Python 571XP User manual

MMooddeell557711XXPP
➤
OOwwnneerr’’ssGGuuiiddee

i
© 2005 directed electronics—all rights reserved
lliimmiitteeddlliiffeettiimmeeccoonnssuummeerrwwaarrrraannttyy
Directed Electronics ("Directed") promises to the original purchaser to repair or replace
with a comparable reconditioned model any Directed unit (hereafter the "unit"), exclud-
ing without limitation the siren, the remote transmitters, the associated sensors and acces-
sories, which proves to be defective in workmanship or material under reasonable use dur-
ing the lifetime of the vehicle provided the following conditions are met: the unit was pro-
fessionally installed and serviced by an authorized Directed dealer; the unit will be pro-
fessionally reinstalled in the vehicle in which it was originally installed by an authorized
Directed dealer; and the unit is returned to Directed, shipping prepaid with a legible copy
of the bill of sale or other dated proof of purchase bearing the following information: con-
sumer's name, telephone number and address; the authorized dealers name, telephone
number and address; complete product description, including accessories; the year, make
and model of the vehicle; vehicle license number and vehicle identification number. All
components other than the unit, including without limitation the siren, the remote trans-
mitters and the associated sensors and accessories, carry a one-year warranty from the date
of purchase of the same. This warranty is non-transferable and is automatically void if: the
original purchaser has not completed the warranty card and mailed it within ten (10) days
of the date of purchase to the address listed on the card; the unit's date code or serial num-
ber is defaced, missing or altered; the unit has been modified or used in a manner con-
trary to its intended purpose; the unit has been damaged by accident, unreasonable use,
neglect, improper service, installation or other causes not arising out of defects in materi-
als or construction. The warranty does not cover damage to the unit caused by installa-
tion or removal of the unit. Directed, in its sole discretion, will determine what consti-
tutes excessive damage and may refuse the return of any unit with excessive damage. TO
THE MAXIMUM EXTENT ALLOWED BY LAW, ALL WARRANTIES, INCLUD-
ING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY,
WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE
AND WARRANTY OF NON-INFRINGEMENT OF INTELLECTUAL PROPERTY,
ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR
AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY,
OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS.
DIRECTED DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY
AND ALL ACTS OF THIRD PARTIES INCLUDING ITS AUTHORIZED DEAL-
ERS OR INSTALLERS. DIRECTED SECURITY SYSTEMS, INCLUDING THIS
UNIT, ARE DETERRENTS AGAINST POSSIBLE THEFT. DIRECTED IS NOT
OFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM, DAM-
AGE OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS; AND
HEREBY EXPRESSLY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUD-
ING WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE AND/OR
VANDALISM. THIS WARRANTY DOES NOT COVER LABOR COSTS FOR
MAINTENANCE, REMOVAL OR REINSTALLATION OF THE UNIT OR ANY

ii © 2005 directed electronics—all rights reserved
CONSEQUENTIAL DAMAGES OF ANY KIND. IN THE EVENT OF A CLAIM
OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER
VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA.
CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY
AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY
CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE
AUTHORIZED DIRECTED DEALER'S PURCHASE PRICE OF THE UNIT.
DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEV-
ER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES,
INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF
EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY
AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER
DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE CON-
TROL MODULE AS DESCRIBED ABOVE. Some states do not allow limitations on
how long an implied warranty will last or the exclusion or limitation of incidental or con-
sequential damages. This warranty gives you specific legal rights and you may also have
other rights that vary from State to State.
This product may be covered by a Guaranteed Protection Plan ("GPP"). See your autho-
rized Directed dealer for details of the plan or call Directed Customer Service at 1-800-
876-0800. Directed security systems, including this unit, are deterrents against possible
theft. Directed is not offering a guarantee or insurance against vandalism, damage or theft
of the automobile, its parts or contents; and hereby expressly disclaims any liability what-
soever, including without limitation, liability for theft, damage and/or vandalism.
Directed does not and has not authorized any person or entity to create for it any other
obligation, promise, duty or obligation in connection with this security system.
Make sure you have all of the following information from your dealer:
A clear copy of the sales receipt, showing the following:
➤Date of purchase
➤Your full name and address
➤Authorized dealer's company name and address
➤Type of alarm installed
➤Year, make, model and color of the automobile
➤Automobile license number
➤Vehicle identification number
➤All security options installed on automobile
➤Installation receipts

1
© 2005 directed electronics—all rights reserved
lliimmiitteeddlliiffeettiimmeeccoonnssuummeerrwwaarrrraannttyy................................................................................ii
wwhhaattiissiinncclluuddeedd....................................................................
..........................................33
iimmppoorrttaannttiinnffoorrmmaattiioonn...................................
.................................................................33
your warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
fcc/id notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
caution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
22--wwaayyrreemmootteeddiiaaggrraamm...........
.........................................................................................55
ssttaannddaarrdd
rreemmootteeccoonnffiigguurraattiioonn........................................................................................55
22--wwaayyrreemmootteeffuunnccttiioonnss....................................................................
..............................66
standard configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
rreemmootteeooppeerraattiioonn..................................................
........................................................88
system signal paging features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
out of range notification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
pprrooggrraammmmiinnggrreemmoottee......................
..............................................................................1100
uussiinnggyyoouurrssyysstteemm.
.......................................................................................................1111
warning! safety first. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
locking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
unlocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
panic mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
valet mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
remote start. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
rear defogger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
valet take-over. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
short-run/turbo. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
timer mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
aauuxxiilliiaarryyoouuttppuuttss((ooppttiioonnss)).................................................................
...........................2233
ssaaffeettyyffeeaattuurreess.......................................................
.........................................................2244
starter anti-grind circuitry. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
disabling the remote start system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
over and under rev protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
shut down inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
ccooddeehhooppppiinngg..........................
......................................................................................2255
hhiigghhffrreeqquue
ennccyy.................................................................................................
.............2266
oowwnneerrrreeccooggnniittiioonn...................................................................
.....................................2266
rraappiiddrreessuummeellooggiicc..........................................
..............................................................2277
ppoowweerrssaavveerrmmooddee...................
.....................................................................................2277
pprrooggrraammmmiinngg
ooppttiioonnss..................................................................................................2288
sseeccuurriittyy&&ccoonnvveenniieenncceeeexxppaannssiioonnss...........................................................
...................2299
gglloossssaarryyoofftteerrmmss.............................................................
.............................................3311
ttaabblleeooffccoonntteennttss

2© 2005 directed electronics—all rights reserved

3
© 2005 directed electronics—all rights reserved
wwhhaattiissiinncclluuddeedd
➤A control module
➤An XHF2 receiver/antenna
➤One 4-button 2-way remote
➤One 4-button remote
➤A in-vehicle status LED indicator light
➤A push-button Valet switch
➤Your warranty registration
➤A shut-down toggle switch
iimmppoorrttaannttiinnffoorrmmaattiioonn
Congratulations on the purchase of your 2-way remote start
keyless entry system. Due to the complexity of this system, it
must be installed by an authorized dealer only. Installation of this
product by anyone other than an authorized dealer voids the
warranty. All dealers are provided with a preprinted dealer certif-
icate to verify that they are authorized.
By carefully reading this Owner's Guide prior to using your
system, you will maximize the use of this system and its features.
You can print additional or replacement copies of this manual by
accessing our web site at www.directed.com.

4© 2005 directed electronics—all rights reserved
your warranty
Your warranty registration must be completely filled out and
returned within 10 days of purchase. Your product warranty
will not be validated if your warranty registration is not returned.
Make sure you receive the warranty registration from your dealer.
It is also necessary to keep your proof of purchase, which reflects
that the product was installed by an authorized dealer.
fcc/id notice
This device complies with Part 15 of FCC rules. Operation is
subject to the following conditions: (1) This device may not
cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause
undesirable operation.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate this device.
caution
This product is designed for fuel injected, automatic transmission
vehicles only. Use of this product in a standard transmission
vehicle is dangerous and contrary to the product's intended use.
➜
➜
➜

5
© 2005 directed electronics—all rights reserved
22--wwaayyrreemmootteeddiiaaggrraamm
ssttaannddaarrddrreemmootteeccoonnffiigguurraattiioonn
1. Unlock/Lock Indicator (Orange)
2. Receive/Transmit Indicator (Green)
3. Remote Start/Auxiliary Indicator (Yellow)
4. Panic Indicator (Red)
5. Lock Button
6. Unlock Button
7. Remote Start Button
8. Auxiliary Channel Button
1
2
3
4
56
78

6© 2005 directed electronics—all rights reserved
ssyysstteemmmmaaiinntteennaannccee
This system needs no specific maintenance beyond remote
control battery replacement. The remote is powered by a 1.5V
AAA battery.
Low Battery Notification
If the battery is low (and this feature is programmed On) the 2-
way remote will emit 2 long beeps 5-seconds after a transmission
is completed. The 2 long beeps will repeat every 25 seconds up
to 3 times (or until a 2-way remote button is pressed).
Battery Replacement
Gently pull the end of the battery door away from the top of the
remote control then slide the door up to expose the battery and
remove the expired battery. Place the new battery into the
remote control observing the correct polarity. When power is
returned the remote control will light all icons and generate
melodies (representing all beeper tones).
22--wwaayyrreemmootteeffuunnccttiioonnss
The receiver uses a computer-based Learn Routine to learn the
2-way remote buttons. This makes it possible to assign any 2-
way remote button to any receiver function. The 2-way remote
initially comes programmed with Standard Configuration, but
may also be customized by an authorized dealer. The buttons in
all of the instructions in this manual correspond to a Standard
Configuration 2-way remote.

7
© 2005 directed electronics—all rights reserved
standard configuration
Button
Controls the system Lock function by briefly pressing this
button.
Button
Controls the system Unlock function by briefly pressing this
button.
Button
Controls an optional auxiliary function, such as trunk release,
can be controlled by pressing this button for 1.5 seconds.)
The auxiliary output controls __________________________.
Button
The remote start feature is turned On/Off by pressing this button twice.
and Buttons
The remote start timer mode function of the system is controlled
by pressing these buttons simultaneously.
and Buttons
The Turbo/Short Run feature is controlled by these buttons (refer
to the Turbo/Short Run section for additional details).
and Buttons
An optional auxiliary convenience or expansion function that
you have added to your system can be activated by pressing these
buttons simultaneously.
The auxiliary output controls __________________________.
➜

8© 2005 directed electronics—all rights reserved
Button
Press and hold this button for 3-seconds to enter Panic Mode.
and and Buttons
When simultaneously pressed these buttons control the rear
window defogger during remote starting.
rreemmootteeooppeerraattiioonn
The remote start system operates at 434 MHz and incorporates
Directed’s proprietary XHF2 out-board technology transceiver. The
high frequency combined with Binary Data communication achieves
superior range with two-way communication.
system signal paging features
A page is the signal the control module sends to the remote control
as confirmation of receipt of a command or alarm system status.
When the remote control receives a page it will generate a page noti-
fication to the user (notifications are audible beeps) and the LED
Icons will display the current system status.
Command Page
When a command (arm/disarm, remote start, or auxiliary
channel) from the remote control is sent and received, the system
will send a command page back to confirm receipt.
Alarm Page
➜

9
© 2005 directed electronics—all rights reserved
If the ignition is turned on while locked, the system will actuate
the panic feature and an Alarm Page will be sent to the remote
control. When the remote receives this Alarm Page, the remote
control will generate 4 beeps 5 times and the Red LED will illu-
minate for 3-seconds. This will repeat every 100 seconds to alert
the user that the security feature was triggered and will continue
until the alarm page is cleared.
Page Recognition
To clear a page alert/notification, quickly press any button on the
remote control. This can be performed at any time during or after
the page notification has occurred.
The remote control will not send a command to the system at
this time; it will only clear future repeats of the page notification.
The next time a button is pressed on the remote control it will
send a command to the system.
out of range notification
If a command is issued from the remote, but the remote is
beyond the range of the vehicle to receive the command, the
remote responds with 2 sets of 3 quick beeps and the Green LED
will flash 6-times.
➜

10 © 2005 directed electronics—all rights reserved
pprrooggrraammmmiinnggrreemmoottee
To enter programming mode
Press and hold all four remote control buttons simultaneously
until one long beep is heard. Programming mode is now entered.
Beeps On/Off
Press to select beeps On/Off. One beep is notification beeps
On, Two beeps is notification beeps Off. The notification beeps
are programmed On from the factory and can be programmed
Off if they are not desired. When programmed Off the remote
will only flash the LEDs as notification of a command page or an
alarm page.
Remote battery low notification
Press to select low battery notification On/Off. One beep is
low battery notification On. Two beeps is low battery notification
Off. The Low battery Beeps are programmed On from the
factory and can be programmed Off if they are not desired.
When programmed Off the remote will not give any notification
that the battery charge level in the remote is low.
Page notification
The remote control can be programmed to notify the user of a
page (audibly beeping if the vehicle’s status changes, e.g. door
unlocked, engine started, vehicle violation, etc.). Press to
select page On/Off. One beep is page On, Two beeps is page Off.
When programmed off the remote will not give any notification
that a page was received from the vehicle.

11
© 2005 directed electronics—all rights reserved
To exit programming mode
The remote control will exit programming mode after 2-seconds
of inactivity and will emit 2 long beeps.
uussiinnggyyoouurrssyysstteemm
warning! safety first
The following safety warnings must be observed at all times:
➤Due to the complexity of this system, installation of this product
must only be performed by an authorized Directed dealer.
➤When properly installed, this system can start the vehicle via
a command signal from the 2-way remote control. Therefore,
never operate the system in an enclosed area or partially
enclosed area without ventilation (such as a garage). When
parking in an enclosed or partially enclosed area or when
having the vehicle serviced, the remote start system must be
disabled using the installed toggle switch. It is the user's sole
responsibility to properly handle and keep out of reach from
children all 2-way remotes to assure that the system does not
unintentionally remote start the vehicle. THE USER MUST
INSTALL A CARBON MONOXIDE DETECTOR IN
OR ABOUT THE LIVING AREA ADJACENT TO THE
VEHICLE. ALL DOORS LEADING FROM ADJACENT
LIVING AREAS TO THE ENCLOSED OR PARTIALLY
ENCLOSED VEHICLE STORAGE AREA MUST AT
➜

12 © 2005 directed electronics—all rights reserved
ALL TIMES REMAIN CLOSED. These precautions are
the sole responsibility of the user.
➤Use of this product in a manner contrary to its intended
mode of operation may result in property damage, personal
injury, or death. (1) Never remotely start the vehicle with the
vehicle in gear, and (2) Never remotely start the vehicle with
the keys in the ignition. The user must also have the neutral
safety feature of the vehicle periodically checked, wherein
the vehicle must not remotely start while the car is in gear.
This testing should be performed by an authorized Directed
dealer in accordance with the Safety Check outlined in the
product installation guide. If the vehicle starts in gear, cease
remote start operation immediately and consult with the
authorized Directed dealer to fix the problem.
➤After the remote start module has been installed, contact
your authorized dealer to have him or her test the remote
start module by performing the Safety Check outlined in the
product installation guide. If the vehicle starts when
performing the Neutral Safety Shutdown Circuit test, the
remote start unit has not been properly installed. The
remote start module must be removed or the installer must
properly reinstall the remote start system so that the vehicle
does not start in gear. All installations must be performed by
an authorized Directed dealer. OPERATION OF THE
REMOTE START MODULE IF THE VEHICLE
STARTS IN GEAR IS CONTRARY TO ITS INTENDED
MODE OF OPERATION. OPERATING THE

13
© 2005 directed electronics—all rights reserved
REMOTE START SYSTEM UNDER THESE CONDI-
TIONS MAY RESULT IN PROPERTY DAMAGE OR
PERSONAL INJURY. YOU MUST IMMEDIATELY
CEASE THE USE OF THE UNIT AND SEEK THE
ASSISTANCE OF AN AUTHORIZED Directed DEALER
TO REPAIR OR DISCONNECT THE INSTALLED
REMOTE START MODULE. DIRECTED WILL NOT
BE HELD RESPONSIBLE OR PAY FOR INSTALLA-
TION OR REINSTALLATION COSTS.
locking
Pressing for one second arms the system by activating the
starter kill and locking the doors (if the door locks are
connected). The horn will honk (if connected) and the parking
lights will flash once to confirm arming of the system. While the
system is armed, the in-vehicle status LED will flash once per
second. The Failsafe®Starter Kill will also prevent the vehicle’s
starter from cranking.
The system can also be programmed to arm the optional Failsafe®
Starter Kill automatically (called Passive Mode). If the system has
been programmed for Passive Mode, the Failsafe®Starter Kill will
automatically activate 30 seconds after the ignition has been
turned off. After the ignition has been turned off, the in-vehicle
status LED will flash rapidly to indicate that the system is in
Passive Mode.
➜

14 © 2005 directed electronics—all rights reserved
If Passive Mode has been programmed on, then it is also possible
to program the system for Passive Locking. With Passive Locking,
the vehicle doors lock automatically at the same time that the
Failsafe®Starter Kill is activated. If Passive Locking is
programmed on, care must be taken to prevent the keys from
being locked in the vehicle.
The remote responds to active arming with one beep and the
Orange LED will flash 3-times to indicate successful locking of
the system.
If after 2-seconds the remote beeps once, the Orange LED flashes
6-times and the Red LED lights for 3-seconds, the system has
detected an open hood.
unlocking
Pressing for one second disarms the system and unlocks the
doors (if connected). The horn will honk twice (if connected)
and the parking lights will flash twice to confirm disarming of the
system. The optional Failsafe®Starter Kill will be deactivated.
The in-vehicle status LED will turn off, unless the system is pro-
grammed for Passive Mode. In Passive Mode, the in-vehicle status
LED will flash rapidly when the system is disarmed. This indi-
cates that the system will re-engage the starter kill and re-lock the
doors (if Passive Locking has been programmed) in 30 seconds
unless the ignition is turned on.
➜
nnoottee::For Passive Mode to be effective, the Failsafe®
Starter Kill relay must be installed.

15
© 2005 directed electronics—all rights reserved
The remote will indicate unlock notification with 2 beeps and 3
flashes of the Orange LED.
disabling the starter kill without a 2-way remote
If your 2-way remote is lost or damaged, you can manually over-
ride the starter kill. To do this, you must have the vehicle's igni-
tion key and know where the Valet button is located. Be sure to
check with your installer at the time of installation for the loca-
tion of the Valet button.
To override the starter kill, turn
the ignition to the On position.
Press the Valet button once
within 10 seconds. The in-
vehicle in-vehicle status LED will stop flashing and the vehicle should
start. If it does not start you may have waited too long; turn the igni-
tion Off and On and try again.
Location of Valet Button_________________________________
The remote will indicate the starter kill disable notification with
2 beeps and 3 flashes of the Orange LED.
DRW-35
➜

16 © 2005 directed electronics—all rights reserved
panic mode
If you are threatened in or near your vehicle, you can attract
attention by triggering the system with your 2-way remote. Just
press for 3-seconds, and you will enter Panic Mode. The
horn will honk (if connected) and the parking lights (if
connected) will flash for the programmed duration. To stop Panic
Mode at any time, press or on the 2-way remote.
The remote responds with one flash of the Red LED upon
entering Panic Mode and two flashes of the Red LED upon
exiting Panic Mode.
valet mode
You can prevent your system from automatically activating the
Failsafe®Starter Kill and locking the doors by using Valet Mode.
This is very useful when washing the vehicle or having it serviced.
In Valet Mode, the starter kill cannot be activated, even with the
2-way remote, but all convenience functions (door locks, remote
start, etc.) will continue to work normally.
To enter or exit Valet Mode:
1. Turn the ignition On.
2. Turn the ignition Off.
3. Press and release the Valet
button once within 10 seconds.
DRW-35
➜
nnoottee::In order for Panic Mode to be effective, the vehicle’s
horn (or optional siren) as well as the vehicle’s parking
lights must be connected.
➜

17
© 2005 directed electronics—all rights reserved
The in-vehicle status LED will light steadily if you are entering
Valet Mode, and it turn off if you are exiting Valet Mode.
The remote will respond with 3 Orange LED flashes on entering
and 2 beeps and 3 Orange LED flashes on exiting Valet Mode.
remote start
This feature allows you to remotely start and run your vehicle for
a programmable period of time. This makes it possible to warm
up the engine, as well as adjust the interior temperature of the ve-
hicle with the climate control system. If interior heating or
cooling is desired, the climate controls must be preset, and the
fan blower must be set to the desired level prior to remote starting
the vehicle.
To remote start the vehicle:
1. Press on the 2-way remote twice within 3 seconds.
2. The parking lights will flash to confirm that the vehicle will
attempt to start.
3. In gasoline vehicles, the engine will start 4 seconds after the
parking lights flash. In diesel vehicles, the engine will start
when the WAIT-TO-START indicator on the vehicle's dash
goes out.
iimmppoorrttaanntt!!(1) Never remote start your vehicle when the
keys are in the ignition, except when performing Valet®
Take-Over, and (2) Never start the vehicle if it is not in
either PARK or NEUTRAL.
➜