Qlightec ST45L-USB User manual

PB 1
USB LED Tower Lights
Please scan the QR code for more
detailed product information.
www.qlight.com
Ordering Specication
Thank you for purchasing Qlight’s products. Please read this user manual carefully
prior to installation and operation to ensure safe and correct use.
Precautions for Safety
Failure to follow the instructions below may cause a loss of life or serious physical injury.
1. Please remove any objects that can interrupt ventilation around the product.
2. Please turn o󰀨 the power of the product immediately if it fails to operate properly.
3. Carefully wire the product according to each product’s specication.
4. Please be careful in preventing chemicals such as thinner, benzene, etc. in contact with the surface of the product.
5. Do not apply excessive force/impact to the product.
6. Failure to follow any of the instructions above may cause malfunction or damage to the product, re, and electric shock.
Precautions for Correct Use
Failure to follow the proper instructions may cause damage to property, the product, and or malfunction of the
product that would void the warranty.
1. During wiring or maintenance, please completely turn o󰀨 the power of the product. (Failure to follow this may lead to an electric shock.)
2. Do not install the product in locations that subjects it to excessive dust or water other than the conditions designated by the IP protection
ratings indicated for each product. (Failure to follow these instructions may cause a re to the product, electric shock, physical injury,
malfunction or damage to the product.)
3. Do not alter or repair this product. If maintenance or repair service is required, please contact your local Qlight contact point. (Failure to
follow these instructions may lead to re, electric shock, or product damage.)
4. Please apply the correct voltage to the product. (Failure to follow these instructions may lead to re, electric shock, or product damage.)
5. When the product is applied to a condition that may impact lives or property, please make sure to have a double safety device. (Failure to
follow this may cause damage to property, re, electric shock and loss of life.)
ST45(M)L/ ST56(M)EL/ ST80(M)EL-USB
5030
23
90dB85dB
ST56L-USB-BZ
-3-RAG -LW18
[Model number] [Layer] [Color]
[Mount bracket]
| | | |
• ST56EL-USB-BZ
• ST56EL-USB-WS
• ST56EL-USB-WM
• ST56EL-USB-WA
• ST56MEL-USB-BZ
• ST56MEL-USB-WS
• ST56MEL-USB-WM
• ST56MEL-USB-WA
• Layer 1-1
• Layer 2-2
• Layer 3-3
• Layer 4-4
• Layer 5-5
R-Red
A-Amber
G-Green
B-Blue
W-White
• (Blank)
- Standard type
• Mounting type
- LB18 - LW18
- QZ18 - SZ18
- QL18 - SL18
- QLA18
ST80EL-USB-BZ
-3-RAG -LW24
[Model number] [Layer] [Color]
[Mount bracket]
| | | |
• ST80EL-USB-BZ
• ST80EL-USB-WS
• ST80EL-USB-WM
• ST80EL-USB-WA
• ST80MEL-USB-BZ
• ST80MEL-USB-WS
• ST80MEL-USB-WM
• ST80MEL-USB-WA
• Layer 1-1
• Layer 2-2
• Layer 3-3
• Layer 4-4
• Layer 5-5
R-Red
A-Amber
G-Green
B-Blue
W-White
• (Blank)
- Standard type
• Mounting type
- LB24 - LW24
- QZ24 - SZ24
- QL24 - SL24
- QLA24
• ST56(M)EL-USB • ST45(M)L-USB
• ST80(M)EL-USB
ST45L-USB-BZ
-3-RAG -LW18
[Model number] [Layer] [Color]
[Mount bracket]
| | | |
• ST45L-USB-BZ
• ST45L-USB-WS
• ST45L-USB-WM
• ST45L-USB-WA
• ST45ML-USB-BZ
• ST45ML-USB-WS
• ST45ML-USB-WM
• ST45ML-USB-WA
• Layer 1-1
• Layer 2-2
• Layer 3-3
• Layer 4-4
• Layer 5-5
R-Red
A-Amber
G-Green
B-Blue
W-White
• (Blank)
- Standard type
• Mounting type
- LB18 - LW18
- QZ18 - SZ18
- QL18 - SL18
- QLA18

2 3
Product Specications
Model number Layer Certicate Color
ST45L-USB-BZ
ST45L-USB-WS
ST45L-USB-WM
ST45L-USB-WA
ST45ML-USB-BZ
ST45ML-USB-WS
ST45ML-USB-WM
ST45ML-USB-WA
5 Buzzer sounds
5 Warning sounds
5 Melodies
5 Alarms
1
-
R-Red
2
R-Red
G-Green
3
R-Red
A-Amber
G-Green
4
R-Red
A-Amber
G-Green
B-Blue
5
R-Red
A-Amber
G-Green
B-Blue
W-White
Model number Layer Certicate Color
ST80EL-USB-BZ
ST80EL-USB-WS
ST80EL-USB-WM
ST80EL-USB-WA
ST80MEL-USB-BZ
ST80MEL-USB-WS
ST80MEL-USB-WM
ST80MEL-USB-WA
5 Buzzer sounds
5 Warning sounds
5 Melodies
5 Alarms
1
-
R-Red
2
R-Red
G-Green
3
R-Red
A-Amber
G-Green
4
R-Red
A-Amber
G-Green
B-Blue
5
R-Red
A-Amber
G-Green
B-Blue
W-White
• Protection rating : IP23
• Ambient operating temperature : -30°C to + 50°C
Model number Layer Certicate Color
ST56EL-USB-BZ
ST56EL-USB-WS
ST56EL-USB-WM
ST56EL-USB-WA
ST56MEL-USB-BZ
ST56MEL-USB-WS
ST56MEL-USB-WM
ST56MEL-USB-WA
5 Buzzer sounds
5 Warning sounds
5 Melodies
5 Alarms
1
R-Red
2
R-Red
G-Green
3
R-Red
A-Amber
G-Green
4
R-Red
A-Amber
G-Green
B-Blue
5
R-Red
A-Amber
G-Green
B-Blue
W-White
• ST56(M)EL-USB • ST45(M)L-USB
• ST80(M)EL-USB

2 3
Dimensions
(Units : mm)
LAYER
1
2
3
4
5
L
198
238
278
318
358
LAYER
1
2
3
4
5
L
412
452
492
532
572
PCD 30
360˚/3-M4 BOLT
Ø8 CABLE ENTRY
M1 81.5
THREAD
L
Ø18
Ø45
840
Ø45
840
L
150
20 026 138
USB CONNECTOR
USB POWER CONNECTOR
USB CONNECTOR
USB POWER CONNECTOR
12
LAYER
1
2
3
4
5
L
230
270
310
350
390
LAYER
1
2
3
4
5
L
367
407
447
487
527
Ø80
1240
L
178
USB CONNECTOR
PCD 50
360˚/3-M4 BOLT
Ø8 CABLE ENTRY
L
120 35 160 40 12
Ø80
USB CONNECTOR
USB POWER CONNECTOR
Ø24
M18Ⱌ1.5
THREAD
12
LAYER
1
2
3
4
5
L
192
232
272
312
352
LAYER
1
2
3
4
5
L
406
446
486
526
566
PCD 40
360˚/3-M4 BOLT
Ø8 CABLE ENTRY
Ø56
L
40 10142
USB CONNECTOR
USB POWER
CONNECTOR
USB POWER
CONNECTOR
Ø18
Ø56
L
40 10130200 26
USB CONNECTOR
USB POWER CONNECTOR M18Ⱌ1.5
THREAD
12
ST56MEL-USB
ST80EL-USB
ST56EL-USB
ST80MEL-USB
ST45L-USBST45ML-USB

4 5
• Connect both USB power connector and USB signal control
connector that are connected to each other to USB ports of a PC.
• Product does not run in case of USB power connector connection only.
USB CONNECTOR
USB POWER CONNECTOR
1. Please connect USB Tower Lamp and PC as above gure <How to connect with PC>
2. Please download test program(USB.zip) from Qlight website or blog.qlight.com
3. The downloaded sample program will be saved as “USB Test Program.zip”.
When you unzip the le, there will be a le with the names below.
Test program Required library for test program
※
When developing the program, please download and refer to the le “manual and library”(sample programs and manuals
for developers).
4. When you run the “QLight lamptest_usb.exe”le, a test programs will show up as above.
Products sound options are classied as WS / WA / WM / BZ. The product will only play the sound option selected when
the order was placed.
① Lamp Control ② Sound Selection ④ Index
③ Sound Group Selection
USB Cable Wiring Instructions
Test Instructions
<For Connecting Method with pc> <Test program>
■ How to use program
Article Detailed specication
① Lamp control
- ON: Lamp turns on when the button is clicked
- ON/OFF: Lamp ashes when the button is clicked
- OFF: Lamp turns o󰀨 when the button is clicked
② Sound selection
- 1ch-5ch: Has 5 sounds per model, turns on the chosen sound
- Click “Sound o󰀨” button to turn o󰀨 the sound
③ Sound group selection
- WS : 5 warning sounds(mono)
- WP : 5 special warning sounds(mono)
- WM(1) : 5 Melodies(mono)
- WA(1) : 5 alarms(mono)
- WB : Software Buzzer 5 sounds(speaker type)
- Buzzer : 5 Buzzer sounds
- WM(8) : 5 Melodies(8 chord)
- WA(8) : 5 alarms(8 chord)
④ Index - You can connect up to a maximum of 4 USB Tower lights per PC
- Must be controlled by selecting Index0 - Index3 for controlling the USB tower light. The default is set to Index0

4 5
Installation Environment and Protection Rating
• This product is designed for use with protection rating of IP23.
• If the product is installed in locations that subject it to excessive dust or water other than the designated IP protection rating
indicated(IP23), it may cause malfunction or damage to the product.
• For further information, please visit our website (www.qlight.com).
Parts Denition
USB CONNECTOR
USB CONNECTOR
USB POWER CONNECTOR
USB POWER CONNECTOR
Cover
(ABS)
Lens(AS)
Housing (ABS)
Pole(Al)
Buzzer hole
How to Change Lens Kit
• When rearranging or replacing the lens kits, please be aware of the
contact point ① and the connector pin ②marked in the diagram on
the left.
• Press down to assemble the lens kits while making sure that connecto r
pin ②and connector ③aligns correctly.
• Please make sure that the rubber spacer placed on the top of each
lens kit is tightly secured to the bottom of the other lens kit.
※Cautions
Lens modules are connected via the contact point of each module.
In case the contact point is damaged, it may cause contact failure.
②
③
①

6 7
Mounting Hole Specications
① Machine holes on the mounting surface referring to the diagram below.
② Remove the ange nuts from bolts and place the product through the mounting surface holes.
③ Fasten the ange nuts on the opposite side of the mounting surface until the product is tightened securely.
Mounting Accessories (Sold Separately)
• Please refer to the dimensions below for installation of mounting brackets
ST56MEL-USBST45ML-USB ST80MEL-USB
3-Ø5 HOLES
Ø12 CABLE ENTRY Ø12 CABLE ENTRY
3-Ø5 HOLES
PCD 50PCD 40
PCD 30
3-Ø5 HOLES
Ø12 CABLE ENTRY
Dimensions
ST45ML-USB
ST56MEL-USB
TWS45 TWA45
ST80MEL-USB
TWS80 TWA80
■ST45ML-USB/ ST56MEL-USB/ ST80MEL-USB -
Direct mounting Type Model

6 7
Dimensions
ST45L-USB
ST56EL-USB
18mm SCREW & NUT LB18
LW18 SZ18
QZ18 SL18
QL18 QLA18
■ S
T45L-USB/ S T56EL-USB - Pole Mounting Type Model
Ø18
Ø18
32
34 24
Ø70
51
M18x1.5
THREAD
75
52
69
Ø18
Ø18
66
52
38
34
46
50
58
Ø28
1/2" PF
4-Ø5 HOLES
12x22
CABLE ENTRY
Ø70
50
Ø18
4-Ø5 HOLES
PCD 56
60 57
4-Ø5.5 HOLES
Ø19 CABLE ENTRY
Ø18
Ø90
PCD 73
4-Ø5.5 HOLES
2-Ø8.5 HOLES
PCD 54~56
Ø90
Ø18
4-Ø6 HOLES
45.5 66
Ø11 CABLE ENTRY
PCD 73
Ø18
Ø70
51.5 67
4-Ø5.5 HOLES
Ø18 CABLE ENTRY
PCD 54~56

8
Dimensions
ST80EL-USB
24mm SCREW & NUT LB24
LW24 SZ24
QZ24 SL24
QL24 QLA24
■ ST80EL-USB - Pole Mounting Type Model
46
70
81
32
34
46
M24x1.5
THREAD
2-Ø8.5 HOLES
69.5
52
38
34
46
50
70
1/2" PF
4-Ø5 HOLES
12x22 CABLE ENTRY
33
Ø24
Ø70
55
4-Ø5.5 HOLES
PCD 54~56
Ø24
4-Ø5 HOLES
Ø90
55.5
PCD 73
Ø24
Ø35
Ø24
Ø24
60 57
Ø90
Ø19 CABLE ENTRY
PCD 73
Ø24
4-Ø5.5 HOLES
Ø90
4-Ø6 HOLES
45.5 66
Ø11 CABLE ENTRY
PCD 73
Ø24
Ø90
51.567
4-Ø5.5 HOLES
Ø18 CABLE ENTRY
PCD 71~73
Ø24

ISO International Organization for
Standardization
IECEx
International Explosion
Qlight qualityassurance systemshavebeen
KS Q ISO 9001:2009 regulation.
RoHS2 Restriction of Hazardous
SubstancesDirective
Qlight c omplieswiththe RestrictionofHazardous
Substances Directive by limiting itsuse of hazardous
materials.
KR Korean Register of Shipping
Qlight’s design and qualityassurance system has
CCS
Qlight’s design and qualityassurance system has
ATEX The EuropeanRegulatory
Framework or Manufacture,
Installation andUse of Equip-
ment in ExplosiveAtmospheres
Qlight’sexplosion proof products comply with ATEX
Directives 94/9/EC.
manufactured and manage according to
international standards.
NEPSI National Supervision and Inspection
Center for Explosion Protection
and Safety of Instrumentation
Qlight’s design and manufacturing system
meetsthe People’s RepublicofChina National
explosion proof Standard.
(Chinese Standard-GB3836/GB12476)
KCs Explosion Proof Device
Safety Certification System
The safety performanceofmachines and
Technical capability and production system have
standards.
TIIS Japan Explosion-proof
TIIS is a Japanes explosion proof test and certification
system accordance with the Ministry of Health, Labour
and Welfare Notice and the explosion proof guidelines for
factory electrical equipment. Qlight's explosion proof
products hasve been tested and certified by TIIS.
UL Underwriters Laboratories
Qlight’s design and quality assurance system has
been certified from UL to ensure the stability
of consumption goods and to protect consumers.
CCC
CCCF
Security & Protection
Qlight’s has obtained CCC which guarantees safety,
protection against fraud, environment, etc.
Qlight has passed therigorousexaminationprocess
of "Passing Fire Protection Products Centering" In order
to sell fire-fighting products such as fire alarm equipment
to Chinese market.
CE EuropeanCommission
KC
Commission.
LR Lloyd’s Register
RMRS Russian Maritime
Registerof Shipping
Qlight’sdesign and quality assurancesystemhas
Qlight’s products are certified by KC for preventing
accident caused by fire.
Qlight’s design and quality assurance systemhas
Shipping.
ICAO International Civil Aviation
Organization
Qlight guarantees ourproducts satisfy the criteria
regulated by the International Civil Aviation
Organization(ICAO, FAA).
E-mark Commission Directive
Regarding Vehicle Industry
KCC
Conformity Assessment of Broad-
casting Communication Equipment
Qlight hasobtained EU mark forapprovedvehiclesand
vehicle components sold into theEU(EEA :European
Economic Area)
environment that causes unwanted electromagnetic
waves from thedevice, communication failure due to
other devices or external radiowaves, and malfunction
of the device.
Qlight has been certified to protect the electromagnetic
Technical Certication
• Qlight products are designed to meet strict quality and technical standards. Thus, the Qlight brand is widely recognized for its high quality
and technical innovations from leading institutions around the world.

MEMO

MEMO

Qlight Co., Ltd. www.qlight.com | [email protected]
Head O󰀩ce | Suite #1510, STX-V Tower, 128 Gasan digital 1-ro, Geumcheon-gu, Seoul, Korea
Tel. [phone](Toll free. [phone]) Fax. [phone]
Factory | 185-25, Mukbang-ro, Sangdong-myeon, Gimhae-si, Gyeongsangnamdo, Korea Tel. [phone](Toll free. [phone])
Qlight OverSEAs Sales Dept | 704 Nakdong-daero, Sasang-gu, Busan, Korea(Eomgung-Dong) Tel : [phone]
Qlight Public Relations & Marketing Team O󰀩ce | 704 Nakdong-daero, Sasang-gu, Busan, Korea(Eomgung-Dong) Tel. [phone]
Qlight USA, Inc. www.qlight.com www.qlightusa.com | [email protected]
3003 North First Street, Suite #341, San Jose, CA 95134 USA Tel. +1 - 408 - 519 - 5740 Fax. +1 - 408 - 519 - 5739
SHANGHAI Qlight Electronic Co., Ltd. www.qlight.com www.qlightcn.com | [email protected]
China Factory/ Shanghai Sales O󰀩ce | #19, Nanda Road, Baoshan Area, Shanghai, China Tel. +86 - 21 - 6651 - 7100 Fax. +86 - 21 - 6315 - 3929
China Factory Site 2 (Qidong) | #33, Haiyan Road, Qidong High-tech Industrial Development Zone, Qidong, Jiangsu Province, China
Tel +86 - 513 - 8384 - 9999 Fax +86 - 513 - 8384 - 9910
Product Operation Inquiry / Customer Support [phone]
You can expect prompt service if you have exact information such as model name, symptom, telephone number and address.
※ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Head office : Suite #1510, STX-V Tower, 128 Gasan digital 1-ro, Geumcheon-gu, Seoul, Korea (Postal Code : 08507)
Factory : 185-25, Mukbang-Ro, Sangdong-Myeon, Gimhae-Si, Gyeongsangnam-Do, Korea (Postal Code : 50805)
For your safety
Specication and dimensions listed in this catalogue subject to change without notice for product quality improvement.
The newest product information is available on our website.(www.qlight.com)
Please read the instruction manual attached to the product carefully before installation and use.
www.qlight.com
EN - ST45ML-USB - 2106A