Qbex Slim Pad User manual

Chapter 1: Brief Introduction
1.1 Product Overview
USB connector
OTG connector
Camera
Volume-
Menu Button
Volume+
Power button
Option Menu
Power connector
TF card reader MIC
Earphone
Escape
Speaker
- 1 -

- 2 -
1.2 Buttons & Connectors
Name Function
Power button Press for a long time to power on/off;
Press for a short time to lock the screen or wake
up the screen
Volume + Press to increase the volume
Volume - Press to decrease the volume
Escape Escape: Press to return to upper menu
Option Menu Option Menu: Press to view optional menu items
of application
Main menu Press to return to desktop; Press for a short time
also to pop up relative menu
Speaker Speaker output
MIC Microphone for sound recording
Earphone 3.5’’ earphone connector
Power connector 2.5 mm DC5V/2A battery charging connector
TF card reader External TF card slot
OTG OTG connector to external USB
Disk/Mouse/Keyboard/LAN/3G Dongle
USB USB connector to computer (PC or Notebook)

Chapter 2: Preparation before using the
product
2.1 How to power on the device
The device will automatically power off when connected with power adapter.
When the device is off, press Power Button for 3 seconds long for system to
enter Android Start-up Status Bar. It takes about 30 seconds for the desktop to
show up.
The screen is on Lock status. User needs to hold ‘lock’ icon upwards to the
green point for the device to ‘unlock’ automatically as the following photo shows:
Green Point
Hold ‘lock’ icon upwards to the
green point to ‘unlock’ the screen
Connect the device with PC, system will start automatically (only to power the
device, not to charge it).
- 3 -

- 4 -
Power Saving Mode and Screen Lock: Press Power button slightly after
system starting-up to enter Sleep power-saving mode. Press Power button again
and to light the screen in 1 second.
Notice:
In power-saving mode the previous operations are still valid and will continue,
e.g. music or video is still playing but the screen is black.
2.2 How to power off the device
When the device is on, press Power button for 3 seconds long for Power off
Confirmation Interface to show up. The system will power off automatically after
you confirm to power off.
The device will give off warning beeps when battery is low and power off
automatically if it is not charged. If the device fails to boot up, please charge it for
5 minutes before starting it up again.
2.3 How to connect the device to PC or Notebook
Start up the computer and connect the device to PC with specialized USB cable
to realize data transmission between the device and PC. Open the device as a
USB storage device and you can copy or delete the files of the device on the PC.
Notice: Files of the device are not allowed to be opened or played when the
device is connected to PC. The company is not responsible for abnormal
performance of the device or PC resulted from such operations.

- 5 -
2.4 How to use TF card
User will find two removable disks after connecting the device to PC. The first
one being the memory card of expansion slot and the latter being internal
memory disk of the device. User can not access to the first disk if no memory
disk is inserted in card reader.
Notice:
The device only support TF card (up to 32GB at most).
Please disconnect the device from computer before uninstalling
TF card.
How to insert/remove the expansion card
a) To insert TF card: Place the device with the screen side up. Push the TF
card (the side with metal contacting pins downwards) into the card reader
slot. The device can read files inside the TF card only under such
condition.
b) To remove TF card: Push the card inside slightly and the card will spring
back. Pick out the card.
2.5 Battery Management and Charge
Charge the battery for 8~12 hours to ensure enough power at the first
time you are using the device.
Connect the micro part of power adapter to DC power-in connector of
the device and the other end to power supply connector. Battery icon will
scroll on desktop to indicate the device is in charging status. Please wait until
the device is fully charged before unplugging charger. Charging LED indictor
will turn light blue when charging process is completed. The battery icon will
stay still on desktop as well.

Notice:
Please contact your local dealer for specialized charger (5V-2A
output).
9V charge is not allowed to charge the device. The company is
irresponsible for damage caused to device by using 9V charger.
11 14
2.6 User’s Interface
- 6 -
1
2 3
4
5
9
10
12
13
15
17
16
18

- 7 -
7
8 6
Notice:
Some function logo only appears when application is enabled.
User’s Interface may look different if you rearrange the icons.

2.7 Function List
No. Icon & Function
1
Click to return to home page
2
System is downloading item
3
Ethernet Connection is off
4
3G network is on
5
3G signal strength
6
3G network is off
7
Ethernet Connection is on
8
WIFI signal strength
9
Battery icon to show remaining battery power
- 8 -

10
Alarm clock is set
11
To decrease volume
12
To increase volume
13
Escape icon to return to previous page
14
Settings
15 Google Engine
16
Music play bar
17
Function module menu
18
To switch from desktops
- 9 -

2.8 Language & Keyboard Settings
Click ‘Menu’ icon to enter function menu, or click ‘Settings’ icon
upon desktop, then click ‘Settings’→‘Language & keyboard’ →‘Select
language’ to find and select device interface language.
Click ‘Setting’ to enter Settings page.
- 10 -

Click ‘Language & keyboard’.
Find and click ‘Language & keyboard’ on ‘Settings’ menu.
Click ‘Select language’.
- 11 -

User can pull up or pull down to view available language options and click to
select specific language for device user interface language.
- 12 -

- 13 -
Chapter 3: Hardware Configuration
Hardware Specification
Processor Rockchip RK2918 Cortex A8 1.2GHz
Hardware Decoding 1080P video decoding for H.264, VP8, RV, WMV,
AVS, H.263, MPEG 4 etc.
Memory DDR3 512MB
Hard Disk 4GB/ 8GB NAND Flash (OPTION)
Display 7'' 800×600 resolution (aspect ratio 4:3 ),
Capacitive touch panel, 5 point Multi Touch
OS Google Android 2.3
Camera VGA 640x480 resolution
Speaker D class embedded Speaker
I/O Port USB 2.0 x1 ,OTG x1, Micro SD support 32GB
Micro SD (TF), Earphone jack
Communication
Wi-Fi 802.11 b/g/n, Bluetooth 2.1+ EDR, Support
3G Dongle (WCDMA, EVDO，TD)
Power Battery 4,000mAh 3.7V, Charger 100~240VAC
5V/2A

- 14 -
Features
Mobile Storage Can be used as USB Storage
OTG Support USB mouse, Keyboard, Pen driver, 3G dongle,
USBLAN
Audio Format MP3, WAV, WMA, OGG, FLAC, AAC, 3GPP, APE
Video Format
1080P Decoding，YouTube 720P Decoding, HTML5,
Flash 10.2，AVI, WMV, MP4, M4V, RV, RMVB, VP8,
MKV, VOB, FLV, DAT, 3GP
Picture Format JPG, BMP, PNG, GIF
3D Accelerator
2D/3D Graphic processor, support OpenGL ES 2.0 &
Open VG
G-Sensor Support 3D game, Picture, eBook
Other Features
Browser, Internet Chat, Email, eBook, Resource
management
Clock, Alarm, Calculator, Recorder, Android Market
Recorder Embedded Mic.
Battery Time Audio Playback: 10Hr , Video Playback: 4.5~5Hr, Web
Browsing: 7Hr
Dimension 185.2 Lx 144.5 W x 12.8 H mm
Weight 432 g

Capitulo 1: Introducción Breve
1.1 Vista General
Conector USB
- 15-
Conector OTG
Cámara
Volumen -
Boton Menu
Volumen +
Botón de
Encendido
Opci de Menúón
Conector de Poder
Escape
Lector de Tar
j
eta Parlante
MIC
Audífono

- 16 -
1.2 Botones y Conectores
Nombre Función
Botón de Encendido Presione por un largo tiempo para
encender/apagar
Presione por un corto tiempo para bloquear o
despertar la pantalla
Volumen + Presione para subir el volumen
Volumen - Presione para bajar el volumen
Escape Escape: Presione para volver al menú anterior
Menú de Opción Menú de Opción: Presione para ver ítems
opcionales del menú
Menú Principal Presione para volver al escritorio; Presione por
un corto tiempo para que aparezca menú
familiar
Parlante Salida del Parlante
MIC Micrófono para la grabación de sonido
Audífono 3.5’’ conector de audífono
Conector de Poder 2.5mm DC5V/2A conector de carga para la
batería
Lector de Tarjeta TF Ranura externa para tarjeta TF
OTG Conector OTG para USB externo
Disco/Mouse/Teclado/LAN/3G Dongle
USB Conector USB a computador (PC o Portátil)

Capitulo 2: Preparación antes de usar el
producto
2.1 Como encender el dispositivo
Este dispositivo se apagara automáticamente cuando se conecte el cable de
poder.
Cuando el dispositivo este apagado, presione el Botón de Encendido por 3
segundos para iniciar el Barra de Estado de Android. Se demora
aproximadamente 30 segundos para el escritorio en aparecer. La pantalla esta
Bloqueada. Presionar y mover el icono del ‘candado’ hacia arriba hasta el punto
verde para que desbloquear el dispositivo así como muestra la siguiente
imagen:
Green Point
Hold ‘lock’ icon upwards to the
green point to ‘unlock’ the screen
Connect the device with PC, system will start automatically (only to power the
device, not to charge it).
- 17 -

- 18 -
Modo de Ahorro de Energía y Bloqueo de Pantalla: Presione levemente el
Botón de Encender para iniciar el Modo de Ahorro de Energía. Presione el
Botón de Encender de nuevo para iluminar la pantalla.
Aviso: En el Modo de Ahorro de Energía, las operaciones anteriores aun son
validas y continuaran (Ej. Música y videos aun se reproducen pero la pantalla
esta negra)
2.2 Como Apagar el dispositivo
Cuando el dispositivo esta encendido, presione el Botón de Encendido por 3
segundos para que la Confirmación de Apagar aparezca. El sistema se apagara
automáticamente después de confirmar el apagado.
El dispositivo emitirá sonidos de advertencia cuando la batería esta baja y se
apagara automáticamente si no se carga. Si el dispositivo no arranca, por favor
cargarlo por 5 minutos antes de iniciarlo de nuevo.
2.3 Como conectar el dispositivo a una PC
Encender el computador y conectar el dispositivo al PC con el conector de USB
para realizar transmisión de datos entre el dispositivo y PC. Abrir el dispositivo
como un dispositivo de almacenaje USB y se puede copiar o borrar archivos del
dispositivo al PC.
Aviso: No se permite abrir y/o usar archivos en el dispositivo mientras este
conectado al PC. QBEX no se responsabilizara por rendimiento anormal del PC
o dispositivo por estas operaciones.