QSC Q-SYS PAge Station User manual

1
Page Station Quick Start Guide
Mounting the Hand-held Microphone Models
NOTE: The product shall be installed in accordance with the applicable local
code requirements.
Q‑Sys Page Stations are designed to be mounted on a wall or podium with an appropriate cutout and
cavity to allow all cables and power sources to connect to the Page Station rear panel with adequate
stress relief. The included Mounting Bracket is designed to mate with a standard triple‑gang U.S.
electrical box, but can be mounted directly to the wall.
1. Remove the Mounting Bracket from the Page Station. It is secured by one screw on the front edge of
the Page Station. Refer to Figure 3-1. Set the screw aside for later use.
Refer to Figure 1.
2. Place the Microphone Strain‑relief Clamp (1) over the Microphone cable (2).
3. Plug the RJ‑45 plug (3) into the receptacle (4) on the Page Station.
4. Install screw (5) through the clamp and into the Page Station to secure the Mic cable.
5. Route all Page Station wiring and connectors through the center of the Mounting Bracket.
6. Use four tripple‑gang screws (included) (Figure 2-1) to align and mount the Mounting Bracket to the
triple‑gang electrical box if you are using one.
7. Use six screws (not included) (Figure 2-2) to secure the Mounting Bracket to the wall. The six screws
shall be appropriate for the surface to which the Page Station is mounted.
IMPORTANT: The six screws, securing the Mounting Bracket to the wall, are required
even when using the triple‑gang electrical box.
8. Connect all Page Station wiring to the proper connectors on the Page Station. Refer to "Page Station
Configuration and Setup" on page 2.
Refer to Figure 3.
9. Tilt the top of the Page Station back and install the Page Station onto the
Mounting Plate by aligning the two tabs on the Page Station with the two slots
on the Mounting Plate.
10. With the Page Station still tilted, carefully bundle the wiring back into the wall
(or triple‑gang electrical box).
11. Push the bottom of the Page Station to the wall.
12. Install and tighten the screw (1) (removed in step 1) through the Mounting
Bracket up into the Page Station.
NOTE: Use these installation instructions to mount the
Hand‑held Page Station models to other surfaces as well.
™
— Figure 1 —
1
1
2
3
4
5
— Figure 2 —
1
2
— Figure 3 —
1
Mounting tabs
on back of
Page Station
TD-000359-00-A
*TD-000359-00*

2
Mounting the Gooseneck Microphone Models
There are two methods of mounting the Gooseneck Microphone Page Stations. You can mount the
Page Station onto the mounting surface using the Angle‑Mount Bracket giving the Page Station a 30°
angle to the mounting surface. The second method uses the optional Podium‑Mount Bracket which
allows for mounting into a podium or other surface so that the Page Station surface is flush with the
mounting surface. The first method is discussed in this document, while the flush, or Podium‑Mount
(PS‑ACC) is an optional accessory with separate instructions.
1. Select the mounting surface for the Page Station. The surface should have enough access‑room
below it to allow for installing the attaching hardware and the Page Station cables.
2. Place the Angle‑Mount Bracket on the surface oriented as you wish.
Refer to (Figure 4)
3. Mark four screw holes (one in each corner) along both bottom sides of the Angle Mount bracket.
4. Optionally, you can make an opening in the mounting surface for the cables under the bracket, or feed
the cables through the slot at the bottom‑back side of the bracket.
5. Use a 1/4” drill bit to drill the six holes.
Refer to (Figure 5)
6. Use a Phillips screwdriver to remove and discard the top two screws on the back of the Page Station.
7. Align the Angle‑Mount Bracket (2) with the holes drilled in step 5and insert six bolts (not supplied)
through the Angle‑Mount bracket and mounting surface, then secure with the appropriate hardware.
8. Connect all Page Station wiring to the proper connectors on the Page Station. Refer to "Page Station
Configuration and Setup" on page 2.
9. Hold the Page Station (1) horizontally above the Angle‑Mount Bracket (Figure 6) and lower
the Page Station down onto the bracket so that the two tabs (3) on the Page Station slide into
the two slots (4) on the bracket.
10. Lower the front of the Page Station down onto the bracket. Make sure the two tabs on the Page
Station remain engaged with the two slots in the bracket.
CAUTION!: Make sure that the wiring is secured for stress relief.
Refer to Figure 7.
11. Insert the socket‑head cap screw (1) through the bracket and into the Page Station. Tighten
with a 9/16" hex wrench.
Page Station Configuration and Setup
Q‑Sys Designer is the software application required to configure your paging system. Refer to the
Q‑Sys Designer online help for details.
Optional Connections
The following are optional, and should be connected prior to powering up the Page Station.
• MIC/LINE (3‑Pin Euro)
• LINE OUT (3‑Pin Euro)
• GPIO (6‑Pin Euro)
• AUX POWER (If you plan to use PoE, do not turn the auxiliary power supply on until you have
made the network connection with PoE turned on.
• LAN‑B — Connect in the same way as LAN‑A described below.
• Page Station Expander Adapter, for use with the Q‑Sys Page Station Expander.
— Figure 4 —
1
— Figure 5 —
— Figure 6 —
1
2
3
4
— Figure 7 —
1

3
Required Connections
• LAN‑A — Connect one end of a Cat 5e cable with an RJ45 connector to the LAN‑A connector on the Page Station. Connect the other end of the
cable to the Q‑LAN network.
When power is supplied to the Page Station it may take several minutes to boot fully. The message "Q‑Sys not configured" displays. This message
remains until the network details are configured for the Page Station and it is included in a valid paging design.
About PoE and AUX POWER
There is no On/Off switch for the Page Station, making the order in which the power is connected important. The following information describes the
events when power is lost based on which power is supplied to the Page Station first.
• If AUX POWER is supplied first:
• The Page Station boots using AUX POWER.
• If PoE is then connected, it is not used.
• If AUX POWER fails, power to the Page Station is lost, the Page Station re‑boots using PoE.
• If PoE fails with AUX POWER still available, there is no effect ‑ PoE was not being used.
• If PoE is supplied first:
• The Page Station boots using PoE.
• If AUX POWER is then connected, it is not used.
• If PoE fails, the Page Station switches to AUX POWER. There is no re‑boot.
• If AUX POWER fails with PoE still available, there is no effect AUX POWER was not being used.
• If PoE returns, the Page Station remains on AUX POWER.
RoHS STATEMENT
The Q‑Sys Page Stations products are in compliance with European Directive 2002/95/EC – Restriction of Hazardous Substances (RoHS).
The Q‑Sys Page Stations products are in compliance with “China RoHS” directives. The following chart is provided for product use in China and
its territories:
Q‑Sys Page Stations
部件名称
(Part Name)
有毒有害物质或元素
(Toxic or hazardous Substances and Elements)
铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
(Cr(vi))
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
电路板组件
(PCB Assemblies)
X O O O O O
机壳装配件
(Chassis Assemblies)
X O O O O O
O: 表明这些有毒或有害物质在部件使用的同类材料中的含量是在 SJ/T11363_2006 极限的要求之下。
(O: Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this part is below the limit requirement in SJ/T11363_2006.)
X: 表明这些有毒或有害物质在部件使用的同类材料中至少有一种含量是在 SJ/T11363_2006 极限的要求之上。
(X: Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used for this part is above the limit requirement in SJ/
T11363_2006.)

4
If you would like a full copy of the Page Station User manual, visit the QSC Audio Products website at www.qscaudio.com, or
contact Customer Service [phone] or toll free (USA only) [phone] to receive a copy by mail.
Si desea obtener una copia completa del manual del usuario de la Page Station, visite el sitio web de QSC Audio Products en
www.qscaudio.com, o póngase en contacto con el Servicio al Cliente al [phone] o sin costo (sólo en EE.UU.) al (800)
772-2834 para recibir una copia por correo.
Pour obtenir un exemplaire complet du manuel d’utilisation de la Page Station, allez sur le site Web QSC Audio Products à www.Page Station, allez sur le site Web QSC Audio Products à www., allez sur le site Web QSC Audio Products à www.
qscaudio.com ou contactez le service clientèle au [phone] ou au [phone] (numéro vert - USA seulement) pour
recevoir un exemplaire par courrier.
Ein vollständiges Exemplar des Benutzerhandbuchs für die Page Station finden Sie auf der QSC Audio Products-Website unterPage Station finden Sie auf der QSC Audio Products-Website unterfinden Sie auf der QSC Audio Products-Website unter
www.qscaudio.com. Sie können sich unter [phone] oder unter der (nur in den USA) gebührenfreien Nummer +1 (800)
772-2834 auch an den Kundendienst wenden, um sich ein Exemplar zuschicken zu lassen.
如果您需要 Page Station 产品用户手册的完整副本，请访问 QSC 音频产品网站 www.qscaudio.com，或致电客户服务部门 +1 714
957-7150，或拨打免费电话（仅限美国）[phone] 通过邮件获取副本。
Contact
Mailing Address
QSC Audio Products, LLC
1675 MacArthur Boulevard
Costa Mesa, CA 92626‑1468 U.S.
Main Number
(714) 754‑6175
World Wide Web
www.qscaudio.com
Sales & Marketing
Voice
(714) 957‑7100 International
Toll free (U.S. only) (800) 854‑4079
FAX
(714) 754‑6174
E-mail
[email protected]
Support
24/7 Support
QSC offers 24/7 support on Q‑Sys™
Networked Audio Systems only.
Full Support
Business Hours: 6 AM to 5 PM Pacific Time (Mon‑Fri)
Tel. 800‑772‑2834 (U.S. only)
Tel. [phone]‑7150
Fax. [phone]‑6173
Q-Sys Emergency-only After-Hours and Weekend Support*
Tel: +1‑888‑252‑4836 (U.S./Canada)
Tel: +1‑949‑791‑7722 (non‑U.S.)
* After hours calls are guaranteed a 30 minute response time from a
Q‑Sys Support Team member for Q‑Sys ONLY!
E-mail
[email protected]
(immediate e‑mail response not guaranteed. For URGENT issues use
the phone numbers above.)
Q-Sys™ Customer Support
© 2011 - 2012, QSC Audio Products, LLC. QSC Audio Products, LLC. All rights reserved. QSC and the QSC logo are registered trademarks of QSC Audio Products, LLC in the U.S.
Patent and Trademark office and other countries. Q-Sys, Q-LAN, Q-Sys Core Processor, Q-Sys Core 1000, Q-Sys Core 3000, Q-Sys Core 4000, Q-Sys I/O Frame, and Q-Sys
Designer are trademarks of QSC Audio Products, LLC. Patents may apply or be pending.