Pyronix V2GSM User manual
Speaker Microphone
RINS1322-3
GSM Speech Dialler with Automation Control
USER MANUAL
User Manual V2 GSM
Pyronix Ltd Page: 2
CHAPTER 1: CONTENTS PAGE
CHAPTER 1: CONTENTS PAGE ...........................................................................2
CHAPTER 2: INTRODUCTION............................................................................... 3
CHAPTER 3: HOW THE V2 GSM WORKS ............................................................4
3.1 THE V2 GSM PROCESS ............................................................................................... 4
CHAPTER 4: OPERATING THE KEYPAD.............................................................5
4.1 SCROLLING THROUGH MAIN MENUS ........................................................................... 5
4.1.1 Scrolling through main menu ............................................................................... 5
4.1.2 Scrolling through sub menu ................................................................................. 6
4.1.3 Entering a sub menu/main menu function ........................................................... 6
4.2 ENTERING TEXT ........................................................................................................... 6
CHAPTER 5: THE USER MENU ............................................................................ 8
5.1 ENTERING THE USER MENU .......................................................................................... 8
5.2 EXITING THE USER MENU .......................................................................................... 8
5.3 CALL TELEPHONE NUMBER [600] ................................................................................ 9
5.4 ACTIVATING THE ON BOARD 4OUTPUTS ................................................................... 9
5.5 ADDITIONAL OUTPUT CONTROL [700]......................................................................... 10
5.6 PLAY /RECORD VOICE MESSAGES [800] ................................................................... 10
5.7 PLAY /RECORD COMMON MESSAGE [820]........................................................ 11
5.8 PROGRAM SMS MESSAGES [830] ....................................................................... 11
5.9 PROGRAM SMS RESTORE MESSAGES [870] ..................................................... 12
5.10 PROGRAM TELEPHONE NUMBERS [900] ......................................................... 13
5.11 MESSAGE TYPE [930].............................................................................................. 14
5.12 CALL ACKNOWLEDGEMENT CODE [960]................................................................... 15
5.13 COPY ACKNOWLEDGEMENT CODE 1TO ALL [980]................................................... 15
5.14 SET SIM-CARD SECRET PIN [981]............................................................................ 16
5.15 TEST LISTEN IN MICROPHONE [982]......................................................................... 16
5.16 TEST REMOTE SPEAKER [983] ................................................................................. 16
5.17 ENABLE REMOTE LISTEN-IN [984]............................................................................ 16
5.18 VIEW EVENT LOG [985] ........................................................................................... 17
5.19 CHANGE USER CODE [986]...................................................................................... 17
CHAPTER 6: RECEIVING A CALL FROM THE V2 GSM .................................... 18
CHAPTER 7: REMOTE CONTROL VOICE MENU ..............................................19
CHAPTER 8: SMS REMOTE TEXT COMMANDS ............................................... 20
8.1 CHANGING A TELEPHONE NUMBER VIA SMS ........................................................ 20
8.2 ACTIVATING /DEACTIVATING AN OUTPUT VIA SMS ................................................. 20
8.3 READING AN EXTERNAL SYSTEM STATUS VIA SMS .................................................... 21
CHAPTER 9: SHORTCUT FUNCTION REFERENCE..........................................22
CHAPTER 10: INPUTS/OUTPUTS APPENDIX.................................................... 23
10.1 INPUTS .................................................................................................................... 23
10.2 OUTPUTS................................................................................................................. 23
V2 GSM User Manual
Page: 3 Pyronix Ltd
CHAPTER 2: INTRODUCTION
The V2 GSM is 2 way GSM audio communication and remote automation module.
The V2 GSM has the following features:
¾Call any telephone number (just like a mobile phone)
¾Supports 2 way speech via the built on SPK and microphone
¾Activate outputs (to turn on lights, open gates, etc)
oLocally via the integrated keypad
oRemotely via SMS or voice menu command
¾Program voice messages (Up to 14, 1 for each alarm input)
¾Program SMS messages (Up to 14, 1 for each alarm input)
¾Send SMS or voice alerts to up to 9 different user phone numbers
¾View the V2 event log (256 events, time and date)
¾Remotely by phone operate the V2 using the built in voice menu:
oListen in
oTalk and listen
oControl output
oCheck the status of an external device that is connected to the V2 (for
example system armed or disarmed)
¾Remotely by SMS text commands operate the V2:
oChange telephone number
oControl outputs
oCheck the status of an external device that is connected to the V2 (for
example system armed or disarmed)
User Manual V2 GSM
Pyronix Ltd Page: 4
CHAPTER 3: HOW THE V2 GSM WORKS
3.1 THE V2 GSM PROCESS
Below shows a flowchart that is a representation of how the V2 GSM operates, when an
alarm activation occurs.
Alarm
Activation
V2 GSM
Dials Number
V2 GSM Sends
SMS to
Number
User
Answers?
Message
Played. Enter
Ack. Code
Press 99 To
Enter Remote
Menu
V2 GSM
Redials the
telephone
numbers
The next
number is
dialled
SMS received
by user
BEEP
Listen / Talk /
Control
Outputs
Enter User
Code
YES
NO
UNANSWERED
ANSWERED
Press '0' to
hang up (ends
the call)
V2 GSM User Manual
Page: 5 Pyronix Ltd
CHAPTER 4: OPERATING THE KEYPAD
The V2 GSM keypad incorporates 4 status LEDs positioned above the LCD display. They
are numbered 1 to 4 and are used to show the status of the 4 inbuilt outputs.
4.1 SCROLLING THROUGH MAIN MENUS
4.1.1 Scrolling through main menu
TO SCROLL THROUGH MAIN MENU’S. PRESS THE AND KEYS
MAIN MENU ITEMS ARE IN CAPITAL LETTERS
User Manual V2 GSM
Pyronix Ltd Page: 6
4.1.2 Scrolling through sub menu
TO SCROLL THROUGH SUB MENU’S. PRESS THE %AND &KEYS
SUB MENU ITEMS ARE IN CAPITAL LETTERS
4.1.3 Entering a sub menu/main menu function
TO ENTER A ANY FUNCTION. PRESS THE KEY
Press to exit a sub-menu, and to go back to the main menu functions, press
until a main menu function (in capital letters) is displayed. Function numbers can be
entered to jump to a particular menu. For example to leave the V2GSM from any main
menu or sub-menu digit [999] that will bring you to ‘QUIT/EXIT PROGRAMMING’.
4.2 ENTERING TEXT
The numeric keys above are used to enter the text onto the V2GSM (for SMS texts).
For example to enter the letter ‘Q’. The key needs to be entered twice. The key is
used to enter a space.
V2 GSM User Manual
Page: 7 Pyronix Ltd
Keys Operation Example Display
Enters a function / starts a
command
Exits a function / stops a
command
!
Activates output 1
Enters a ‘+’ symbol before a
telephone number if required.
"
Activates output 2
Enters a ‘*’ symbol when dialling
a number if required.
#
Activates output 3
Alternates between capitals and
lower case
Enters a ‘#’ symbol when dialling
a number if required.
$
Activates output 4
Deletes the current character /
number that the cursor is on
&
Scrolls between sub-menu items
Moves the character cursor to
the end of a string
%
Scrolls between sub-menu items
Moves the character cursor to
the beginning of a string
Scrolls between main-menu
items
Moves the character cursor to
the left
Scrolls between main-menu
items
Moves the character cursor to
the right
User Manual V2 GSM
Pyronix Ltd Page: 8
CHAPTER 5: THE USER MENU
5.1 ENTERING THE USER MENU
Using the keypad enter the user
code.
Default = 1234
‘[600] CALL TELEPHONE NUMBER’
will be displayed which indicates you
are in the user menu.
Use the and keys to scroll
through the main menus.
Press to enter a function.
5.2 EXITING THE USER MENU
To exit the user menu, type in ‘999’ or
scroll to
“QUIT / EXIT PROGRAMMING”
Press the key.
V2 GSM User Manual
Page: 9 Pyronix Ltd
5.3 CALL TELEPHONE NUMBER [600]
This function allows the user to make an outgoing call. Enter the telephone number you
would like to call and press .
Press the or keys to scroll to
‘CALL TELEPHONE NUMBER’ or
enter ‘600’. Press
Enter the telephone number to dial
and press . Press to end the
call.
During the call you can increase or
decrease the volume by using the
up/down arrow keys.
For certain dialling sequences, a "
for ‘*’ or #for a ‘#’ symbol may
need to be used.
5.4 ACTIVATING THE ON BOARD 4 OUTPUTS
To activate the 4 onboard outputs there is no need to enter the user menu. They can be
activated / deactivated by pressing the required number key for 2 sec:
Press and hold !to activate output 1.
The LED 1 output will illuminate
Press and hold "to activate output 2.
The LED 2 output will illuminate
Press and hold #to activate output 3.
The LED 3 output will illuminate
Press and hold $to activate output 4.
The LED 4 output will illuminate
User Manual V2 GSM
Pyronix Ltd Page: 10
5.5 ADDITIONAL OUTPUT CONTROL [700]
The V2GSM comes with 4 already built in outputs. Up to an additional of 48 outputs could
be added by using 8 output expander modules. The output control feature is used to
control the status of the additional V2GSM programmable outputs (PGMs).
Press the or keys to scroll to
‘OUTPUT CONTROL’ or enter ‘[700]’.
Press
Press %or &to select the PGM
number (up to 52) Press
Press %or &to turn the output on
or off or select the number:
= Output off (default)
= Output on
Press
700 – 704 for the on board V2GSM outputs. 751 – 799 for the expander outputs.
5.6 PLAY / RECORD VOICE MESSAGES [800]
Voice messages can be programmed for each input on the V2GSM. The voice alarm
messages can be up to 12 sec long. At default there are no user recordings.
Press the or keys to scroll to
‘PLAY/REC VOICE MESSAGES’ or
enter ‘800’. Press
Press %or &to select which input
number (or enter the shortcut function
number see page 10) Press
Press:
= To play a message
= To record
= To delete
Shortcut Function Numbers:
INPUTS BUILT ON V2GSM INPUTS ON THE EXPANDER MODULE
801: Play/rec msg for input#1 807: Play/rec msg for input#7
802: Play/rec msg for input#2 808: Play/rec msg for input#8
803: Play/rec msg for input#3 809: Play/rec msg for input#9
804: Play/rec msg for input#4 810: Play/rec msg for input#10
805: Play/rec msg for input#5 811: Play/rec msg for input#11
806: Play/rec msg for input#6 812: Play/rec msg for input#12
813: Play/rec msg for input#13
814: Play/rec msg for input#14
V2 GSM User Manual
Page: 11 Pyronix Ltd
5.7 PLAY / RECORD COMMON MESSAGE [820]
This message, is played each time an activation has occurred and is heard at the end of
an input activation message. The common message can be 20 seconds long.
Press the or keys to scroll to
‘PLAY/REC VOICE MESSAGES’ or
enter ‘820’.
Press
Press:
= To play a message
= To record
= To delete
Press
5.8 PROGRAM SMS MESSAGES [830]
SMS messages can be programmed for each alarm input. At default there are no pre-
programmed messages.
Press the or keys to scroll to
‘PROGRAM SMS MESSAGES’ or
enter ‘830’. Press
Press %or &to select which input
number for the SMS message (or
enter the shortcut function number
see below) Press
Enter the text message using the
relevant keys (see page 6 for help on
entering text). A maximum of 160
characters may be used. Press
Shortcut Function Numbers:
INPUTS BUILT ON V2GSM INPUTS ON THE EXPANDER MODULE
831: SMS msg for input: 1 837: SMS msg for input: 7
832: SMS msg for input: 2 838: SMS msg for input: 8
833: SMS msg for input: 3 839: SMS msg for input: 9
834: SMS msg for input: 4 840: SMS msg for input: 10
835: SMS msg for input: 5 841: SMS msg for input: 11
836: SMS msg for input: 6 842: SMS msg for input: 12
843: SMS msg for input: 13
844: SMS msg for input: 14
User Manual V2 GSM
Pyronix Ltd Page: 12
5.9 PROGRAM SMS RESTORE MESSAGES [870]
SMS restore messages can be programmed for each alarm event (to see which inputs are
connected to what alarm events please see the appendix page 23). At default there are no
pre-programmed messages.
Press the or keys to scroll to
‘PROGRAM SMS REST.
MESSAGES’ or enter ‘870’.
Press
Press %or &to select which input
number for the SMS restore message
(or enter the shortcut function number
see below)
Press
Enter the text message using the
relevant keys (see page 6 for help on
entering text). A maximum of 160
characters may be used.
Press
Shortcut Function Numbers:
INPUTS BUILT ON V2GSM INPUTS ON THE EXPANDER MODULE
871: SMS rest. msg for input: 1 877: SMS rest. msg for input: 7
872: SMS rest. msg for input: 2 878: SMS rest. msg for input: 8
873: SMS rest. msg for input: 3 879: SMS rest. msg for input: 9
874: SMS rest. msg for input: 4 880: SMS rest. msg for input: 10
875: SMS rest. msg for input: 5 881: SMS rest. msg for input: 11
876: SMS rest. msg for input: 6 882: SMS rest. msg for input: 12
883: SMS rest. msg for input: 13
884: SMS rest. msg for input: 14
V2 GSM User Manual
Page: 13 Pyronix Ltd
5.10 PROGRAM TELEPHONE NUMBERS [900]
Up to 9 telephone numbers can be programmed on the V2 GSM. Your Engineer will have
already assigned the desired alarm messages to one or more telephone numbers.
The V2GSM will support up to 14 Voice/SMS messages. One for each alarm input.
Press the or keys to scroll to
‘PROGRAM TELEPHONE
NUMBERS’ or enter ‘900’.
Press
Press %or &to select which
telephone number to be programmed
(or enter the shortcut function
number).
Press
Enter the telephone number and
press
If dialling abroad, use the !key to
enter a ‘+’ symbol.
Menu Shortcut Function Numbers:
901: telephone number #1
902: telephone number #2
903: telephone number #3
904: telephone number #4
905: telephone number #5
906: telephone number #6
907: telephone number #7
908: telephone number #8
909: telephone number #9
User Manual V2 GSM
Pyronix Ltd Page: 14
5.11 MESSAGE TYPE [930]
This function allows the choice of what message type is sent for each telephone number.
The following different message types can be programmed:
Voice: Sends a voice message only (example: ALARM, ALARM, ALARM).
Voice + Common: Sends a voice message and common message (example: ALARM,
ALARM, ALARM. This is Mr and Mrs Jones of West Street).
SMS: Sends an SMS text only (example: Text Message = ALARM, ALARM, ALARM)
Press the or keys to scroll to
‘MESSAGE TYPE’ or enter ‘930’.
Press
Press %or &to select which
message type for which telephone
number needs to be programmed (or
enter the programmed function
number).
Press
Press %or &to select which
message type or select the number:
= Voice = Default
= Voice + common
= SMS
Press
Menu Shortcut Function Numbers:
931: Message type for tel#1
932: Message type for tel#2
933: Message type for tel#3
934: Message type for tel#4
935: Message type for tel#5
936: Message type for tel#6
937: Message type for tel#7
938: Message type for tel#8
939: Message type for tel#9
V2 GSM User Manual
Page: 15 Pyronix Ltd
5.12 CALL ACKNOWLEDGEMENT CODE [960]
When the V2GSM calls a telephone number, the relevant message will be played. At the
end of the message the V2GSM will ask you to enter a code number to acknowledge that
the message has been received. If the call is not acknowledged then the V2GSM will
make a repeat call.
This code is programmable and can be anything from up to 1 to 10 digits long.
Press the or keys to scroll to
‘CALL ACKNOWLEDGE CODE’ or
enter ‘960’. Press
Press %or &to select the call
acknowledgement code for the
telephone number (or enter the
programmed function number).
Press
Enter the code.
Press
Default = 5.
Menu Shortcut Function Numbers:
961: Call ack. code for tel:1 966: Call ack. code for tel:6
962: Call ack. code for tel:2 967: Call ack. code for tel:7
963: Call ack. code for tel:3 968: Call ack. code for tel:8
964: Call ack. code for tel:4 969: Call ack. code for tel:9
965: Call ack. code for tel:5
5.13 COPY ACKNOWLEDGEMENT CODE 1 TO ALL [980]
This function supplies a shortcut to copy the acknowledgement code programmed in
telephone number 1 (function 961) to all 8 other telephone numbers.
Press the or keys to scroll to
‘COPY ACK CODE 1 TO ALL’ or
enter ‘980’.
Press
Press %or &to select the Yes or
No or select the number:
= No = Default
= Yes
Press
User Manual V2 GSM
Pyronix Ltd Page: 16
5.14 SET SIM-CARD SECRET PIN [981]
Press the or keys to scroll to
‘SECRET SIM-CARD SECRET PIN’
or enter ‘981’.
Press
Enter the code.
Press
5.15 TEST LISTEN IN MICROPHONE [982]
This tests the built in microphone.
Press the or keys to scroll to
‘TEST LISTEN-IN MIC’ or enter ‘982’.
Press
The V2 GSM is now testing the
Microphone, press to stop the
test.
5.16 TEST REMOTE SPEAKER [983]
This tests the Remote speaker if connected one.
Press the or keys to scroll to
‘TEST REMOTE SPEAKER’ or enter
‘983’.
Press
The V2 GSM is now testing the
speaker.
Press to stop the test.
5.17 ENABLE REMOTE LISTEN-IN [984]
Press the or keys to scroll to
‘ENABLE REMOTE LISTEN IN’ or
enter ‘984’.
Press
Press %or &to select the Yes or
No to select the number below to
enable remote listen in:
= No
= Yes = Default
Press
V2 GSM User Manual
Page: 17 Pyronix Ltd
5.18 VIEW EVENT LOG [985]
All events that occur are recorded in the event log. The V2 GSM display will show all
information in order, starting at the most recent event.
The above display shows the following:
001 = Event number (up to 256 events can be logged)
00:32 = Time
010110 = Date (DD:MM:YY)
Press the or keys to scroll to
‘VIEW EVENT LOG’ or enter ‘985’.
Press
Press %or &to scroll back and
forth through the log. Press the
key to jump to the last event.
Press to exit.
5.19 CHANGE USER CODE [986]
The user code can be up to 4 digits.
Press the or keys to scroll to
‘CHANGE USER CODE’ or enter
‘986’.
Press
Enter the new user code,
press
Default user code = 1234
User Manual V2 GSM
Pyronix Ltd Page: 18
CHAPTER 6: RECEIVING A CALL FROM THE V2 GSM
After an alarm activation has occurred, the V2 GSM will call one or more of the
programmed telephone numbers.
Voice Alarm Transmission:
¾V2 GSM dials the programmed telephone number
¾The user answers the call
¾Voice Alarm Message is played
¾V2GSM will ask for call acknowledgement code
¾The user will enter the required acknowledgement code to acknowledge the call
¾A long beep is heard and the call will be finished
¾At the end of the long beep, If the ‘9’ key is pressed twice (99) a remote control
menu is entered (if enabled by the engineer).
SMS Alarm Transmission:
¾V2 GSM dials the programmed telephone number
¾The user receives the alarm SMS message
V2 GSM User Manual
Page: 19 Pyronix Ltd
CHAPTER 7: REMOTE CONTROL VOICE MENU
The V2GSM remote control menu can be accessed in two different ways:
Method 1:
After acknowledging an alarm call at the end of the long beep, If the ‘9’ key is pressed
twice (99) the remote control menu is entered (if enabled by the engineer).
Method 2:
Call the V2GSM telephone number. After a pre-programmed number of rings the V2GSM
will answer-
¾The V2GSM voice menu will ask you:
Enter your user code. This is the same code that is used to enter the user
menu on the V2 GSM.
¾After entering a valid user code the V2GSM voice menu will say:
Enter your command number or press ‘9’ for help. The command
numbers available on the V2GSM are as follow:
Press 1 = listen
Press 2 = talk and listen full duplex
Press 3 = control output
Press 4 = external device system status
Press 5 = external SPK listen (if installed)
Press 6 = external SPK and Microphone talk and listen (if installed)
Press 0 = to hang up.
¾If you press 9 for help the following messages will be played:
Press 1 to listen, 2 to talk and listen, 3 to control output, 4 for system
status or press 0 to hang up.
¾If you decided to control an output, press 3. The voice menu on V2GSM will say:
Enter the output number. Enter the output that you wish to operate. 1 to 4
for the build in outputs and 51 to 99 for the external outputs if installed (see
the output appendix on page 23).
¾After choosing an output to control the voice menu on V2GSM will say:
Press ‘1’ to turn on, ‘0’ to turn off. This turns on and off the chosen
output.
¾If you decided to check the external system status, press “4” key. The V2GSM will
say:
Armed or Disarmed. This function needs to be enabled by the Engineer.
¾To exit the V2GSM voice menu press “0” key. The voice menu will say:
‘Goodbye’
User Manual V2 GSM
Pyronix Ltd Page: 20
CHAPTER 8: SMS REMOTE TEXT COMMANDS
SMS text commands can be sent to the V2 GSM to initiate certain commands.
8.1 CHANGING A TELEPHONE NUMBER VIA SMS
- To change a telephone number on the V2GSM, send the
following SMS text command:
Example: CHANGE 1 TO +447711700200
This means that telephone “1” will change to the following
number: “+447711700200”.
- If you would like to receive confirmation of the phone
number change, add to the command string CONFIRM.
Example: CHANGE 1 TO +447711700200 CONFIRM
The V2GSM will then send an SMS back to your mobile
phone showing the new phone number in the following
format:
Example Feedback: V2-GSM: TEL#1: +447711700200
PLEASE NOTE IT IS ONLY POSSIBLE TO CHANGE A TELEPHONE NUMBER IF IT
ALREADY EXISTS. TELEPHONE NUMBERS CANNOT BE ADDED.
8.2 ACTIVATING / DEACTIVATING AN OUTPUT VIA SMS
1) To activate an output remotely send the following SMS
text command:
Example: PGM 3 ON
2) To deactivate an output remotely send the following SMS
text command:
Example: PGM 3 OFF
- If you would like to receive confirmation of the output
status change, add to the command string CONFIRM.
Example: PGM 3 ON CONFIRM
The V2GSM will then send an SMS back to your mobile
phone showing the new change of the PGM 3 status.
Example Feedback: V2-GSM: PGM#3 = ON
Other manuals for V2GSM
1
Table of contents
Other Pyronix Intercom System manuals
