QED Systemline User manual

SystemlineUSER GUIDE
ZINS519
SystemlineUSER GUIDE
QED Audio Products Ltd,
Ridgeway House, Ridgeway Close,
Lightwater, Surrey GU18 5XU
Tel: [phone]
Fax: [phone]
Email:[email protected]
Internet:http://www.qed.co.uk

CONTENTS PAGE
Component Overview 1
KMS in Detail 2
DMS in Detail 3-4
RHS in Detail 5
How to use this guide
BecauseSystemlineoffersmanyvariationsthisguidehastickboxestoshowwhich
variationisapplicabletoyourinstallation.Your installer will fill these in for you.
INSTALLATION DETAILS
Systemline Controller Serial Number: ___________________________________
Installer details:
Installer contact name: _______________________________________________
Installer contact tel no: _______________________________________________
Source Equipment Details:
Source1: _______________________________________________
Source2: _______________________________________________
Source3: _______________________________________________
Source4: _______________________________________________
USER GUIDE 5
RHS
INSTALLED?
√
Select and Play CD Stop CD Skip up track Skip down track
Select Random Play Skip up disc
Select and Play Tape Stop Tape Wind reverse Wind forward
Select Satellite receiver Down one channel Up one channel
Select and Play Video Stop Tape Wind reverse Wind forward
Pause Tape Down one channel Up one channel
Select and Play CD2 Stop CD Skip up track Skip down track
No function Select Random Play Skip up disc
Select Tuner2 Returns to favourite station Move up one Pre-set station Move down one Pre-set station
No function No function No function
Select Tuner Returns to favourite station Move up one Pre-set station Move down one Pre-set station
√
If Mini Disc is installed, Random and Disc Skip will have no function
Select and Play DVD Stop DVD Scan reverse Scan forward
Pause DVD Track back Track forward
INSTALLED?
√

Systemline USER GUIDE
KMS - Source Selection &Volume
*ENGAGED display is a courtesy notice to indicate that the source chosen
is being played in another zone already. It is still possible to change the
source but it may effect the listening pleasure of another zone.
Volume is displayed from 0-63 (0=OFF). ie Vol 34
Time is displayed whilst system is in Stand-by. ie 13:21
(()) indicates that the paging has been activated
Mute indicates volume at zero (zone is still ON)
Stby indicates Stand-by mode (zone is OFF), this display is then followed
by the time display. ie 13:21
Source Selection Keys
Press one of these
buttons to get sound
Volume
+ Increase volume
- Decrease volume
DMS
KMS - Source Control Options NORMAL ENGAGED*
SOURCE 1 Tunr tunr
SOURCE 2 Cdcd
SOURCE 3 Tape tape
or Sat sat
SOURCE 4 Dvd dvd
or Tun2 tun2
or Vcr vcr
or Cd2 cd2
TUNER Pre-set down Pre-set up Pre-set 1
CD Track up Track down Stop Disc up
MD Track up Track down Stop
TAPE Back wind Forward wind Stop
SATELLITE Channel up Channel down
VCR Back wind Forward wind Stop Pause
DVD Track up Track down Stop
TUNER2 Pre-set down Pre-set up Pre-set 1
CD2 Track up Track down Stop Disc up
Source
Control <>
INSTALLED?
√
INSTALLED?
√
√
USER GUIDE 2USER GUIDE 3
Mute speakers
Stand-by (zone only)
5 second push = Power down (OFF)
2
2

SYSTEM OVERVIEW
Your Systemline installation will include some, if not all, of the following items:
To program alarm or change time* (assuming DMS is in Stand-by mode)
If a zone splitter is installed within a zone to allow you to switch between a 2nd set of speakers
in a different room there will be an illuminated LED below the one or both of the two buttons
marked "A" and "B".
The illuminated LED indicates that the speakers are active. It is possible to have pair "A" active
or pair "B" active or both. Note it is not possible to turn both pairs OFF so if you wish to switch
from pair "A" to pair "B" you must first activate pair "B" before being able to deactivate pair "A".
SystemlineUSER GUIDE
Systemline Controller S4.3
Nerve centre of the system.The
Controller should be left switched
on permanently, and once set up
by your installer it should need
no further adjustment.
Display Module (DMS)
Displays information about the
status of Systemline and also
receives commands from RHS
Remote Handset (RHS)
Issues commands to select
and control sources from the
comfort of your armchair.
Keypad Module (KMS)
Used to select source and issue
commands to that source.
USER GUIDE 1
USER GUIDE 4
Prime Zone (A)
Selected (B) Sub Zone
Selected
*Clocks on dms displays will synchronise with the clock on zone a dms at 12:00
Press
Alarm button
Press
Alarm button
Press
Alarm button
Press
Alarm button
Press
Alarm button
Alarm ON
Advances
hours
Use Tuner
Advances
hours
Alarm OFF
Advances
minutes
Use CD
Advances
minutes
Enters alarm On/Off mode
Enters alarm setting mode
Enters source selection mode
Enters clock setting mode
Exits set up mode
DISPLAY BUTTON A BUTTON B