Qbus QWE RC01/pulse User manual
Technical product data sheet
Qbus Wireless 1-button remote control (QWE RC01/pulse)
©QBUS NV, Joseph Cardijnstraat 19, B-9420 Erpe-Mere, Belgium 1/2
Technical product data sheet, Feb 2019
FVL/QWE-RC01_PULSE_NL
1. Product description
The QWE RC01/pulse is a 1-button remote control. Pressing the
button transmits a wireless telegram, which is picked up by the
QWI/EW. If you configure this in System Manager III, then this
control can perform an action on another wireless module and/or on a
bus-controlled module.
The QWE RC01/pulse has a built-in battery. When the battery
capacity is low, the indicator LED will flash when operated.
2. Commissioning
The QWE RC01/pulse has a built-in battery as standard and so is ready
for connecting to a QWI/EW with System Manager III.
Follow the instructions given in System Manager III to connect it to
the QWI/EW module.
3. Check battery
The module verifies the battery voltage:
-One of the keys is pressed
-At least once every 24 hours after sending the latest status.
As soon as the battery status is found to be weak, a ‘Battery Low’ signal
is transmitted at least once every four hours.
Once the battery is empty, the red LED will blink briefly three times
at 20-second intervals and the voltage-too-low telegram will be
transmitted automatically. It is recommended to replace the battery
now. (See ‘Replacing the battery’)
If the voltage drops further, the module will switch itself off and no
more status changes will be transmitted.
4. Replacing the battery
1. Insert a small object (e.g.: a slotted screwdriver or a coin)
into the slot at the top of the transmitter and open the
housing.
2. Replace the battery. Only use battery type CR2032.
Attention: Make sure that the positive pole is visible at the
top. Keep batteries away from children.
3. Close the housing.
Please note: The module retains its link with the QWI/EW, you don’t
need to take more steps for this.
5. Solving problems
If the receiver fails to respond to this module:
-Check the battery status.
-Check that the wireless connection in the installation
between this module and the QWI/EW is not disrupted.
-Check the configuration of the QWI/EW and whether the
link with this module is still active.
-Check that other wireless devices with the same frequency,
or that work at almost the same frequency, are not
disrupting this product's operation.
If the LED does not light up:
-Replace the battery. (Ensure correct battery polarity.)
6. Safety rules
Read the entire manual before installing the module and activating the
system.
WARNING
______________________________________________________
•The device must be mounted and commissioned by an
authorised electrician in accordance with the country-specific
regulations.
•The device complies with the IP54 standard, which means
that it is protected against limited dust penetration and is
protected against low-pressure water jets in all directions.
•The device may not be opened, except as described for
replacing the battery. The guarantee provisions will be void if
the module has been opened.
•Keep batteries away from children.
Technical product data sheet
Qbus Wireless 1-button remote control (QWE RC01/pulse)
©QBUS NV, Joseph Cardijnstraat 19, B-9420 Erpe-Mere, Belgium 2/2
Technical product data sheet, Feb 2019
FVL/QWE-RC01_PULSE_NL
7. Technical data
General specifications
•Power supply: 1x 3V battery, CR2032
•Radiated power: 0.14 mW
•Modulation coding: FSK
•Wireless protocol: EasyWave:
•Range: free field: 150 m; buildings: 30 m
•Ambient temperature: -20°C to 60°C
•Maximum humidity: 93%, no condensation
•Maximum installation height: 2,000 metres
Physical specifications
•Protection grade: IP54
•Transmitter dimensions: 55 mm x 36.5 mm x 16 mm
•Transmitter weight: approx. 17.0 g
CE marking
•In accordance with EMC and low voltage regulations. The
module corresponds with EN 61000-4-2 and 50090-2.
8. Guarantee provisions
Period of guarantee: Two years from date of delivery. The guarantee
does not apply if the module is opened!
Any faulty modules should be sent postage-free with a description of
the defect to our customer service:
QBUS N.V.
Joseph Cardijnstraat 19
9420 Erpe-Mere
Belgium
