvolumecontrolstheinputmusictothe
speakers.Normallyyouwillwanttosetittoa3or4astonothavethemusictooloud.
Afterthisiscomplete,youcanplugthepowerinontheampandturnthepowerbuttonintotheONposition.–Ifyou
donothearmusic,youmayneedtoadjustthevolumeorthemusicsourcemaynotbeonatthistime.

ForissuespleasecalltechsupportwithUnitedMediaSolutionsat800‐373‐8200Opt2

Formusic
inputfeedCOM8ohm COM70V
StandardSetup
BoxSpeakersSetup

InfoLink 4 Port Call Button Interface Installation
1. Connect call button wiring to interface. Strip ¼” to no more than 3/8” insulation from wiring.
The small square buttons near each connection when pressed will release the spring loaded
wire capture mechanism. Depress when inserting wires. A small flat screwdriver can be used
for this purpose.
2. Interface connects easily to the Music Maestro serial port. Use screws for additional support.
3. Power on music system (or power cycle if it was already on when the interface was
connected).
4. When music returns, test button to verify proper operation / message assignment. Adjust if
necessary.
Proper installation. Label wires
with their designated port.
Top view of mounted interface. Note that
no bare copper is exposed.
Use a small screwdriver to depress wire
release for insertion / removal of wire.
DO NOT DO THIS! No bare wire should
extend beyond face of port.


Replacement Preset SanDisk Thumb Drive to Restore Music
There is no need to ship back your UMS music player for a replacement unit. Instead, please locate
the enclosed preset SanDisk thumb drive. This will replace your existing SanDisk thumb drive and
restore music at your location.
Locate the UMS music player (Fig 1). This is usually set up in your phone room.
Confirm you have the HP thin client unit with the UMS Logo sticker on the front.
Locate the flash drive on the back of the unit (Fig 2). It will be a small thumb drive (Fig 3).
Step 1. Unplug the power cord from the music player.
Step 2. Remove the SanDisk drive (Fig 2) and discard.
Insert replacement preset SanDisk thumb drive (Fig 3) into the player.
Step 3. Plug in the power cord.
Step 4. Wait 4 minutes for the music unit to boot up and begin playing.
After completion, please call UMS to confirm the music unit is updated.
1-800-373-8200
You have now completed all the steps necessary to restore the music.
Fig1 Fig2 Fig3

The United Media Solutions PC-Lan based music system.
The Unit will need to be connected with a Network cable - this is how the music unit communicates
channel changes and updates for music and messages.
Installing your UMS LAN connected box.
Find the current Sirius System and place the new system nearby.
1. The Sirius system has a network cable plugged into it.
Disconnect the network cable from the Sirius system and plug it
into the new Maestro system.
2. Plug the new power cord to the back of the system and make
sure the power button is turned on. Power button is located on
the front of the system.
3. Detach old music unit by unplugging the connections, being
Sure to keep the audio output cord nearby.
3. Detach audio output cord from the output headphone jack of
the old music player. It will usually have a male RCA or 3.5mm
Headphone connector. This plugs into the headphone jack of the
new UMS unit.
For Technical Support or any questions,
Please call #800-373-8200 Option 2
Network Cable
Power Cord1
Red-
Overhead Music
White
Do NOT Connect
12” Red/White
Cable fits here
(Headphone jack)
See Fig A
for detail
Fig A
McCoys Lumber Install
NEVER TURN OFF
the system using
the Power Button
Mic NOT used
Do NOT Connect

Info-Link SiriusXM GPRS SIM Chip Exchange
United Media Solutions 4120 Airport Road Cincinnati Ohio 45226 1.800.373.8200 www.unitedmediasolutions.net
Enlarged to show detail
Your new SIM chip is enclosed (fig4). Please locate
your music system and find (fig1) SiriusXM Receiver.
Step 1 - The existing SIM chip (see fig2) is located on
the wireless modem (fig3). To release the card, you
will need to slide the locking retainer, then press in
on the SIM and release. The SIM card will pop out.
The SIM card can now be pulled out.
Remove the existing card, noting the orientation of
chamfered corner of the SIM chip. The new one
needs to be oriented the same way.
Step 2 - Insert the new SIM chip in the slot, with the
chamfered corner oriented the same way as the old
card. Press the chip in until it locks in place. If the
chip will not go all the way in the slot, pull the chip
back out, turn it over and try again.
Once the new SIM chip is seated all the way, slide the
retainer into the locked position
Step 3 - If placed correctly, the wireless modem will
have a green light (fig5).
Please call 800-373-8200 Option 2 for tech support.
Fig 1 SiriusXM Receiver
SiriusXM
Antenna Cable
Fig 4 GPRS SIM Chip
Wireless Modem
Fig 5
Fig 3
Fig 2
Slide to unlock/lock

Exchanging the Power Supply for the SiriusXM radio
Step 1. Locate the SiriusXM music system.
Step 2. Press the Red Button on the power strip to turn off power (fig A).
Step 3. Remove the cable as indicated from the SiriusXM radio (fig B).
Step 4. Remove the power supply from the power strip (fig C).
Step 5. Insert the new power supply into the SiriusXM radio (fig B).
Step 6. Insert the cable into the SiriusXM radio (fig C).
Step 7. Press the Red Button on the power strip (fig A).
Note: It will take the system 4 to 6 minutes to initialize and the music to return.
Fig. A
Fig. B
Fig. C
United Media Solutions/Info-Hold technical support 1-800-373-8200 Option 2
www.infohold.com

Info-Link SiriusXM Setup
United Media Solutions 4120 Airport Road Cincinnati Ohio 45226 1.800.373.8200 www.unitedmediasolutions.net
Fig 2 SiriusXM antenna
(place near window)
Please call your account representative
upon receiving the system.
Step 1 - Using the included power strip (Fig
1) plug the system into a wall outlet with
the system near an external wall.
Step 2 - Place the provided SiriusXM
Antenna (fig 2) near the window pointed
outward, until the green light on the
SiriusXM receiver (fig 3) turns on.
The SiriusXM music should come on
shortly after the green light comes on.
Fig 1
Power Strip
Fig 3 SiriusXM Receiver
SiriusXM
Antenna Cable

Platinum MP-3000 Installation Guide
1. Locate your existing Protege/Audio Emcee MOH player.
2. Locate the audio cord that connects your Protege/Audio Emcee player to the telephone system.
a. On XE-500 models, the audio cord connects on the front of the player. [FIG1]
b. On XE-370 models, the audio cord connects on the back of the player. [FIG 2]
3. Disconnect the audio cord from your Protege/Audio Emcee player.
a. On XE-500 models, you must remove the adapter from the plug. [FIG 3]
4. Plug the audio cord into the line out cord on the MP-3000 (included). [FIG 4]
5. Insert the USB key (included) into the MP-3000 port labeled USB. [FIG 5]
6. Turn on the unit by pressing the power button. [FIG 4]
7. You may adjust the volume of the on-hold messages with the Volume Up or Down buttons located
on the front of the MP-3000 unit. [FIG 4]
For Technical Support, call 1-800-373-8200 Option 2
FIG 1 FIG 2
FIG 3
FIG 4
FIG 5 Volume Power

- InfoLink PC Installation Manual -
System Component Overview 1

- System Installation -
General Installation Considerations
•Every effort should be made to maintain defined wiring color codes.
•The power strip is provided for powering of accessories if necessary.
•All Audio outputs are Line-Level and should be connected to High Impedance loads only!
•Server communication (modem connection) must be verified with United Media Solutions after
installation! (See Below)
 Communication Verification (Required!) 
Installation of the system is not complete until network connectivity is verified with United Media
Solutions, Inc. After installation, call 800-373-8200 and select Option 2 to be connected with customer
service. A representative will verify that the system you’ve installed is registered and communicating
properly with our server(s)!
Mounting the system
The system ships pre-mounted on a backboard and can be mounted in any convenient orientation. A
margin around the system and components is provided for mounting.
AC Power
The system is designed to be powered through the power strip attached to the board. Plug the power
strip plug to a standard AC power outlet and flip the switch on the strip to the On position to power up the
system. The system is shipped shut down and it may be required to press the power button on the front to
initially power on the system. If power is lost to the system after this initial power on, it will automatically
restart without using the power button.
Satellite Radio Antenna Installation
The antenna connection on the radio is a standard female SMB connector and is compatible with all
standard satellite radio antennas and extensions. The antenna must have a clear view to the sky for proper
operation – it must be mounted outside! Install the antenna , route the coax to the system and plug it into the
radio. See chart below for antenna aiming.