Qazqa New York WL Dark Grey User manual

100°
Fig.1(A) Detection Range
2M
2.0 M
8M
5M
F ig .1 (B ) O K F ig .1 (C ) N O T G O O D
Fig. 1(D)
Wall
Roof
North
New York WL Dark Grey
92303
INSTRUCTION MANUAL
Unchangeable LED
Max.4x0.5W LED
3000K±300K
10000H
3 x 1.2V AA
900mAh
Ni-MH
Rechargeable
battery
III
IP44
INTRODUCTION
The L antern Light has a build-in PIR
(Passive Infra Red) sensing device which
continuously scans a preset zone and
automatically switches the light on when it
detects movement in that area. Once
movement is detected within the range of
the sensor the light will switch on
automatically to illuminate pathways,
steps, patios, porches, or whatever area
you have selected to light for reasons of
safety, convenience or security. While
there is movement within range of the unit
the light will remain on.
During the day, the solar panel converts
sunlight into electricity to recharge the
batteries for LED light. This Lantern Light
has an adjustable TIME dial that allows
light duration of up to 90 seconds. When
the batteries are fully charged, it is
estimated that LED can work up to max. 60
times when TIME be set to 1.5 minutes,
totally 1.5 hours.
This unit includes 3 x 1.2V AA 900mAh
Ni-MH Rechargeable battery batteries,
which need to be replaced after 2-years
use, because the charging ability will
decrease.
HAVE YOUR SENSOR WORKED
WELL
To have sensor worked well, we suggest
you take the following points into account:
►
►
►
■Ideally the Lantern Light should be mounted
1.8 to 2.5 meters (6 to 8ft) above the area to be
scanned (refer to Fig.1A).
■To avoid damage to unit, do not aim the sensor
towards the sun.
■To avoid nuisance triggering, the sensor should
be directed away from heat sources such as
barbecues, Air-conditioners, other outside lighting,
moving cars and flue vents.
■To avoid nuisance triggering, keeping away from
the area of strong electromagnetic disturbance.
■Do not aim towards reflective surfaces such as
smooth white walls, swimming pools, etc...
■The sensor scanning specifications (approx. 6
meters at 100°-- round) may vary slightly depending
on the mounting height and location. The detection
range of the unit may also alter with temperature
change. Before selecting a place to install your lantern
light you should note that movement across the scan
area is more effective than movement directly toward
or away from the sensor (refer Fig.1B). If movement is
made walking directly towards or away from the
sensor and not across, the apparent detection range
will be substantially reduced. (refer to Fig. 1C)
CHOOSE LOCATION FOR YOUR LIGHT
■This light’s power comes
from sunlight. For max sun
exposure and longer light
output, place the solar
panel, connecting to the
light, in a position that
receives at least 4-6 hours
direct sunlight per day.
（refer to Fig. 1D）Ideally,
the solar panel should be
adjusted to the angle facing
the sun. Placing the solar
panel in a shaded location
will not allow the batteries to be charged fully. It will
reduce the number of hours the light operates per
night.
■This Solar Light is ideal for areas where electricity
is not available, including driveways, garages,
entrance doors, backyard sheds and other remote
areas, for safety and convenience around your home.
222.2 mm
177.1mm
374.4 mm
161.1 mm
127mm 120.3 mm
Fig.2(A)

■The sensor has a build-in photocell which making
the light only works from dust to dawn. In choosing a
location for your light, ensure that the sensor is not
placed near night time light sources such as porch
lighting or sheet lighting which will affect the photocell.
INSTALL THE LIGHT AND SOLAR PANNEL
1. Re-fix the lantern lid as Fig-2(A) shown and screw it
on the lantern’s main body by 2 lid screws.
2. Mount the solar panel and lantern light’s wiring box
on the position chosen as advices above by the anchors
and screws included in this package. (refer to Fig. 2B)
3.Fix the lantern body onto the wiring box by fixing
nuts.
►
NOTE: DO NOT INVERT THE LANTERN.
4. Connect the solar panel to your light by plugging
the 2 power cords together with the plug and socket in
a tight connection.
BEFORE USE FOR THE FIRST TIME
■Ensure the power switch in wiring box of your light
is at the OFF position. In this position the solar cell will
charge the batteries without activating the light.
■ Leave the switch “off” for up to 2 days and make
sure the solar panel is placed in direct sunlight before
the first use. This gives the batteries in your Solar Light
has a full-charge for motion sensor adjustment and
normal operation. It is good for the batteries.
■After the initial full-changing, shift the switch to
“ON” position. Now, your light is ready for serve.
UNDERSTAND THE CONTROLS
ADJUSTING THE DURATION TIME: The length light-on
time after activation can be adjusted from (10±5)
seconds to (90±15) seconds. Rotating the TIME knob
+ to - will reduce the duration time.
Note: Once the light has been triggered by the PIR
sensor any subsequent detection will renew the timed
period again from the beginning.
Adjusting the lux control level: The Lux control
module has a built-in sensing device (photocell) that
detects daylight and darkness. The ( ) position
denotes that load can work at day and night, and the
( ) position only work at night. You can set to operate
the unit at the desired level by adjusting the LUX knob.
Lantern Lid
Wall Mount
Screw (x 3)
Power cable
Gasket Rubber
Wireing Box
Fixing Nut (x 2)
Fig.2(B)
Fixing Screws (x 2)
Lantern Body
Transparent lens
Lid Screw (x 2)
TIME
+
-
Angle adjustment
support
Plug
Solar pannel
3 Screws and anchors for solar
pannel mounting bracket
Solar pannel
mounting bracket
Gasket
Rubber
Sensor
Switch
Adjusting knobs
LUX
►
►
►
►
Fig.3
REPLACE THE RECHARGEABLE BATTERIES
（refer to Fig. 3）
After 2 years, the charging ability of the batteries
decrease, they may be replaced by AA NIMH 1.2V
900mAh rechargeable batteries. Follow the
replacing steps in Fig.3’:
1. Remove the lantern lid by unscrew the lid screws.
2. Remove the battery plate.
3. Replace the batteries with right electrode
direction
4. Re-fix the battery plate and lantern lid back onto
their positions.
GENERAL ELECTICAL AND SAFETY WARING
1. Do not cut the power cord. Stop use if the wire
becomes frayed or broken.
2. Do not immerse the Solar Light or solar panel in
liquid.
3. Do not use any other solar panel other than the
one provided with this unit. This may result in injury
or damage to the light and with no warranty.
4. Position the power cord fastened and not moving
around or result in another hazard (such as tripping)
TECHNICAL SPECS:
Battery: 3x1.2V 900mAh AA NIMH Battery
Wattage: Max.4x0.5 Watt LED
Detection range: 100º (round) and Max. 6 meters
Duration time: 10±5 sec. to 90±15sec.adjustable
Weatherproof: IP44
NOTE: When your light comes to the end of its life
or you are to replace it. Please do not simply
dispose it with your normal household waste. Check
with your retailer or local authority for suitable
options.
New regulations encourage the recycling of Waste
from Electrical and Electronic Equipment (European
“WEEE Directive” effective August 2005).
Do not dispose of batteries in general household
trash or into a fire since the batteries may explode.
Consult your local regulations for correct disposal of
batteries. Do not take apart the batteries since they
contain corrosive chemicals.