Pyle PLMRMP3A User manual

4-Channel Amplifier
PLMRMP3A,PLMRMP3B,PLMRMB4CW,
PLMRMB4CB, PLMRKT4A, PLMRKT4B
USER MANUAL

Installation Precautions
Before you drill or cut any holes, investigate your vessel’s layout
very carefully.
Take special care when you work near the gas tank, fuel lines,
hydraulic lines and electrical wiring.
Never operate the amplifier when it is unmounted. Attach all
audio system components securely within the amplifier to
prevent damage, especially in an accident.
Do not mount this amplifier so that wire connections are
unprotected, in a pinched condition, in contact with any metal
surfaces in your marine vessel, or likely to be damaged by
nearby objects.
Before making or breaking power connections in your system,
disconnect the marine vessel battery. Confirm that your head
unit or other equipment is turned off while connecting the input
jacks and speaker terminals.
1

If you need to replace the power fuse, replace it only with a fuse
idenetical to that supplied with the amplifier, Using a fuse of a
different type or rating may result in damage to your audio
system or your amplifier which is not covered by the
manufacturer’s warranty.
Don't misuse the level control!
Do not mistake the input level control for a volume control! It is
designed ONLY to match the output level of your audio source
to the input level of your amplifier.
Do not adjust this input level to maximum unless your input level
requires it.
Ignoring these instructions will result in an input overload to the
amplifier, and excessive audio distortion. It can also cause the
protection circuit to engage
Controls, Input and Output Cables:
Power and Speaker Wiring
Wire Color
Red
Black
Blue
White
White/Black
Gray
Gray/Black
Green
Green/Black
Purple Purple/Black
Description
Battery (+), 12dc
Barrery (-), Ground
Remote Turn On, 12vdc = ON
CH1 (+)
CH1 (-)
CH2 (+)
CH2 (-)
CH3 (+)
CH3 (-)
CH4 (+)
CH4 (-)
5 2

Full output power level can be determined by turning the gain
control clockwise until the apparent loudness does not appear to
increase any more. Leave the control at the setting where this
begins to become apparent.
4. VOLUME CONTROL Plug for the waterproof remote volume
control. When installed, this control will turn off the Marine
Amplifier Kits when turned all the way down.
5. INPUT Stereo RCA audio input for connecting other audio
devices.
6. To Connect Bluetooth
1. Turn on the amplifier, the red bluetooth indicator LED
keeps blinking at this moment.
2. Look for the "bluetooth" function in your phone setting and
open it.
3. Search the bluetooth device which is "pyle amplifier". After
you connect the bluetooth successfully, the red bluetooth
indicator LED will stay on.
Bluetooth Version: 3.0
Only models PLMRMB4CW and PLMRMB4CB feature
built-in bluetooth.
The switches and gain settings are located behind a watertight
plug, which also lights up when the amplifier is on. Be sure to
replace the plug when finished with adjustments.
1. The INPUT LEVEL switch selects the input sensitivity of the
amplifier. If you are connecting to a LINE level source (typically
any RCA type connection) then the switch should be in the LINE
(out) position. When connecting to loudspeaker outputs or
headphone or high level sources then set the switch to the
SPEAKER (in) position.
2. The POLARITY switch allows the user to optimize bass
performance in the case that there are more than 1 set of
loudspeakers producing bass in the system. Play some music
with strong bass content and listen with the switch alternately in
the NORMAL and REVERSE position until it can be determined
which setting results in more pleasing bass response.
If in doubt, or if any interaction with other speakers is unlikely,
then leave the switch in the NORMAL position.
3. The GAIN control adjusts the overall level of the amplifier.
When using the amplifier without volume control the level should
beset to achieve a balance with other loudspeakers in the
system. As arule, keep the gain setting as low as possible while
still insuring that the system will reach full output power. When
using the system with external volume control, set the external
Volume Control to FULL (clockwise) and adjust the gain on the
amplifier until full output power is reached.
3 4