QANZ ZN-AIBOX-STD User manual
8
9
10
11
12
13
Front / Rear View
- REAR
MIC & SPEAKER AUDIO IN / OUT
Access Controler &
RF-Card Reader Devices
AUDIO
SD CARD type storages
ALARM IN
RS-485
WIEGAND
MZ09AU01_Rev00
The DC power jack uses only one of the front and rear sides.
Unused DC jack holes are blocked by the accessory's DC jack cover.
- FRONT
ZN-AIBOX-STDZN-AIBOX-STD
111 32
13
12
11
13
1 10 4 5 8
6 97
WIEGAND IN
WIEGAND OUT
Connect the Wiegand input sIgnal wires.
Connect the Wiegand output sIgnal wires.
Slot for inserting a micro SD card.
Connect the power plug of the provided 12V adapter.
Factory default.
DC jack cable clamp fixed hole.
1. Install AI Box on a network connected to the Internet and run a DHCP server.
2. Connect the network cable to the ETHERNET 1 port of AI BOX.
3. The AI Box boots up immediately when the adapter is powered on due there does not have separate power button.
4. It takes about 1 minute for connecting to the PC after the device completes booting.
Universal Serial Bus(USB) port for additional devices such as USB
Memory Stick.
RJ45 port for connecting IPCs and other devices through a separate
LAN.
Connect the sensor / alarm input signal wires.
Connect the remote control device for RS-485 communication.
Connect the audio line input and output.
IP Router
or Hub
Check The Video Stream Connection Setting
Multiple channels of video stream at once
Searching for setting ONVIF cameras
5.
①Enter the Channel Name
②Enter the RTSP URL of the camera.
③Select a transport protocol. The transport protocol specifies the protocol of the transport layer used to import
the video stream.
④Set the credentials needed for receiving the video stream.
Usually, the ID and password of the IP camera are used.
⑤If you want to use a camera speaker, check the ‘Use Camera Speaker’.
⑥Set the maximum video buffering time. If, due to network conditions or camera types, video information
is not transmitted smoothly and is received in a sudden burst, AI Box can redistribute it into smooth videos
according to the buffering setting. As the ‘Video Buffering’ setting is a maximum value, the actual buffering
will be less than the set value if there are no problems with the camera and network performance.
Click the channel for which you want to set the video in the list of video streams.
Set up multiple channels of video streams at once. You can set up multiple channels of video streams in bulk using
copy and paste, as well as features such as Apply to All.
To use the Bulk Setup feature, click the ‘Edit Video’ button in the Video Stream Settings area.
The ‘Batch Setting’ allows you to set the name, RTSP URL, transport, and authentication information for all channels at once.
The settings you enter in the Apply All line at the top can be applied to all channels by clicking the tick button for each setting.
Video clip guide (Refer to the on-line Technical document)
ONVIF is a standard for the interoperability of physical security devices. For network cameras that support the ONVIF
standard, you can set up video streams using Discovery. To use the discovery feature, click the ‘Search Cameras’.
Search for your camera in the ONVIF search pop-up, then enter your credentials to see a list of video streams supported by your camera. Assign the streams you wish to
analyze to a channel on the AI Box.
You can check that the video stream you have set up is being received correctly.
To check the receiving video stream, click the ‘Video Preview’.
Video Stream For Each Channel Setting
00:00
00:19
2023-05-09 오후 04:31:04Print-AIB2-QG-ENG. 1
Video source setup
● When run for the first time, it shows a list of AI BOX connected to the network. In the ID / Password field, admin / 1234 is entered by default.
●
When the AI BOX is in “factory default or factory reset” status, “1234” is set as a temporary password for network settings in the tool
● If the AI Box is not shown, please check the network cable is connected to ETHERNET 1 properly.
1. Click the device that wants to change the network
settings from the list.
2. Enter the network information to set in the Setup
Network section below.
3. Enter the ID / Password of the device.
- If the AI Box is in “factory default or factory reset”,
enter admin / 1234.
4. Click the Apply button.
Download and install the Device Management Tool from the link below.(www.ganzsecurity.com)
AI BOX is possible to search the device’s IP and set the network via the Device Management Tool program
DeviceManagementTool
When the install file runs, the firewall setting window will appear as below. For smoothly using, it is recommended
to allow the entire network.
Search for devices on the network
Setting screen
Running screen
Accessing to Device and setting the remote support settings
Download the Device Management Tool
To enable the AI Box to receive and analyze video from a camera, you must first set up the camera’s connecting information.
Click the ‘Video Stream’ in the sidebar navigation menu displays the settings menu for receiving video from the camera.
①The ‘AI Engine Resource’ displays usage relative to maximum AI processing capability.
Each app requires a different AI processing capacity, so be careful not to set over the maximum processing.
The ‘Video Decoding Resource’ shows current usage based on the maximum amount of video the AI Box can receive and process from the camera.
The ‘Video Resolution Resource’ shows the usage against the maximum resolution available on the AI Box. No item will exceed the limit.
②The ‘Video Stream’ settings allows you to set the video stream information accessible over the network.
Camera Video Input Setting
Screen after settings applied
1. After a while by pressing the Apply button,
the network setting of the device will be updated
in the list.
- If the network settings have not been changed,
it is due ID or Password being incorrect,
please check again.
2. After setting the network, double-click the device
information in the list to access the AI BOX.
- The AI Box webpage will open in the default
browser in Windows
(Recommended Web Browsers:
Google Chrome, Firefox and IE edge)
Enable the Remote Assistance function in the Setup > System Management > Technical Support menu.
You can receive remote technical support by sharing the Mac Address and Remote Code displayed on the UI.
- When accessing the AI Box for the first time, the initial password setting
UI is displayed. Set the password want to use.
- The password can use the alphabet, numbers, and special characters,
and it should be set to 8 to 16 characters.
- Log in using the device’s account information using admin as the ID and
the password set in the previous step.
Initial access and remote support settings
Initial password setting of Device
Remote support Settings
2023-05-09 오후 04:31:04Print-AIB2-QG-ENG. 2
